Lilin IPC0122WP3 Bedienungsanleitung

IPC0422E / IPC0422WE

1080P HD Covert Dome (WIFI) IP Camera

66-IPC0122CSM

Quick Installation Guide

IPC0122P3 / IPC0122WP3

1080P HD Covert (WIFI) IP Camera

CAUTION

Do not drop or strike this equipment

Do not install the equipment near any naked flames or heat

sources

Do not expose this unit to rain, moisture, smoke or dust

environment

Do not cover the opening of the cabinet with cloth and plastic

or to install this unit in poor ventilated places. Allow 10cm

between this unit and its surroundings

Do not continue to operate the unit under abnormal conditions

such as detection of smoke, strange smell or no display on

screen while power is turned on

Do not touch the power connection with wet hands

Do not damage the power cord or leave it under pressure

Do not operate this unit near magnet, speaker system, etc., to

avoid unnecessary magnetic interference

Connection cables should be grounded properly

The ITE is to be connected only to PoE networks without

routing to the outside plant.

L’ITE ne doit être connecté que sur un réseau PoE sans routage

vers l’alimentation extérieure.

-1-

English

Product Overview

①Indicator LEDs

Green: System status display.

Orange: SD status display.

Red: Alarm status display.

②RJ-12 Image Sensor Unit Input Connector

③Detection Sensor Input Connector (optional)

④Micro SD Card Slot

⑤Reset Key

Unit: mm

-2-

English

⑥Wi-Fi Antenna Plug (Wi-Fi Model Only)

⑦QR Scan Button (Wi-Fi Model Only)

1.Press and hold the button for 2–5 seconds to enter the QR

Scan Mode.

2.Press and hold the button for more than 6 seconds to enable

the AP mode.

⑧DC12V Power Input Jack (DC12V± 10%)

⑨Live Video Output RCA Jack

⑩Audio Input 3.5mm Phone Jack

⑪Audio Output 3.5mm Phone Jack

⑫Alarm In/Out and RS-485 Terminal

⑬RJ-45 Network Connector and Indicator LEDs

Green (LINK): Network connection. LED remains lit while

connection is in place.

Orange (ACT): Data communications. This LED should continue

to blink.

⑭Straight Mounting Bracket

○

15 Image Sensor Unit

○

16 RJ-12 Cable

○

17 Wi-Fi Antenna (2.4GHz) (Wi-Fi Model Only)

○

18 Image Sensor Unit (Dome Model Only)

Installation

Main Unit Installation

Please use a screwdriver to fixe the iron plates to the bottom base

-3-

English

(FIG.1), insert the provided screws (M4.0 x 25, wooden screw)

through the holes marked as "a," and secure the main unit to the

desired position (FIG.2).

Image Sensor Unit Installation

1. Drill a 5mm hole in the panel or on the wall (FIG.3).

2. Pull off the protector and attach the mounting bracket to the

panel (FIG.4).

3. Insert the sensor unit into the bracket (FIG.5), and secure the

unit with the screw. Ensure that the cone of the sensor unit is

flush with the panel (FIG.6).

-4-

English

Image Sensor Unit Installation (Dome Model)

1. To remove the bracket, loosen the screws on the left and right

sides of the sensor with a hex wrench (FIG.7), and remove the

three screw hole plugs off the bracket (FIG.8).

2. Follow the installation diagram and fit the screws to bracket

mounting holes marked as “a” (FIG.9) to secure the bracket to

any desired location. Then, attach the rubber plugs to their

original positions (FIG.10).

-5-

English

3. Connect the image sensor to the camera unit, and adjust the

angle of the lens (FIG.11).

4. To secure the upper housing and lens, tighten the screws on

the left and right sides of the lens with a hex wrench (FIG.12)

-6-

English

System Architectures

To connect the Covert IP Camera to the network, please deploy one

of the following system architectures:

(1). Use a DC12V power adapter and a network switch to connect to

the network.

(2). Use a PoE network switch to connect to the network.

(3). Use a PoE power injector and a network switch to connect to the

network.

(4). Use a DC12V power source to connect to the network through a

Wi-Fi router. (Wi-Fi model only)

-7-

English

Wi-Fi Setting Indicator (Wi-Fi Model)

QR SCAN MODE

STATUS, SD, and ALARM are

all lit

Enter the QR Scan Mode

STATUS and SD remains lit,

and ALARM is off

Scanning and recognizing the

QR code

STATUS remains lit, and SD

and and ALARM are off

Wi-Fi network connected

successful and AP router login

completed

AP MODE

STATUS is blinking

Activating AP mode

STATUS ALARM

-8-

English

How to Activate Connection in the AP Mode

1.Use a Wi-Fi enabled computer or smartphone to configure the Wi-

Fi IPCAM.

2.Search for a Wi-Fi IPCAM with an SSID of “IPCam-the last 6 digits

of MAC.” E.g., Wi-Fi MAC = 00-0F-FC-57-49-74, SSID = IPCam-

574974

3.A password is required to connect to the Wi-Fi IPCAM. The default

password is pass1234.

4.When connected, the default IP address of the AP mode is

192.168.15.1. You can use an Internet browser to change Wi-Fi

settings with this IP address.

Emergency Factory Default

To restore the hardware to factory default settings, please follow

these steps:

1.Press and hold “RESET Key” for 10 seconds and release.

2.Wait for about 40 seconds, and the network LED light should turn

off, and go back on again.

3.The camera is now restored to factory default settings, and will

reboot automatically.

4.Search for the IP device using the IPScan software.

5.Start the IP device via an Internet browser.

6.Enter the default username “admin” and password “pass” to

operate.

NOTE: For your convenience, the IP address will revert to the default

setting of 192.168.0.200.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lilin Sicherheitskamera Handbücher

Lilin

Lilin IPR722-IVS Bedienungsanleitung

Lilin

Lilin CMW158X2.2 Bedienungsanleitung

Lilin

Lilin IPD312S4 Bedienungsanleitung

Lilin

Lilin IPS6228E Bedienungsanleitung

Lilin

Lilin PIH-2522 Bedienungsanleitung

Lilin

Lilin CMR6082X Bedienungsanleitung

Lilin

Lilin ImegaPro IPS6224M Bedienungsanleitung

Lilin

Lilin PIH-2422 Bedienungsanleitung

Lilin

Lilin CMD2182 Bedienungsanleitung

Lilin

Lilin PIH-2622 Bedienungsanleitung

Lilin

Lilin PIH-7635DH Series Bedienungsanleitung

Lilin

Lilin Z2R8852AX Bedienungsanleitung

Lilin

Lilin PIH-2222 Bedienungsanleitung

Lilin

Lilin CMG176 Series Bedienungsanleitung

Lilin

Lilin IPD552EX4.2 N Bedienungsanleitung

Lilin

Lilin E1 Series Bedienungsanleitung

Lilin

Lilin ZMR7442X-P Bedienungsanleitung

Lilin

Lilin SP3034 series Bedienungsanleitung

Lilin

Lilin CMR7582N/P3.6 Bedienungsanleitung

Lilin

Lilin Z2R8122X-P Bedienungsanleitung

Lilin

Lilin CMG052X35 Bedienungsanleitung

Lilin

Lilin CMR6186X3.6 N/P Bedienungsanleitung

Lilin

Lilin iMEGAPRO LD2122E Bedienungsanleitung

Lilin

Lilin CMR70826 N/P Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung