Lightronics Show-Pro SM - 280 Bedienungsanleitung

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

SM - 280

DMX LIGHTING CONTROLLER

OWNERS MANUAL

March 24, 2008

OWNERS MANUAL Page 2 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

CONTROLLER FEATURES

280 DMX Channels - 14 units of 20 channel fixtures

14 Chases with up to 255 steps each

14 Scene banks with 22 scenes in each bank

Chases can be run with sound activation

Chases can be run at a preset speed and fade

2 Row X 16 Character LCD Display

DMX Polarity output switch.

Removable 4 MB Memory Card

Power Input: 13 - 15 VDC, 500 mA minimum

Power Connector: 2.1 mm, Center Pin +

Dimensions: 19"W X 9"H X 3.25"H

Weight: 6.7 Pounds

GENERAL DESCRIPTION

The SM-280 is a fixture (or scanner) oriented DMX

controller. It can control up to 14 fixtures of 20 DMX

channels each. The unit can also be used to control

conventional dimmer packs. The SM-280 includes 14

scene banks. Each bank can contain up to 22 scenes.

There are also 14 programmable chases. Each chase

may contain up to 255 steps. Scene banks can be

automatically run like chases.

Each fixture is permanently assigned a block of DMX

addresses. The table below shows the assignments.

The fixtures must be set to accommodate these DMX

assignments. This is usually done using DIP switches

on the fixture to set its starting address. Refer to the

fixture manual for exact instructions. The information

is sometimes shown on a tag or chart on the fixture. If

you set multiple fixtures to the same addresses then

they will controlled together.

FIXTURE FUNCTIONS

You will need to know which channel within a fixture

is assigned to each fixture function (Pan, Tilt, Color,

Dimming, etc.). This information is contained in the

fixture manual.

DMX CONNECTIONS

Any system using DMX control should be connected

together as a chain of devices. The control cable

should proceed from the controller to the first fixture

and then on to other fixtures in a continuous "daisy

chain" fashion. Most fixtures have a DMX IN and a

DMX OUT connector to be used to connect the chain.

The control cable should NOT be split into a multiple

run star arrangement with a cable running from the

controller directly to each fixture.

DMX CONNECTOR PIN ASSIGNMENTS

There are two different connectors which can be used

for DMX control. They are both XLR connectors.

Some units use 3 pin connectors. Others use 5 pin

connectors. The SM-280 transmits DMX from a 3 pin

female connector on the back edge of the unit. If your

fixtures use 5 pin connectors then you can make up an

adapter cable to accommodate this. The table below

shows the pin assignments.

Some fixtures use a reversed signal assignment. In

this case the DATA - and DATA + pins are reversed.

The SM-280 has a reversing switch on the back edge

to accommodate this situation.

DMX TERMINATION

A DMX chain should be terminated at the last fixture

(and ONLY the last fixture) on the chain. This is

done by installing a commonly available 1/4 Watt,

120 Ohm resistor across the DATA - and DATA +

wires at the last fixture. If you have only a few

fixtures close together and a very short run to the

controller then you may be able to operate without the

terminator.

Fixture # Channels

1 1-20

2 21-40

3 41-60

4 61-80

5 81-100

6 101-120

7 121-140

8 141-160

9 161-180

10 181-200

11 201-220

12 221-240

13 241-260

14 261-280

PIN # SIGNAL NAME

1 DMX COMMON

2 DMX DATA -

3 DMX DATA +

4 NOT USED

5 NOT USED

OWNERS MANUAL Page 3 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

CONTROLS AND INDICATORS

1 SCANNER / SCENES Buttons (22): Activates a

Fixture, Scene, Scene Bank, or Chase during

programming or operation.

2. Indicate which function the SCANNER / SCENES

buttons are enabled for.

3. Select which function the SCANNER / SCENES

buttons are enabled for.

4. Channel Faders (8): Sets DMX channel values.

Ch 1-8 can be adjusted when Page A is selected.

Channels 9 - 16 are adjusted using Page B.

5. Auto / Insert:

Auto: Activates Auto-Run for Scenes and chases.

Insert: Inserts a scenes and chase steps in

programming mode.

6. Delete/Music:

Delete: Deletes scenes, chase steps and chases in

program mode.

Music: Activates Music Auto-Run for scenes and

chases.

7. Copy: Copies fixture settings during setup. Copies

scenes and chase steps in program mode.

8. Setup/Group:

Setup: Activates setup operation which enables you

to control how the fixture will respond to

several controller functions.

