Lincoln Electric VIKING 3350 Series Bedienungsanleitung

GRAPHICS MAY VARY

Operator’s Manual

VIKINGTM 3350 Series

Auto-Darkening Helmets

with 4C

™

Technology

www.lincolnelectric.com/register

Authorized Service and Distributor Locator:

www.lincolnelectric.com/locator

Save for future reference

Date Purchased

Code: (ex: 10859)

Serial: (ex: U1060512345)

IM10516 | Issue Date Jun-19

TABLE OF CONTENTS Page

SAFETY WARNINGS – READ BEFORE USING 1

HELMET INFORMATION 2

SPECIFICATIONS 3

OPERATING INSTRUCTIONS 4

CARTRIDGE OPERATIONS/FEATURES 5

GRIND BUTTON OPERATION 6

HELMET CARE AND MAINTENANCE 7

SHADE GUIDE SETTINGS 7

CARTRIDGE AND LENS REPLACEMENT 8

TROUBLESHOOTING 9

WARRANTY INFORMATION 10

REPLACEMENT PARTS, OPTIONAL ACCESSORIES 10

SAFETY WARNINGS – READ BEFORE USING

ARC Rays can injure eyes and burn skin

• Before welding, always inspect helmet and filter lens to be sure they are fitted

properly, in good condition and not damaged.

• Check to see that the clear lens is clean and securely attached to the helmet.

• Always wear safety glasses or goggles under the welding helmet and protective

clothing to protect your skin from radiation, burns and spatter.

• Ensure that optical radiation from other welder’s arcs in the immediate area

does not enter in from behind the helmet and auto-darkening filter.

Note: Auto-darkening filters in Lincoln helmets are designed to protect the user against harmful

ultra-violet and infrared rays both in the dark and light states. No matter what shade the filter is

set to, the UV/IR protection is always present.

FUMES AND GASES can be dangerous to your health.

• Keep your head out of fumes.

• Use enough ventilation or exhaust at the arc or both to keep fumes and gases

from your breathing zone and general area.

• When welding with electrodes which require special ventilation such as

stainless or hard facing (see instructions on container or MSDS) or on

lead or cadmium plated steel and other metals or coatings which

produce highly toxic fumes, keep exposure as low as possible and within

applicable OSHA PEL and ACGIH TLV limits using local exhaust or

mechanical ventilation. In confined spaces or in some circumstances,

outdoors, a respirator may be required. Additional precautions are also

required when welding on galvanized steel.

WARNING

Refer to http://www.lincolnelectric.com/safety

for additional safety information.

HELMET INFORMATION

This Auto-Darkening Welding Helmet will automatically change from a light

state (shade 3.5) to a dark state (Shade 5-13) when arc welding starts.

The filter automatically returns to a light state when the arc stops.

Match your welding application to the shade indicated on the shade chart.

(See Page 6)

• Operating temperature: 14°F ~ 131°F (-10°C ~ 55°C).

• Do not use or open the auto-darkening filter if damaged by shock,

vibration or pressure.

• Keep the sensors and solar cell clean. Clean the filter cartridge using a

soapy water solution and soft cloth which should be damp but not

saturated.

This Auto-Darkening Welding Helmet is designed for use with GMAW, GTAW,

MMAW welding, or Plasma Arc and air carbon arc cutting.

The cartridge provides protection from harmful UV and IR radiation, in both

dark and light states.

The cartridge contains four sensors to detect the light from the welding arc,

resulting in the lens darkening to a selected welding shade.

• Do not use solvents or abrasive cleaning detergent.

• If cover lens is spattered or covered with dirt, it should be replaced

immediately.

• Use only replacement parts specified in this manual.

• Do not use the helmet without inside and outside cover lenses properly

installed.

SPECIFICATIONS

Optical Class 1/1/1/1

LCD Viewing Area 95 x 85mm (3.74 x 3.34in.)

Cartridge size 114 x 133mm (4.50 x 5.25in.)

UV/IR Protection Up to Shade DIN 16 at all times

Arc Sensors 4

Light State Shade DIN 3.5

Variable Welding Shades DIN 5 to 13

Shade Control Dial knob - full adjustment

Power Supply Solar cell with battery assist

Low Battery Warning Red Light

Grind Warning Green Light

Battery CR2450 Lithium (1 Required)

Power On/Off Fully automatic

Light to Dark Switching Time 0.00004 sec. (1/25,000 sec.)

Dark to Light Switching Time 0.1 sec. (Short) to 1.0 sec. (Long)

Sensitivity Control

Variable

TIG Rating DC≥2 amps; AC≥2 amps

Operating Temperature 14°F ~ 131°F (-10°C ~ 55°C)

Storage Temperature -4° ~ 158°F (-20°C ~ 70°C)

Total Weight Black 606g (21.37 Oz.)

Graphic 613g (21.62 Oz.)

Compliance(1) ANSI Z87.1, CSA 94.3, EN 379,

AS/NZS 1338.1

OPERATING INSTRUCTIONS

Headgear Adjustment

HEAD SIZE ADJUSTMENT: HEADGEAR TIGHTNESS is adjusted by turning

the Ratchet Knob to the right or left to adjust for the desired head size.

This knob is located at the back of the helmet. HEADGEAR CROWN

ADJUSTMENT is made by adjusting the comfort then placing the strap under

the guide and snapping the pins into the holes to lock securely in place.

TILT: Tilt adjustment is located on the right side of the helmet. Loosen the

right headgear tension knob and push the top end of the adjustment lever

outward until the lever’s Stop Tab clears the notches. Then rotate the lever

forward or back to the desired tilt position. The Stop will automatically

engage again when released locking the helmet into position.

FORE / AFT ADJUSTMENT: Adjusts the distance between the user's face

and lens. To adjust, slide and hold the spring loaded caps upward while mov-

ing the headgear into one of four slotted locations. Once the desired distance

has been achieved let go of the cap and it will return to its resting position

once the adapter is secured in one of the four slots. NOTE: Make sure both

sides are equally positioned for proper orientation.

Crown Adjustment

Fore-Aft

Adjustment

Tilt

Adjustment

Ratchet

Knob

GRIND BUTTON OPERATION

In order to switch the Auto Darkening Filter from a Cutting or Welding Shade

into Grind Mode first locate the silicone button on the left side of the helmet.

After the button has been located press and hold it for 3 seconds. A green

LED on the cartridge should blink every 3 seconds after the button is pressed

to indicate you are in Grind mode. To switch back to the previous Cutting or

Welding shade simply press and hold the button for 3 seconds. Grind mode

is intended for grinding only not for welding.

90°

45°

CARTRIDGE OPERATION/FEATURES

Variable Shade Control

The shade can be adjusted from shade 5 to 8 and 9 to 13 based upon welding

process or application (refer to shade selection chart on page 6). Shade is

adjusted by setting the shade range switch to the proper range, then use the

shade dual scale dial to set the desired shade. The shade range switch and dual

scale dial are located on the ADF cartridge as shown below.

Test Button

Press and hold test to preview shade selection before welding. When released

the viewing window will automatically return to the light state (3.5 Shade).

Sensitivity Knob

Adjust the light sensitivity by turning the SENSITIVITY knob to the left or right as

shown in the figure below.

Turning the knob to the left increases sensitivity

which makes the ADF cartridge more sensitive to light.

When helmet is used

in the presence of excess ambient light or with another welding machine close by,

improved helmet performance can be obtained with a lower setting by turning the

knob to the right to reduce the sensitivity.

Delay Time Knob

This control is designed to protect the welder's eyes from the strong residual rays

after welding. Changing the DELAY

knob will vary the dark to

light time between 0.1 second (S) to

1.0 second (L). The Lsetting is

recommended for high amperage

applications where the weld puddle is

still very bright after the welding arc

has ceased and for situations where

the filter may be temporarily blocked

from seeing the welding arc.

Power

This ADF cartridge is powered by a

replaceable battery and solar power.

The battery is located at the bottom

corner of the ADF cartridge. Replace

battery when LOW BATTERY light

is lit. See the specification chart on

page 3 for type of battery required.

CR2450

DELAY TIME

SHADE

BATTERY

TEST

BATTERY

LOW

GRIND

SENSITIVITY

HI LO

S27978-151

SHADE 9-13SHADE 5 - 8

4/5-8/9-13TM

1/1/1/1/379

CSA Z94.3

Operating Temp.

TM Z87W4/5-8/9-13

-10°C to +55C

Replaceable

Lithium Battery

AS/NZS1338.1

LABS

Shade Range

Switch

Shade Dual

Scale Dial

HELMET CARE AND MAINTENANCE

Cleaning: Clean helmet by wiping with a soft cloth. Clean cartridge surfaces

regularly. Do not use strong cleaning solutions. Clean sensors and solar cells

with soapy water solution and a clean cloth and wipe dry with a lint-free cloth.

Do NOT submerge shade cartridge in water or other solution.

Storage: Store in a clean, dry location.

SHADE GUIDE SETTINGS

If your helmet does not include any one of the shades referenced above, it is

recommended you use the next darker shade.

NT 1

GUIDE FOR SHADE NUMBERS

OPERATION ELECTRODE SIZE ARC MINIMUM SUGGESTED(1)

1/32 in. (mm) CURRENT (A) PROTECTIVE SHADE NO.

SHADE (COMFORT)

Shielded metal arc Less than 3 (2.5) Less than 60 7 –

welding 3-5 (2.5–4) 60-160 8 10

5-8 (4–6.4) 160-250 10 12

More than 8 (6.4) 250-550 11 14

Gas metal arc Less than 60 7 –

welding and flux 60-160 10 11

cored arc welding 160-250 10 12

250-500 10 14

Gas tungsten arc Less than 50 8 10

welding 50-150 8 12

150-500 10 14

Air carbon (Light) Less than 500 10 12

Arc cutting (Heavy) 500-1000 11 14

Plasma arc welding Less than 20 6 6 to 8

20-100 8 10

100-400 10 12

400-800 11 14

Plasma arc cutting (Light)(2)

(2)

(2) Less than 300 8 9

(Medium) 300-400 9 12

(Heavy) 400-800 10 14

Torch brazing – – 3 or 4

Torch soldering – – 2

Carbon arc welding – – 14

PLATE THICKNESS

in. mm

Gas welding

Light Under 1/8 Under 3.2 4 or 5

Medium 1/8 to 1/2 3.2 to 12.7 5 or 6

Heavy Over 1/2 Over 12.7 6 or 8

Oxygen cutting

Light Under 1 Under 25 3 or 4

Medium 1 to 6 25 to 150 4 or 5

Heavy Over 6 Over 150 5 or 6

(1) As arule of thumb, start with a shade that is too dark, then go to a lighter shade which gives sufficient view of the weld zone without going

below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs

the yellow or sodium line the visible light of the (spectrum) operation

(2) These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the

workpiece.

Data from ANSI Z49.1-2005

CARTRIDGE AND LENS REPLACEMENT

Replacing Front Clear Cover Lens: Replace the front cover lens if it is

damaged. Remove ADF holder assembly per Figure 1. Remove front cover lens

from helmet assembly. Carefully remove gasket from cover lens. Install new

cover lens into gasket and assemble to helmet shell. Make sure to assemble

cover lens and gasket into helmet shell the same way as it was removed.

Replacing Inside Clear Lens: Replace the inside clear lens if it is damaged.

Place your fingernail in recess above cartridge view window and flex lens

upwards until it releases from edges of cartridge view window.

