Liberty 636 Bedienungsanleitung

Liberty 636

Liberty 36v Folding Bike

Thank you for your decision to buy this product.

Please use this product according to the instructions.

Please keep the instructions in a handy place.

Liberty 636 Folding Electric Bike

36 Volt/10 ah Li-ion

User Manual

Introduction

Dear Customer,

Wow! You are excited! You have just received your brand new ebike. We, too, are excited because as designers and developers of our

bikes, we love to make you happy, and we believe your new ebike will give you lots of fun. I know you want to get this bike on the

road immediately, but please STOP!

Why? Well, first of all, you need to charge your batteries fully before using them. So, while your ebike is charging, take the time to

read this manual. We have worked hard to make it as readable as possible. This manual will help prevent injury and teach you how to

care for your new ebike.

It is the owner’s responsibility to carefully read all of the contents of this manual and to comply with all laws pertaining to the

operation of bicycles and/or electric bicycles in your local jurisdiction. If you have any questions, please consult with the laws web

page on www.iloveEbikes.com or consult your local department of motor vehicles for clarification.

These electric bikes are not classified as motor vehicles, however, to drive them on the roads various states have differing laws.

We have worked hard to provide you a quality, well-designed product without defects. That is our responsibility. You, too, have a

part to play. With proper care, maintenance and attention to bicycle safety rules, your ebike will give you years of enjoyment.

Please read the instructions carefully before using your ebike. Do not ride this bicycle until you have read and thoroughly

understand the owner’s manual. It contains information critical to your safety. If you have questions about the operation of this electric

bicycle, consult your authorized dealer. It is extremely important that you follow the safety guidelines contained in this manual in

order to ensure your maximum safety. If you loan your bike to anyone, make sure they also know how to operate it safely.

When using, the load should not be greater than the maximum capacity, and please pay attention to increase the braking distance

during rainy or snowy days.

This ebike can operate in the rain and snow, but it CANNOT be submerged in water. When the motor is submerged in water, it

may short circuit and fail, which is NOT covered by the warranty.

Please don't dismantle and repair the spare parts by yourself, but go to the local dealer.

Please take time to record the following information:

Recording Your Ebike Info

Serial

Number: _______________________________________________________

Model: ___________________636________________________________

Color: _______________________________________________________

Date of

Purchase: _______________________________________________________

Dealer’s Name: _______________________________________________________

Dealer’s Ph. #: _______________________________________________________

Dealer’s Email: _______________________________________________________

The serial number is stamped on the

motor.

Important Instructions

Safeguard your battery to insure continued high performance. It should be recharged after each use. The normal full-cycle battery

life, if it is continuously discharged and recharged, is between 300–1000 cycles (depending on which battery came with your bike)

after which the storage capacity of the battery will gradually decline.

CAUTION! Fully charge the batteries before the first use!

Failure to do this can result in decreased battery performance for the life of the bike. Fully charge the battery each time you use the

bike.

Battery performance is affected by the temperature and is generally better in warm temperatures. When the temperature is below

32º F (0º C), the battery current may decrease by a third. Consequently, the travel range on a full charge in cold environments is much

less, but will return to normal when the temperature is back to room temperature.

Frequent stopping and starting, riding uphill, traveling against a strong wind, starting from a standstill, riding on rough or muddy

roads, and carrying more than one person or heavy loads will consume extra battery power and shorten the range. A few tips to

prolong the battery life during these conditions is as follows:

Frequent braking – try to look ahead and coast rather than frequently stopping and starting.

Riding uphill or against a stiff wind – pedal to supplement the battery power.

When starting from a standstill, use the pedals to help bring you up to speed.

When the battery meter indicates the voltage is low, switch to manual power and avoid using the battery, so you don’t

shorten the battery life.

To prevent premature failure of your battery and for your warranty to remain in effect on your battery, YOU MUST CHARGE

AND DISCHARGE THE BATTERY AT LEAST ONCE PER MONTH.

Always turn off the motor and remove the key from the ignition before and during charging to

prevent serious damage to the controller and to the batteries!

This electric bicycle can be used in the rain, however, the motor and other electrical parts must not be submerged in water.

The controller, motor and other electrical devices may be short circuited causing damage, which is NOT covered by warranty, and

creating possible dangerous situations.

DO NOT use chargers or other components other than that which has been approved

and tested by this company. This company is not responsible for damages caused by the use of other

products not specifically designed and tested for use with this electric bike.

Battery chargers contain sensitive electronics. Improper use, dropping, or sudden jolts can damage the charger and its internal

electronics which is NOT covered by warranty. Do not leave the charger on for more than 10 hours!

Check all nuts, bolts, screws, and spokes to make sure they are tight before riding. If any screws, nuts, or bolts are loose, put some

thread lock on the threads and then tighten.

When riding down hill, you MUST have the key on even if you are NOT using the

throttle and even if the battery is not in the bike. The motor will generate enough

electricity to RUIN your controller which is NOT covered by warranty.

Table of Contents

...............................................................................................................Introduction 2

...............................................................................................Important Instructions 3

......................................................................................................Table of Contents 4

..................................................................................................................Assembly 5

.....................................................................................................Safety Precautions 7

.................................................................................General Operating Instructions 8

................................................................Battery Charging and Battery Precautions 9

................................................................................Specific Operating Instructions 10

.............................................................................................................Maintenance 11

........................................................................................................Troubleshooting 12

...................................................................................................................Warranty 13

.......................................................................................Federal Electric Bike Law 14

ASSEMBLY

Only minimal assembly is required for your new ebike. You will be required

to do the following:

Unfolding the Frame

The frame of your bike folds in the middle. The quick-release latch is

released and lifted up to allow the locking pin to release and unfold the bike.

Insert Upper Handlebar Stem

Your bike upper handlebar stem is inserted into the lower stem and is

tightened with the quick-release handle as in picture. You can snug up the

quick release with the hand nut opposite the handle to get the proper

tightness.

Unfold the Handlebars

Unfold the handlebars and lock into place.

The hinge has a quick-release that is released

and slid off the base and then needs to be slid

to one side to unlock the hinge.

Adjusting the Seat

The seat is adjusted with the quick-release.

The tightness of the quick-release clamp can

be adjusted with the hand nut on the opposite

side of the handle.

Fastening Headlight

To fasten the headlight follow the steps

below:

1. Loosen the bolt that holds the front fender.

2. Slide front headlight bracket onto the bolt

that you removed. For best performance, turn

the nut so the hex head fits into the slot on

the headlight bracket.

3. We recommend you use threadlock on all

bolts and nuts to insure that they do not

vibrate loose during use.

4. Tighten hex head with a 10mm wrench to

make sure headlight is at the correct angle

for shining on the path ahead.

Unfolding Frame

Tighten Handlebar

Handle

Folding

Tighten Headlight Bracket

Seat Release

Loosen bolt

Installing the Pedals

•Note the left and right of the pedal.

•[ L ] left [ R ] right are stamped on the

threaded end of the pedal.

•Attach the L pedal to the L crank, then R

pedal to R crank.

•Screw the pedals in and tighten them fully.

The L pedal has left-hand threads, and the R pedal has right-hand threads.

Misapplication is not covered under warranty.

Brake Adjustment

Your bike’s front and rear brakes have a pad that ride on the rim of the wheel for braking. These are adjusted by

tightening the cable and by adjusting the stem of the pad. The front brake should be adjusted so that it slows the

tire but cannot make it skid. The rear brake should be adjusted so that if necessary it can skid the tire. Adjust the

pads on both sides of the bike. Cables also have adjustment at the brake levers on the handlebars.

Take note that the rear brake is on the left side of the handlebar, and the front

brake is on the right side of the handlebar.

Cable adjustment

Pad adjustment

Safety Precautions

• Before operating your bicycle, inspect it carefully to avoid accidents or damage.

• Do not drive close to other vehicles.

• ALWAYS keep the power switched OFF until you are seated on the bike and ready to ride.

Turning the power on and then accidentally twisting the throttle can result in the bike

lurching forward and may cause an accident, damage, or injury.

• NEVER attempt to disassemble the motor, battery, controller or throttle. This can result in

injury, fire, or damage to the bike.