Group: Causes up to 6 Banks of Auto-Run scenes

to run at the same time.

9. X Fine: Activates pan control for the Up/Down

buttons.

10.Y Fine: Activates tilt control for the Up/Down

buttons.

11. , 12. Up, Down: Changes channel DMX values

during manual fixture operation. Scrolls

through chase steps.

13.Fine: Switches the Pan/Tilt wheels and Up/Down

buttons between large and small DMX

increments. Enables setup of speed and

fade preset values for chase operation.

14.Memory Card: Reader/Writer for an external 4MB

memory card which can be used

to store scene and chase data.

15. LCD Display: Shows various controller status and

information depending on the

operation being performed.

Manual

Sel" Fi_sc_ba_ch

1 2 3

5 6 7 8

910 11 12 13

14 15 16 17 18

22 23 24 25 26 27 2821

OWNERS MANUAL Page 4 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

16. Spl Scene: Accesses one of 14 additional

scenes which are independent of

scenes in normal banks.

17. Tap / Display:

Tap: Controls the speed of Auto-Run Scenes and

chases. Push TAP several times at the rate

you want the scenes or chases to run. This is

an alternative to using the SPEED fader.

Display: Used to alter the format of some display

information items.

18. Pause: Temporarily stops Auto-Run scenes and

chases. The DMX channel levels will

hold their current setting during pause.

Push briefly to turn Pause ON or OFF.

19. Memory Select: Switches SM-280 operation

between internal memory and

the external memory card.

20. Page A/B: Controls which DMX channels are

active for the channel faders. Channels

1 - 8 are Page A. Channels 11 - 18 are

page B. Both A and B can be active at

the same time.

21. Program / Record:

Program: Switches the SM-280 into the program

mode. Hold it down for about 3 sec. to

toggle program mode ON or OFF. The

program mode indicator flashes when the

unit is in program mode.

Record: Used in program mode during recording of

scenes and chases. Also used in Setup to

record changes.

22. Speed Slider: Controls the speed of Auto-Run

scenes and chases. The range is

0.1 sec./step to 10 min./step. Also

used when assigning channel

functions in Setup mode.

23. Fade Slider: Controls the fade time of Auto-Run

scenes and chases. The range is 0

sec. to 30 sec.. Also used when

assigning channel functions in

Setup mode.

24. Power ON/OFF: Controls SM-280 main power.

25. Pan Wheel: Controls left/right operation of

fixtures when assigned.

26. Tilt Wheel: Controls up/down operation of fixtures

when assigned.

27. Fog Machine: Controls remote operation of

certain types of fog machines.

28. Black: (Blackout) Sets all DMX channels to zero

level output. A Setup procedure can be

used to prevent a fixture channel form

being affected by this function.

REAR PANEL CONNECTORS AND CONTROLS

All SM-280 external connections are made at the rear

panel. A rear panel diagram identifies the connectors.

See the sections DMX CONNECTIONS and DMX

CONNECTOR PIN ASSIGNMENTS for details about

the DMX signal connections.

DO NOT APPLY AC LINE POWER TO THE FOG

MACHINE CONNECTOR. It is only for remote

control of certain compatible fog generating machines.

CHARACTER SYMBOLS IN THE DISPLAY

The controller LCD display often will show the *

(asterisk) character for a value which has not yet been

set or selected. Unless a specific example is being

given the display diagrams in this manual will show

the * character as place holders instead of the actual

characters.

INITIAL CONTROLLER SETUP

Several SM-280 functions can be modified to change

the way that a fixture responds to the controller.

1. You can rearrange fixture channel assignments.

2. You can reverse the action of the faders.

3. You can select whether or not a fixture channel is

affected by the controller fade time.

4. You can change the effect of the blackout function

for fixture channels.

The Setup Mode is used to control these functions.

ENTER SETUP MODE

1. Push Setup. The display will appear as below.

2. Push Fixture and select a fixture by pushing its

Scanner / Scene Button (1 - 14). The display

below uses fixture 1 as an example.

Setup

Select: + / –

Sel" Fixture 01

Setup: Scanner

OWNERS MANUAL Page 5 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

From this point you use the Up and Down buttons to

scroll through the available setup options for a fixture.

You can exit Setup mode by pushing Setup again.

ASSIGN FIXTURE CHANNELS

The channel assignments within a fixture can be

assigned to other faders or the PAN or TILT wheels.