Change the Shade Cartridge: Remove ADF holder assembly from helmet shell.

See figure 1 for removal. Flex bottom end of the ADF holder to allow for ADF

cartridge to be removed from frame. Install new ADF cartridge into frame per

figure 2 below. Make sure that the ADF cartridge is inserted in ADF holder

correctly as shown. Install ADF holder assembly into helmet shell.

INSTALLING AN AFTERMARKET MAGNIFYING LENS:

Simply slide the magnifying lens into the short rail located on the sides of ADF

holder per Figure 3. Shade cartridge must be removed from ADF holder to install

magnifying lens.

Figure 3

Figure 1 Figure 2

Andere Handbücher für VIKING 3350 Series

Inhaltsverzeichnis

Sprachen:

Andere Lincoln Electric Schweißzubehör Handbücher

Lincoln Electric

Lincoln Electric X-Tractor 3A Bedienungsanleitung

Lincoln Electric

Lincoln Electric SVM154-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric IM10196 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Metalshield MC-715 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Outershield Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER FEED 10M Bedienungsanleitung

Lincoln Electric

Lincoln Electric Miniflex Bedienungsanleitung

Lincoln Electric

Lincoln Electric Activ8X Bedienungsanleitung

Lincoln Electric

Lincoln Electric Pyrotome SE Montageanleitung

Lincoln Electric

Lincoln Electric US-M1800-LS Bedienungsanleitung

Lincoln Electric

Lincoln Electric GRAPHICS MAY VARY Bedienungsanleitung

Lincoln Electric

Lincoln Electric SLIDEMATIC S50E Montageanleitung

Lincoln Electric

Lincoln Electric LN-7 Bedienungsanleitung

Lincoln Electric

Lincoln Electric ZIPLINE BOOM PACKAGE Bedienungsanleitung

Lincoln Electric

Lincoln Electric LN-35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric SVM176-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric CAN-M568 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER FEED 10M Bedienungsanleitung

Lincoln Electric

Lincoln Electric IM573 Gebrauchs- und Pflegehandbuch

Lincoln Electric

Lincoln Electric CAN-CW800-C Bedienungsanleitung

Lincoln Electric

Lincoln Electric 900 Bedienungsanleitung

Lincoln Electric

Lincoln Electric Magnum PRO 250 LX Bedienungsanleitung

Lincoln Electric

Lincoln Electric AUTO-DARKENING HELMET IM10001 Bedienungsanleitung

Lincoln Electric

Lincoln Electric LN-10 ZIPLINE BOOM PACKAGE Bedienungsanleitung

Beliebte Schweißzubehör Handbücher anderer Marken

Cornwell Tools

Cornwell Tools MMWC1 Bedienungsanleitung

Dohle

Dohle ExOn2A Bedienungsanleitung

Nederman

Nederman Fume Eliminator FE 840/2500/P150 Bedienungsanleitung

3M Speedglas 9100 Series Bedienungsanleitung

Miller Electric

Miller Electric OM-842 Bedienungsanleitung

Miller

Miller A-200 Series Bedienungsanleitung

Abicor Binzel

Abicor Binzel ABIMIG WT Series Bedienungsanleitung

Miller

Miller MIGmatic M-25 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT3 Reamer Bedienungsanleitung

Abicor Binzel

Abicor Binzel xFUME PRO Bedienungsanleitung

Sealey

Sealey SR20.V2 Bedienungsanleitung

iWeld

iWeld NORED EYE Bedienungsanleitung

Sthor

Sthor 74483 Bedienungsanleitung

Leister

Leister TWINNY T7 Bedienungsanleitung

Miller

Miller I-22 CE Bedienungsanleitung

LAHTI PRO

LAHTI PRO L1540400 Bedienungsanleitung

Tregaskiss

Tregaskiss TOUGH GUN TT4E Bedienungsanleitung

Miller Electric

Miller Electric A1D-4RV Bedienungsanleitung