• ONLY use the charger supplied with your bike to charge the battery. Using the improper

charger can result in fire or explosion.

• KEEP the batteries out of the reach of children.

• Obey all traffic laws relevant to the operation of bicycles and electric bicycles.

• Use the turn signals (if equipped) or hand signals at all times when making turns.

• KEEP both hands on the handlebars at all times.

• DO NOT hang objects on or under the handlebars.

• DO NOT brake suddenly in the rain or on slippery, wet surfaces.

• USE extreme caution when riding near other vehicles. Assume they do not see you, and be

careful at intersections and when starting from a stopped position.

• When cleaning your electric bike, do not use a steady direct stream of water from a hose. Use

a cloth to avoid short-circuiting any electrical components. Your electric bike has a durable

finish and does not need to be waxed. Clean with a mild detergent and buff to restore its

original shine.

• Please wear a safety helmet and glasses for your own protection whenever riding.

• Wear bright clothing to help make you visible to other motor vehicles.

•Do not wear loose clothing that can become caught on the bicycle.

•Do not leave the charger connected to the battery for more than 10 hours.

General Operating Instructions

BEFORE YOU RIDE

1. Charge your battery until the green indicator light on the charger comes on, but do not allow it to charge more

than 10 hours.

2. Check the air pressure of the tires. Make sure they are at the recommended psi embossed on the sidewall of

the tire.

3. Check the front and back brakes, and the condition of the front and back wheels, handlebar, and saddle. Make

sure they are tight and fastened. Make sure all quick releases are locked and secure and that all parts are in

good working order. Inspect your bike completely.

4. If it was removed, install the charged battery in the battery seat of bike and lock it.

5. Raise the kickstand.

6. Sit on the bike and turn the bike on. The power lights/meter should show your battery capacity.

7. Pedaling or using the throttle on the right hand will begin to accelerate the bike.

ATTENTION: After the power is on, if the rider twists the throttle the bike will lurch forward! Do not

turn the power on until you are ready to go.

The hand brake will automatically cut the power to the motor as also will releasing the throttle. While starting

or climbing a hill, pedal as much as possible, so that the electric power will not be drained too much. At the

same time, it can lengthen the life of the battery and motor.

ATTENTION: When riding down hills, do not turn off the power, otherwise the controller and motor will

be easily damaged which is NOT covered under warranty.

While running, if the battery power is getting low, the battery meter will lessen. At this time you should pedal

your ebike like a regular bike and charge the battery as soon as you get to an electrical outlet. Turn off the

power and remove the key while parking. If you decide to push your bike for any reason, make sure to turn the

power off, so you don’t accidentally turn the throttle making the electric bicycle start suddenly and cause an

accident. To help get the best distance out of your electric bike, refrain from a lot of braking and coast as much

as possible.

Battery Charging

It is important that you charge your batteries after every use. This

will extend the total life of your battery. Once the charger has

indicated that your battery is fully charged the green light will come

on, unplug the power source from the bicycle and the electrical outlet

and store in a cool, dry place. Do not leave the charger plugged into

the battery for long periods of time as this can damage the battery.

1. Turn the key to OFF and remove the key.

2. Insert plug of the charger into charging port of the battery box.

You can charge your battery while still in the bike or your can

take it out of the bike and charge where it is most convenient.

3. Insert the charger into the wall outlet. Do not plug charger into outlet until you first plug the charger

into the battery charging port. A red light will come on. It can take up to 8 hours to recharge the battery

completely. On most chargers, a green light will appear when it is fully charged.

4. When the light turns from red to green, it indicates that the battery is full. If possible, charge for an

additional 2-3 more hours to fully balance the battery.

After the green light comes on, the charger is in trickle charge mode. If you will be gone for many hours,

you should unplug the charger. This is especially true in hot weather. Avoid overcharging and damaging the

battery. The charger will become warm during charging, so keep charger away from any flammable materials.

You can also charge the battery when it is removed from the bicycle. This is especially convenient during cold

nights or when your bike is not parked near an electrical outlet. Because specifications of the charger may

change in the process of production, please read the information on the charger itself or the charger manual (if

included) in detail before using. Always charge the bike in a dry and clean place. Keep the charger dry and

clean.