1. Enter Setup Mode and select a fixture.

2. Push Up. The display will show channel numbers

(Channel **) and corresponding controller fader

numbers (con *).

3. Use the Fade slider to scroll through the controller

fader numbers (con). The corresponding fixture

channel number will also be shown (channel). The

pan and tilt wheels are shown on the display as X

and Y respectively.

Use the Speed slider to change the fixture channel

number for the controller fader number displayed.

The example display below shows that the 3rd

channel in fixture 1 will respond to controller fader 2.

4. Push Program/Record to save the new channel

assignments. The controller indicators will flash

briefly.

REVERSE CHANNEL OPERATION

The action of the faders and PAN/TILT wheels can be

reversed. This normally used with PAN/TILT

controls but can be applied to other functions.

1. Enter Setup Mode and select a fixture.

2. Push Up or Down until the display shows as

below.

3. Use the Speed slider to scroll through the fixture

channels and use the fade slider to set the channel

to Y (yes) or N (no) reverse operation.

4. Push Program/Record to save the new setting.

The controller indicators will flash briefly.

SET CHANNEL FADE APPLICATION

You can control whether or not fade times will be

applied to a fixture channel. This is often used with

the pan and tilt channels.

1. Enter Setup Mode and select a fixture.

2. Push Up or Down until the display shows as

follows.

3. Use the Speed slider to scroll through the fixture

channels and use the Fade slider to set the channel

to Y (yes) or N (no) for fade application.

4. Push Program/Record to save the new

assignments. The controller indicators will flash

briefly.

SET CHANNEL BLACKOUT APPLICATION

Fixture channels can be set to respond to or ignore

blackout.

1. Enter Setup Mode and select a fixture.

2. Push Up or Down until the display shows as

follows.

3. Use the Speed slider to scroll through the fixture

channels and use the Fade slider to set the channel

to Y (yes) or N (no) for blackout application.

COPY FIXTURE SETTINGS

Once you have completed the setup for a fixture you

can copy those settings to another fixture. This is

useful when you have several of the same model

fixtures.

1. Enter Setup Mode and select a fixture which has

been already set up.

2. Push Copy. The display will be as shown as

follows.

Setup_Fixture **

Channel ** Con *

Setup_fixture 01

Channel 03 con 2

Setup_Fixture **

Channel ** Rev *

Setup_Fixture **

Channel ** fade*

Setup_Fixture **

Channel ** dark *

COP"Fixture **_A1

–> Fixture **_A1

OWNERS MANUAL Page 6 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

3. Select the fixture which will receive the settings by

pushing its SCANNER/SCENES button. The

display will show that fixture on the bottom row.

4. Push Program/Record to copy the assignments.

The controller indicators will flash briefly.

5. Push Copy again to exit from the copy menu.

MANUAL FIXTURE OPERATION

When the SM-280 is turned on it is in manual mode

with Blackout invoked. The display appears as

follows:

You can select a fixture (Fi), a scene (sc), a scene

bank (ba), or a chase (ch) by using its associated

button. Only manual fixture operation is covered in

this section since you have to be able to operate a

fixture to use it for programming scenes and chases.

1. Push Fixture. The display will show as follows:

2. Push a Scanner /Scenes button to select a specific

fixture. The display will show the fixture number.

You can select multiple fixtures to be controlled

together. Make sure Blackout is OFF.

3. Use the channel faders and/or pan/tilt wheels to

run the selected fixture. The display shows the

fixture number and the DMX value of the last

fader moved.

The Up and Down buttons can also used to adjust a

channel value. The X Fine and Y Fine Buttons can be

used to switch the Up/Down controls to the Pan and

Tilt channels.

If the fixture has more than 10 channels then you will

have to use Page A/B to switch to Page B to access

channels 11 - 20.

PAN AND TILT WHEELS

The Pan and tilt wheels default to channels 9 and 10

respectively and are shown in the display as X and Y.

They can be reassigned using the Setup mode.

COARSE/FINE CONTROL

The Fine button can be used with the Pan/Tilt wheels

and Up/Down buttons to adjust the applicable channel

in large or small increments. When the indicator on

the Fine button is ON - these controls will change the

channel DMX value in larger increments.

PROGRAMMING SCENES

A scene is a recorded snapshot of all the channel

settings of one or more fixtures. The SM-280 can

record 308 scenes. The scenes are arranged in 14

banks of 22 scenes each.

ALL SCENE ADD, COPY, INSERT, AND DELETE

FUNCTIONS ARE DONE IN THE PROGRAM MODE.

