Lilin ZR8022EX10 Bedienungsanleitung
ZR8022EX10/20
D/N 1080P HD Auto Focus IR IP Camera
66-ZR8022CSM
Quick Installation Guide
CAUTION
Do not drop or strike this equipment
Do not install the equipment near any naked flames or heat
sources
Do not expose this unit to rain, moisture, smoke or dust
environment
Do not cover the openin of the cabinet with cloth and plastic
or to install this unit in poor ventilated places. Allow 10cm
between this unit and its surroundin s
Do not continue to operate the unit under abnormal conditions
such as detection of smoke, stran e smell or no display on
screen while power is turned on
Do not touch the power connection with wet hands
Do not dama e the power cord or leave it under pressure
Do not operate this unit near ma net, speaker system, etc., to
avoid unnecessary ma netic interference
Connection cables should be rounded properly
The ITE is to be connected only to PoE networks without
routing to the outside plant.
L’ITE ne doit être connecté que sur un réseau PoE sans
routage vers l’ali entation extérieure.
-1-
English
Product Overview
①TOP CASE
②BOTTOM CASE
③LENS
④SUN SHIELD
⑤BOTTOM BOX
⑥TOP BOX
⑦SIDE HOLE
⑧BOTTOM HOLE
⑨HOLE PLUG
⑩ADJUSTMENT SCREW A
⑪ADJUSTMENT SCREW B
⑫ADJUSTMENT SCREW C
⑬MICRO SD CARD SLOT
⑭RESET KEY
Restores the server back to
factory default settin s.
⑮LIVE VIDEO OUTPUT RCA
JACK
-2-
English
Installation
1. Remove the camera from the box. Separate the bottom box
from the top box usin a torx wrench (FIG.1), and remove the
safety cable on the bottom box (FIG.2).
2. Secure the bottom box to anywhere you want by ti htenin the
included truss-head screws (M4.0x25) to the mountin holes
marked “a” on the bottom box (FIG.3 & 4).
3. Firstly, insert the network cable and power cable throu h a pipe
with 1/2" PT (FIG.5), and then secure the pipe to the side hole or
bottom hole (FIG.6, please make sure the connection between
the pipe and the side hole is waterti ht, and the side hole is
facin downwards).
-3-
English
4. Attach the safety cable to the mountin hole on the bottom box
(FIG.7), and connect the network cable and power cable to the
camera’s RJ-45 connector and power input, respectively (FIG.8).
5. Use a torx wrench to lock the top box to the bottom box by
ti htenin the screws (FIG.9 & 10).
-4-
English
6. Adjust the three adjustment screws to turn the camera to the
desired position. Then ti hten the screws (FIG.11–16).
Chan e the Outlet Position for the Network Cable and Power
Cable
1. Loosen the hole plu on the bottom box and secure it to the
side hole (FIG.17).
-5-
English
2. Insert the network cable and power cable throu h bottom
hole on the bottom box (FIG.18), and then connect the
network cable and power cable to the camera’s RJ-45
connector and power input, respectively (FIG.8). For waterti ht
installation, please refer to Installation-3.
System Architectures
For connecting the HD IP cameras to a network, please follow one of
the system architectures below:
(1). Use a DC12V power adapter and a network switch to connect to
the network.
-6-
English
(2). Use a PoE network switch to connect to the network.
(3). Use a PoE power injector and a network switch to connect to
the network.
Emergency Factory Default
To restore the hardware to factory default settin s, please follow
these steps:
1.Press and hold “RESET Key” for 10 seconds and release.
2.Wait for about 40 seconds, and the network LED li ht should turn
off, and o back on a ain.
3.The camera is now restored to factory default settin s, and will
reboot automatically.
4.Search for the IP device usin the IPScan software.
5.Start the IP device via an Internet browser.
6.Enter the default username “admin” and password “pass” to
operate.
-7-
English
NOTE: For your convenience, the IP address will revert to the default
settin of 192.168.0.200.
Before Accessing IP Cameras
Before accessin the IP camera, make sure that the camera’s RJ-45
network, audio, and power cables are properly connected. To set the
IP address, consult your network administrator for an available IP
address. The default IP address for each IP camera is 192.168.0.200.
Users can use the default IP address for verifyin the camera’s
network connection.
Software Requirements
Merit LILIN Universal ActiveX software components are required for
web interface display of JPEG or H.264 Full HD video. When you
lo in to the IP camera by Internet Explorer, the security warnin
dialo box will prompt the installation of the LILIN Universal ActiveX.
Click Install to download it.
Configuring IP Addresses with IPScan Software
To confi ure an IP address usin the IP scan tool, you can copy the
IPScan software from the installation CD, and paste to your
computer. Alternatively, you can execute the IPScan software from
the installation CD, or download the software from the Merit LILIN
website (www.meritlilin.com). To chan e the settin s of the IP
-8-
English
address, subnet mask, ateway, or HTTP port, you can follow the
steps below:
1. Run the IPScan software.
2. Click Refresh. All available devices should be listed in the device
list.
3. Select your device from the list provided.
4. Chan e the IP address, subnet mask, ateway, or HTTP port for
the IP camera.
5. Click Apply to submit the settin s.
6. Click Refresh to verify the settin s.
Configuring IP Addresses via Web Interface
To chan e an IP address via web interface, type the default IP
address (192.168.0.200) in the Internet browser and follow the steps
below:
1. Lo in to the H.264 Full HD IP camera by the default username
“admin” and default password “pass”
2. Click Basic Mode confi uration hyperlink.
3. Click Network->General hyperlink.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Lilin Sicherheitskamera Handbücher
Lilin
Lilin ZHR8182 Bedienungsanleitung
Lilin
Lilin ST1358 series Bedienungsanleitung
Lilin
Lilin Z2R8852AX Bedienungsanleitung
Lilin
Lilin iMEGAPRO LD2122E Bedienungsanleitung
Lilin
Lilin IPR424ESX Bedienungsanleitung
Lilin
Lilin P5 Series Bedienungsanleitung
Lilin
Lilin CMD2182 Bedienungsanleitung
Lilin
Lilin D/N HD IR IP CAMERA Bedienungsanleitung
Lilin
Lilin IPC0122WP3 Bedienungsanleitung
Lilin
Lilin IPC0522 Bedienungsanleitung
Lilin
Lilin CMR6082X Bedienungsanleitung
Lilin
Lilin P2 Series Bedienungsanleitung
Lilin
Lilin PIH-7635DH Series Bedienungsanleitung
Lilin
Lilin IPR722-IVS Bedienungsanleitung
Lilin
Lilin iMegapro IPR7722ESX Bedienungsanleitung
Lilin
Lilin IPD112ESX3 Bedienungsanleitung
Lilin
Lilin PIH-8176/8178 Bedienungsanleitung
Lilin
Lilin CMD2422S Bedienungsanleitung
Lilin
Lilin SP2034 Series Bedienungsanleitung
Lilin
Lilin iMEGAPRO IPR2522ES Bedienungsanleitung