Battery Precautions

•Do not touch the two poles of the battery with your hands when the battery is removed for charging. Also, the two battery poles

should not be touched with any metal or other material that conducts electricity.

•While charging, put the battery in a secure place where children can't reach.

•Do not use any charger other than the one that came with your Liberty Electric Bike. If you need another charger, contact your

local dealer.

•Do not attempt to open or repair your charger. The electronics contain high-pressure circuits, so don’t dismantle by yourself.

•Prevent liquids, metal and metal filings from permeating the charger, and be careful to not drop or hit the charger which could

cause damage.

•Do not put anything on top of the charger while charging. It must be well-ventilated to allow all the heat generated to dissipate.

•When charging, if there is a peculiar smell or the temperature is too high, please stop charging immediately.

•To prevent premature failure of your battery and for your warranty to remain in effect on your battery, YOU MUST CHARGE

AND DISCHARGE THE BATTERY AT LEAST ONCE PER MONTH. Do NOT use in the battery in a very low state.

•The charger will produce heat up to 185°F (85°C) in the course of using, so keep it away from flammable articles while using.

•It is normal that the mileage capacity will reduce as a result of low temperatures.

•While carrying the charger, DO NOT bump, drop, or damage, otherwise it may result in failure.

•Avoid any contact with water when charging your battery. If a plug or socket gets wet, dry it completely before using.

•Do not leave the charger connected to the battery and the outlet for more than 10 hours.

•Always use the charger according to the instructions.

Removing the Battery from the Bike

•Loosen the quick-release from the seat

and lift seat from the seat post.

•Turn key to release the locking pin.

•Lift handle on top of the battery and

slide out battery from its position in

the bike.

Specific Operating

Instructions

Your bike has a KEY switch on the battery with an ON/OFF

position. A battery meter is located on the top of the battery

which shows the charge if you press the button next to the

battery meter.

To ride your bike your key switch needs to be ON. Once it is

on, your handlebar battery meter will light up so you can see

how much charge is in your battery. Always make sure it is at

full charge when you begin to ride your bike.

The light switch is located on the left handlebar. Press the red

button to turn the headlight ON or OFF.

Your bike is equipped with 6 speed shimano gears. You can

go through the gears by turning the left handlebar.

On the right handlebar is the throttle. You can start your bike

by pedaling or by twisting the throttle. As you pedal, the

motor will automatically help you if the key switch is in the

ON position on the battery.

Throttle

Battery Meter

Front Brake Handle

Bell

Light Switch

Gear Switching

Rear Brake Handle

Battery Meter

Inhaltsverzeichnis

Andere Liberty Fahrrad Handbücher

Liberty

Liberty 36v Bedienungsanleitung

Beliebte Fahrrad Handbücher anderer Marken

RAMBO

RAMBO R1000X2M-FF-BFD Bedienungsanleitung

Vermeiren

Vermeiren SAFARI Bedienungsanleitung

Velec

Velec A2/36V Bedienungsanleitung

Coswheel

Coswheel A-ONE Bedienungsanleitung

Betzold

Betzold 97869 Bedienungsanleitung

Cervélo

Cervélo S3 2019 Bedienungsanleitung

Tenways

Tenways AGO X Bedienungsanleitung

Festo

Festo EGSC-BS-KF Stücklistenhandbuch

Gio Electric

Gio Electric H1 Volt Bedienungsanleitung

GOGOBEST

GOGOBEST GM30 Bedienungsanleitung

DAHON

DAHON CIAO - 2009 Bedienungsanleitung

Aprimatic

Aprimatic ONDA 500 Kurzanleitung

MV Agusta

MV Agusta Lucky Explorer GRAVEL Gebrauchsanweisung

Greyp

Greyp G6 Series Bedienungsanleitung

Babboe

Babboe Carve-E Bedienungsanleitung

Huka

Huka orthros Bedienungsanleitung

Xtracycle

Xtracycle Stoker 2021 Bedienungsanleitung

APRILIA

APRILIA DORSODURO 750 ABS 2015 Bedienungsanleitung