Press PROGRAM for about 3 second to activate the

program mode. The PROGRAM indicator flashes

continuously when program mode is active.

ADD A SCENE TO A BANK

1. Push Bank and select a bank to store the scene by

pushing a SCANNER/SCENES button (1-14).

2. Push Scene and select a scene to be stored by

pushing a SCANNER/SCENES button (1-22).

The display bottom row will show the bank number,

the number of scenes recorded in the bank, and the

scene you selected.

The display top row may show the last fader used and

its value.

3. Push Fixture and select a fixture by pushing a

SCANNER/SCENES button. You can select more

than one. The display will show the number of the

last fixture you select.

4. Adjust the fixture faders and/or Pan/Tilt wheels to

the desired settings as in manual fixture operation.

5. Deselect the fixture and select another one to

adjust. The first fixture will hold its settings.

6. Repeat steps 2 through 4 until all fixtures for the

scene are included.

7. Push Program/Record to store the complete scene.

The controller indicators will flash briefly.

Manual

Sel" Fi_sc_ba_ch

Sel" Fixture **

Manual

Hand_Fixture **

Slide * Data ***

E Slide * Da ***

Ban ** Sce ** / **

OWNERS MANUAL Page 7 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

You cannot store a scene beyond the next available

scene in a bank. For instance: If the bank has 4 scenes

in it and you try to program scene 7 then your scene

will be recorded but it will appear in scene 5.

EDIT A SCENE

You can edit the settings of one or more of the fixtures

in a scene without re-recording all the fixture settings.

This process does not apply to the last scene in the

bank. If you edit the last scene the results will be a

new scene.

The process is done in Program mode and is almost

the same as in described in ADD A SCENE TO A

BANK.When you select the scene it will activate the

fixtures in it. You can then alter the settings for a

fixture and record the scene with the changes.

INSERT A SCENE IN A BANK

This will insert a scene between two other existing

scenes in a bank.

1. Push Bank and select a bank to store the scene by

pushing a SCANNER/SCENES button (1-14).

2. Push Scene and select the scene which will become

the new scene by pushing a SCANNER/SCENES

button (1-22). For example: If you want to insert a

scene between scenes 2 and 3 you would select

scene 3. In other words the new scene will be

inserted before existing scene 3.

3. Push Auto/Insert.

4. At this point the process is the same as for

RECORD A SCENE. Select and set up the

fixtures as desired.

5. When all fixtures are set - Push Program/Record to

store the inserted scene. The controller indicators

will flash briefly.

DELETE A SCENE

1. Push Bank and select the bank containing the scene

by pushing a SCANNER/SCENES button (1-14).

2. Push Scene and select the scene to be deleted by

pushing a SCANNER/SCENES button (1-22).

The display will show the bank and scene number.

3. Push Delete/Music. The display will show as

follows

4. Push Program/Record to the complete the deletion.

The controller indicators will flash briefly.

COPY A SCENE

You can copy the contents of a scene to another scene

in the same or a different scene bank.

1. Push Bank and select a the bank containing the

scene to be copied using a SCANNER/SCENES

button (1-14).

2. Push Scene and select the scene to be copied to be

using a SCANNER/SCENES button (1-22).

3. Push Copy. The display will show the bank and

scene selected as follows.

4. Push Bank and select the Bank which will receive

the scene using a SCANNER/SCENES button (1-

14). The display will show as follows.

5. Push Scene and select the scene which will receive

the copy using a SCANNER/SCENES button (1-

22). The display top row will show the bank/scene

number to be copied. The bottom row will show

the bank and scene numbers where the scene will

be copied.

5. Push Program/Record. The copy will be made and

the controller indicators will flash briefly.

DELETE ALL SCENES IN A BANK

This will clear ALL the scenes in a bank.

1. Push Bank.

2. Hold down the SCANNER/SCENES button for the

bank you want to be cleared (1-14) and push

Delete/Music. The display will show the bank you

selected.

Bank_Del_Scen

Bank ** Sce **/ **

Ban ** Cop_sce

Select: Scen **

Bank_Delet

Delet –> bank **

Ban_sce_Copy

Select: Bank **

E" Ba 01 Sc **/ **

–> Ba 03 Sc **/ **

OWNERS MANUAL Page 8 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

3. Release both of the buttons and push the

SCANNER/SCENES for the bank again.

The display will show the bank number.

4. Push Program/Record to complete the deletion.

The controller indicators will flash briefly.

COPY A BANK OF SCENES

This will copy the programmed contents of a scene

bank to another bank. If the bank receiving the scenes

has more programmed scenes than the bank being

copied from then those scenes will be retained.

1. Push Bank.

2. Hold down the SCANNER/SCENES button (1 -

14) for the bank to be copied FROM and push

Copy. Then release both buttons.

3. Push the SCANNER/SCENES button for the bank

(1 - 14) which will be copied TO. The display will

show both the FROM and TO banks.

4. Push Program/Record to complete the copy. The

controller indicators will flash briefly.

PROGRAMMING CHASES

The SM-280 contains 14 user programmable chases.

Each chase may include up to 255 steps.

EACH CHASE STEP CONSISTS OF A SCENE

WHICH HAS ALREADY BEEN RECORDED.

A chase step can use any scene in any bank. Any

scene can be used in multiple chase steps and in

multiple chases.

ALL CHASE ADD, COPY, INSERT, AND DELETE

FUNCTIONS ARE DONE IN THE PROGRAM MODE.

Hold down Program/Record for about 3 seconds to

activate the program mode. The Program indicator

flashes continuously when program mode is active.

ADD A STEP TO A CHASE

This will add a scene at the end of a chase.

1. Push Chase.

2. Select a chase using a SCANNER/SCENES

button (1-14). The display top row will show the

chase number, the number of steps in the chase

and 000 for the current step.

3. Push Up. The display will show the bank number

(b), the scene number (s), the period or step time

(p), and the fade time (f) for the first step.

You can use Up/Down to scroll thru the existing steps.

4. Push Bank and select the bank number containing

the scene to be used for the new step by pushing a

SCANNER/SCENES button (1-14).

5. Push Scene and select the scene number to be used

for the new step by pushing a SCANNER/SCENES

button (1-22).

6. Push Program/Record. The scene will be added at

the end of the chase, The display will update and

the controller indicators will flash briefly.

7. Push Fine and use the Speed slider and/or Fade

slider to set the period and fade times.

8. Push Program/Record. The values will be recorded

and the controller indicators will flash briefly.

INSERT A STEP IN A CHASE

This is similar to adding a scene to a chase but the

scene will be inserted at a specific step and the

remaining steps will be pushed forward.

1. Push Chase.

2. Select a chase using a SCANNER/SCENES

button (1-14). The display top row will show the

chase number, number of steps in the chase, and

the current step.

3. Push Up and or Down to scroll to the step where

the scene will be inserted. The display will show

the bank number (b), the scene number (s), the

period or step time (p), and the fade time (f) of the

Bank_Copy

Ban ** –> Ban **

E"cha <**> ***/ ***

ViewStep? + ^ –

E"cha <**> ***/ ***

b ** s** p**** f ****

E"cha<**> ***/ ***

Viewstep? + ^ –

OWNERS MANUAL Page 9 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

chase steps. The scene will be inserted in front of

(before) the step you select.

4. Push Bank and select the bank containing the

scene to be used for the new step by pushing a

SCANNER/SCENES button (1-14).

5. Push Scene and select the scene for the new chase

step using a SCANNER/SCENES button (1-22).

6. Push Auto/Insert. The display bottom row will

show the bank and scene you have selected.

7. Push Program/Record. The scene will be inserted,

the display will update, and the controller

indicators will flash briefly.

DELETE A STEP IN A CHASE

This will remove a step from a chase. Steps following

the deleted step will close gap.

1. Push Chase.

2. Select a chase using a SCANNER/SCENES button

(1-14). The display top row will show the chase

number, the number of steps in the chase and 000

for the current step.

3. Push Up and or Down to scroll to the step which

will be deleted.

4. Push Delete/Music. The display bottom row will

show the step you have selected.

5. Push Program/Record. The step will be deleted,

The display will update, and the controller

indicators will flash briefly.

DELETE ALL STEPS IN A CHASE

This will clear the complete contents of a chase.

1. Push Chase.

2. Hold down the SCANNER/SCENES button for the

chase to be cleared (1-14) and push Delete/Music.

Release both buttons.

3. Push the SCANNER/SCENES button for the chase

again. The display will show the chase you

selected.

4. Push Program/Record. The chase will be cleared,

and the controller indicators will flash briefly.

COPY A SCENE BANK TO A CHASE

This will copy the contents of any scene bank into a

chase.

1. Push Chase and select a chase by pushing a

SCANNER/SCENES button (1-14).

2. Push Copy and select the bank to be copied by

pushing a SCANNER/SCENES button (1-14).

The display top row will show the selected chase, the

existing steps in the chase and the current step

number. The bottom row will show the scene bank

you selected. If the chase already contains steps then

the contents of the bank will be copied to the end of

the chase.

3. Push Program/Record. The bank will be copied

and the controller indicators will flash briefly.

COPY A CHASE

This will copy the contents of a chase to another one .

1. Push Chase.

2. Hold down the SCANNER/SCENES button for the

chase which will be copied (1-14) and push Copy.

3. Push the SCANNER/SCENES button (1-14) for

the chase which will receive the copy. The

display will show both chase numbers as follows.

4. Push Program/Record. The chase will be copied

and the controller indicators will flash briefly.

MANUAL SCENE OPERATION

You can manually activate a scene (1-22) in any bank

(1-14). Make sure that Blackout is OFF

1. Push Bank and select the bank containing the scene

you want to activate using a SCANNER/SCENES

button (1-14).

Chase_Delet

Delet _ Chase **

Chase_Copy

Cha ** –> Cha **

E" cha <**> ***/ ***

Copy _ Bank **

OWNERS MANUAL Page 10 of 12

SM - 280 DMX LIGHTING CONTROLLER Version 20080324

Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 757 486 3588

2. Push Scene. The SCANNER/SCENES button

indicators will show which scenes have been

programmed.

3. Push a SCANNER/SCENES button (1-22) to

activate a programmed scene. Its indicator will

flash continuously when the scene is active. The

display bottom row will show the selected bank,

the number of programmed scenes in the bank and

the currently active scene. The following example

display shows than bank 1 has 6 programmed

scenes and scene 2 is active.

MANUAL CHASE OPERATION

You can manually operate any chase (1-14) if it has

been programmed. This enables you to activate

(scroll through) the steps manually. Make sure that

Blackout is OFF.

1. Push Chase and select the desired chase using a

SCANNER/SCENES button (1-14).

The display top row will show the chase number, the

total number of steps in the chase, and the current

step number. The following example display shows

that chase 2 has been selected and it has 15 steps.

It also shows the current step number which is 000

since you have not yet activated a step.

2. Use Up and/or Down to activate the chase

steps.

The display bottom row will show details for the

current step. They include the bank number (b*), the

scene number (s**), and the preset speed (p****) and

fade time (f****).

AUTO RUN SCENE BANKS

The SM-280 can automatically cycle through the

contents of one or more scene banks at a user selected

speed and fade time. Multiple banks will run in the

order they are selected.

1. Push Auto/Insert.

2. Push Bank and select a bank (1-14) using a

SCANNER/SCENES button. You can select more

than one. The bank(s) will begin cycling. The

speed and fade time are dependent on the setting

of the Speed and Fade sliders.

The display will show detailed information for the

running banks and scenes.

You can combine the Auto-Run operation of up to 6

scene banks so that they will run at the same time by

pushing SETUP GROUP when multiple banks are

running. This is useful when one bank uses only some

of the fixtures and another bank uses different ones.

AUTO RUN CHASES

The SM-280 can automatically run one or more

chases at a user controlled speed and fade time.

Multiple chases will run in the order they are selected.

1. Push Auto/Insert.

2. Push Chase and select a chase to run by pushing a

SCANNER/SCENES button (1-14). The chase

will activate. The display will show the detailed

information for the chase including the total

number of steps in the chase, the current step

number, and the speed and fade time.

When the Speed and Fade sliders are positioned at the

bottom the chases will run at the preset speed and fade

time. You can adjust the speed and fade time using

these sliders. The speed range is from 0.1 sec./step to

10 min./step. The fade range is from 0 sec. to 30 sec..

You can also control the speed with the Tap/Display

while a chase is running. Push Tap/Display twice.

The interval between the taps will set the speed.

You can combine the Auto-Run operation of up to 6

chases so that they will run at the same time by

pushing SETUP GROUP when multiple chases are

running. This is useful when one bank uses only some

of the fixtures and another bank uses different ones.

M" Slide * da ***

Ban 01 Sce 06/02

M-Cha<02>015/000

b ** s ** p *** f ***

M-Cha<02>015/000

b ** s ** p *** f ***

f **** Sc < ** / **>

p **** Ar " Bank **

f **** St" ** / **

p **** Ar" Chas **

Inhaltsverzeichnis

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung