Lincoln Electric POWER MIG210S Bedienungsanleitung

THANKS FOR PURCHASING OUR PRODUCT

POWER MIG210S

Inverter MIG/MAG/MMA Semi-auto ARC Welding Machine

Operation Manual

(Read the manual carefully before installation ,operation and maintenance)

Advanced Product

OWER IG210S

SAFETY PRECAUTIONS

Follow these precautions carefully. Improper use of any welder

can result in injury or death.

1. ONLY CONNECT WELDER TO A POWER SOURCE FOR WHICH IT WAS DESIGEND.

The specification plate on the welder lists this information. When welding outdoors only use an

extension cord intended for such use.

2. ONLY OPERATE WELDER IN DRY LOCATIONS and on cement or masonry floor. Keep

area clean and uncluttered.

3. KEEP ALL COMBUSTIBLES AWAY FROM WORK SITE.

4. DO NOT WEAR CLOTHING THAT HAS BEEN CONTAMINATED with grease or oil.

5. KEEP CABLES DRY AND FREE FROM OIL AND GREASE and never coil around

shoulders.

6. SECURE WORK WITH CLAMPS or other means; don't over reach when working.

7. NEVER STRIKE AN ARC ON A COMPRESSED GAS CYLINDER

8. DON'T ALLOW THE INSULATED PORTION OF THE ELECTRODE HOLDER TO TOUCH

THE WELDING GROUND WHILE CURRENT IS FLOWING.

9. SHUT OFF POWER AND UNPLUG MACHINE WHEN REPAIRING OR ADJUSTING.

Inspect before every use. Only use identical replacement parl.

10. FOLLOW ALL MANUFACTURER'S RULES on operating switches and making

adjustments.

11. ALWAYS WEAR PROTECTIVE CLOTHING when welding . This includes: long sleeved

shirt(leather sleeves), protective apron without pockets, long protective pants and boots. When

handing hot materials, wear asbestos gloves.

12. ALWAYS WEAR A WELDER'S HELMET WITH PROTECTIVE EYE PIECE when welding.

Arcs may cause blindness. Wear a protective cap underneath the helmet.

13. WHEN WELDING OVERHEAD, BEWARE OF HOT METAL DROPPINGS. Always protect

the head, hand, feet and body.

14. KEEP A FIRE EXTINGUISHER CLOSE BY AT ALL TIMES.

15. DO NOT EXCEED THE DUTY CYCLE OF THE MACHINE. The rated cycle of a welding

machine is the percentage of a ten minute period that the machine can operate safely at a given

output setting.

16. KEEP ALL CHILDREN AWAY FROM WORK AREA. When storing equipment, make sure

it is out of reach of children.

17. GUARD AGAINST ELECTRIC SHOCK. DO not work when tired. Do not let body come

In'contact with grounded surfaces.

Prolegomenon

We do very appreciated for your selecting our products.

This kind of welding power Model POWERMIG210S is taken foreign advanced technology to

develop and manufacture the new generation inverter integrated controlling Semi-auto MIG/MAG ARC

and MMA Welding machine.

It can be composed the POWERMIG210S MIG/MMA multi function Welding system equipped

with wire feeder and welding gun .It has many characteristic such as easy Arc starting .good Arc

springiness .adjustable arc thrusting ,low splash,good welding form ,easy welding operation,wide range

and electricity save.

The MIG/MMA multi function welding machine model POWERMIG210S is advanced welding

machine and it can be compared with foreign products.

This operation manual can help you for the machine installation, operation and maintenance

correctly and safely.Pay attention to the points as following.

．Installation of the power cord. Be grounded correctly.

. Don't put sundries under the welder.Otherwise it will affect the heat released.

. Installation for the positive and negative cable of the power output.

. Welding voltage selection

. Welding current selection (speed of wire feeder)

. Selection of Arc thrusting(arc force)

The amendment right and the explanation right of the manual belonging to my company.We have

no special notice if the manual is amended.

1. Main characteristic and suitable range

This kind of welding power Model POWERMIG210S is taken foreign advanced technology to

develop and manufacture the new generation inverter integrated controlling Semi-auto MIG/MAG Arc

welding machine.It makes use of the import key parts such as Siemens IGBT module of Germany,alloy

magnetic core and the resume diode module of America. It has the perfect performance of high quality ,

good reliability, quick speed of welding current, steady welding process,low splash and good welding

form . Anyway,It becomes the welding very easy.

1.1 Structure of the POWERMIG210S multi function welding machine

a.The name of the model

POWERMIG210S

max welding current

MIG/MMA multi Arc welding machine

Model improvement

b. Composing of the product

This product is composed by three parts as following

★

Power source(POWERMIG210S)

★

welding gun

1.2 Suitable range of the POWERMIG210S

★

Suitable material: low-carbon steel, stainless steel

★

Thickness of the material:low-carbon steel and stainless:more than 0.5mm

★

Suitable position:all positions

★ φ

Suitable wire : 0.6,0.8,0.9,1.0solid wire/flux cord wire.

1.3 Characteristic of POWERMIG210S

★

Wide output current 30-200A: 0.6 -----------30-100A

0.8------------50-200A

1.0------------80-200A

★

Steady welding process,low splash,easy control,good welding form.

★

High efficiency: 200A/24V the duty cycle is 35%

160A/22V the duty cycle is 60%

130A/20.5V the duty cycle is 100%

continuous wire feed,the max speed of wire feed is 15m/min

★

Low starting of wire feed

★

Preset the welding voltage :Preset the welding current to read the welding

criterion easy.

★

Adjusting the arc thrusting: Control the splash and steady arc.

★

Strong resistance for the fluctuate of the electricity

2.Main technical Data :

★

Input Voltage 1~220V/230V/240V ; 50/60Hz

★

Rated Input current 36 A

★

Rated Input power 7.8KVA

★

No-load Voltage 70V

★ ± ±

Voltage adjusting Range 14 3V~26 3V

★

Current output Range 30~200A (MIG/MAG)

10~175A(MMA)

★ ，，

Suitable wire 0.6 , 0.8 0.9 1.0

★

Duty cycle 200A/24V the duty cycle is 35%

160A/22V the duty cycle is 60%

130A/20.5V the duty cycle is 100%

★ η≥

Efficiency 0.85

★ λ

Power factor =0.83

★

Insulation class F

★

Protection class of shell fan cooling

3.Function

3.1 Adjusting function for the welding voltage and welding current

3.1.1 POWERMIG210S supply the adjusting range at MIG/MAG as following,

± ±

Welding voltage : 14V 3V~26V 3V use the voltage adjusting knob

Welding current : 30A~200A use the current adjusting knob

3.1.2 POWERMIG210Ssupply the adjusting range at MMA as following,

Welding current : 10A~175A use the welding current knob on the panel.

3.2 Adjusting function of the Arc thrusting

It has the important function to select the proper Arc thrusting for improvement of the welding

line ,control the welding splash and the steady Arc. Normally,.

If the thrusting is low ,the arc is soft and splash .

If the thrusting is high,the arc is strong and high splash.

Use the arc thrusting continuously by the control knob on the front panel of POWERMIG210S.

3.3 Recycle function

We design the function to settle two problems.

1) Control the diameter of the wire ball at the end of wire .

2) Prevent the wire into the pool after the Arc stopping.

4. Indicating and warning on the POWERMIG210S control panel

4.1 Indicating and adjusting

4.1.1 Voltage /MMA arcforce Display meter

、

a The meter on the front panel can indicate the actual welding voltage or preset MIG voltage.

The indicating number has the precision of 0.1V .The meter indicates the preset during no welding.

、

b display MMA arcforce

4.1.2 Current indicating

The current indicating meter on the front panel indicates the actual welding current during the

，

welding indicates the preset current during no welding.

4.1.3 Power indicating

If the indicating light is on the control circuit connects the power already.

4.1.4 unit of post flow time

（）

4.1.5 unit of wire speed no use

4.1.6 unit of current

13 14

4.1.7 MIG/MMA Process Selector

Each icon graphically repre-sents each process for rapid eye acquisition when changing processes.

The top function represents MIG. The bottom function represents MMA.

4.1.8 unit of voltage

4.1.9 Amp/Wire Speed Adjustment Knob

For Stick function, this adjusts the amps. For MIG opera-tion,the amps are directly tied to the wire

speed feed. Increasing the speed increases the amps and vice versa. While the unit displays in

m/min for MIG operation, a change in this control also results in a change of amps.

4.1.10 Duty Cycle/Overcurrent Warning.

When the duty cycle has been exceeded or an overcurrent, condition has occurred, the L.E.D. will

light. Allow the unit to cool while running until the light goes off or for 10 minutes before resetting the

welder. If condition persists check for loose wires or voltage supply problems.

4.1.11 MIG Wave Form Control.

Varies the slope of the current rise time between during short circuit MIG operation. This affects

the actual point where the current has risen sufficiently to burn back the wire.

4.1.12 Memory chanel LED

4.1.13 CH(chanel)/SAVE Process Selector

led of the"CH(chanel)" lighting when you press or press "3 s" until the led of "SAVE" you have

saved the data.

4.1.14 MIG post flow Process Selector

4.1.15 2T/4T Torch Switch Selector

The torch trig-ger function is designed to operate for MIG functions. To operate in 2T mode, the

“ ”

trigger on the MIG torch should be simply held down. The 4T function operates as a torch latch in

MIG mode that locks the MIG torch on without needing to hold the trigger. To operate 4T in the MIG

mode, simply press the torch trigger and hold it down until the arc starts. To lock it on, release the

trigger and weld without hold-ing the trigger down. To stop, the trigger must be pressed again, and then

released after 1-2 seconds.

4.1.16 MIG Volt/ MMA Arc Force Control/MIG post flow.

In each mode, the function of the control changes. In the MIG mode, the control is used to adjust

the arc voltage. In Stick mode, the control is used to vary the automatic arc force current re-sponse.

“ ”

When used for stick welding the arc force is also known as dig . When welding in stick mode, the

current is increased as the volts fall off due to a short arc length. This helps maintain the arc by

providing more watt-age.

4.1.17 Wire Alloy Selector.

Select your wire type according to the basic categories of Fe (Steel), Ss (Stainless Steel) or Al (

Aluminum). This input must be made to properly use the Synergic function to automatically adjust the

Volts needed to weld at the selected wire speed.

4.1.18Wire Diameter/ALT selector:

Select your wire diameter according of the type wire you are using. Selecting the correct wire

diameter is critical to optimum Synergic function of the welder, automatically compensating the voltage

“

while the wire speed is adjusted. For alternate full manual control of the welder to function in

”

normal mig mode, select ALT. This will allow for full, independent control of MIG wire speed and

voltage.

5.Safe and installation caution

Read the safe caution before installation and operation .It come down to the high voltage

electricity,electric Arc and high temperature splash.So keep the safe regulation ,operate the machine

properly,avoid the danger of electricity and high temperature arc.

★

Check if any damage ot out looking ot the welder.

★

Confirm the capacity:more than 30A.

★

Power source is grounded,diagram 6

★

Prohibit the combustible goods in the welding locale.

★

There is fire proof measure in the welding locale with favorable ventilated condition.

★

There is smoke discharge system if the welding is operated inside the house in order to keep

the safety of workers.

★

The welding operator must be professional workers.

★

The operator must be fitted with safe accessories .Such as safe shoes,gloves,cover,welding

make and welding dress etc.

6. Explanation of installation

6.1 MIG/MAG welding

put the switch "7" MIG/MMA SWITCH into "MIG"

★ Check the products according to the packing list when open the package.

★

Grounded protection.Attached the diagram 6

The power source is 220~240Vac/(50~60Hz) .The yellow/green double cable is grounding cable.

Be sure to connect the yellow/green double cable into the grounding connection in the welding locale .

Another way is selecting the M8 bolt on the back on the machine and connect the grounding as the

diagram as following.

★Install the welding gun on the front panel and screw the welding gun ,then lock the bolt.

★ Connect the gas pipe with the gas bottle according to the locale conditions. Check the air proof

conditions to ensure the good airproof.

CO2

flow meter

yellow/green double cable

diagram 6

air breaker

back panel.

fan

gasinlet

230V

switch for power

power FUSE

TO INSTALL WIRE:

1. Loosen top idler tensioner, rotating counter-clockwise

2. Flip tensioners down, releasing top drive rolls.

3. Raise top drive rolls.

4. Inspect the drive roll to make sure that the groove size matches the wire diameter. Reversal of the lower roller may be

necessary. To reverse the roller, remove the thumb screw securing the drive roll. Pull the drive roll off, and flip the drive roll over.

Reassemble and tighten roller. If larger roller is needed, contact Everlast.

5. Thread straightened wire over grooves in lower drive roll, fully through until it begins to start threading into the gun section.

Lower upper drive rolls onto lower drive roll, keeping wire in the groove.

6. Raise tensioner back into place. Tighten slightly so wire will feed. Notice markings on tensioner for future reference.

7. Hold torch straight out as possible. Press gun trigger to feed wire until the wire exits the end of the torch.

8. Adjust tensioner clockwise until drive rolls will not slip when wire comes into contact with surface and the wire will curl up on

end. Remember to keep wire away from metal that is attached to the work clamp clamp to prevent the wire from arcing

diagram 7

working piece

welding gun(AK15)

front panel.

GAS

SIDE VIEW

front panel.

working piece

welding gun(AK15)

NO GAS

SYNERGIC AND BASIC MIG OPERATION

Synergic vs. Manual Setup and Operation

How Synergic MIG operates:

The Synergic function of the MIG (200S) component allows the user to only need to use the wire

feed speed control to make the unit operate. The welder is programmed to automatically adjust the

voltage based off the users input of wire diameter, and filler metal type when the wire speed is increased

or decreased by turning the wire speed adjustment knob. While in the Synergic mode, the user can make

“ ”

manual adjustment to fine tune the voltage if he chooses by turning the voltage up or down after

adjusting the wire feed speed. If the wire speed is readjusted after manual adjustment to voltage is made,

the unit defaults to the synergic mode again, and voltage is once again adjusted automatically. The

welder may be used in full Manual mode, with independent control of the wire feed speed by simply

selecting ALT on the wire diameter selector. Settings will not be saved when the unit cycles off and

back on and will default to factory settings. If stepping away briefly it is best to keep the unit on, or the

settings will not remember the last settings if it is turned off.

How to setup the Synergic and Manual functions:

1. Turn unit on. Wait for it to go through the power up cycle.

2. Select the MIG icon with the Process Selector button.

3. Select the wire diameter of the wire being used. Selecting ALT defaults unit to full manual

mode. Aluminum will default to .040" & ALT. so that the wire will not jam or birds nest while feeding.

4. Select the filler wire type. Fe= Steel, Al= Aluminum, SS= Stainless Steel.

5. Select 2T or 4T function. 2T is simply press and hold the torch trigger to start and activate the

torch. 4T re-quires the trigger to be pressed to start the arc. Once started, the trigger should be released

to weld. The trigger should once again be pressed, held briefly and then released to terminate the arc

when ready.

0.6

0.8

0.9

1.0

Inhaltsverzeichnis

Andere Lincoln Electric Schweißsystem Handbücher

Lincoln Electric

Lincoln Electric INVERTEC V320-T AC/DC Bedienungsanleitung

Lincoln Electric

Lincoln Electric BULLDOG TM 140 IM10005 Bedienungsanleitung

Lincoln Electric

Lincoln Electric SP20/MP2 Series Montageanleitung

Lincoln Electric

Lincoln Electric POWER WAVE IM846-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric AC-235 Bedienungsanleitung

Lincoln Electric

Lincoln Electric K206 FLUX IM548 Bedienungsanleitung

Lincoln Electric

Lincoln Electric RED-D-ARC LN-25 PRO EXTREME Bedienungsanleitung

Lincoln Electric

Lincoln Electric SP 170-I Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWERWAVE IM762-C Bedienungsanleitung

Lincoln Electric

Lincoln Electric EAGLETM 10 Bedienungsanleitung

Lincoln Electric

Lincoln Electric COUGAR K2704-2 Bedienungsanleitung

Lincoln Electric

Lincoln Electric AC-225 Bedienungsanleitung

Lincoln Electric

Lincoln Electric AIR VANTAGE 500 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V145-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric LN-9 SVM127-A Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V160-S Bedienungsanleitung

Lincoln Electric

Lincoln Electric MAGNUM PRO AL G450W Bedienungsanleitung

Lincoln Electric

Lincoln Electric FRONTIER Bedienungsanleitung

Lincoln Electric

Lincoln Electric Lincolnweld 980 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Lincoln Electric

Lincoln Electric RED-D-ARC PM 255 Bedienungsanleitung

Lincoln Electric

Lincoln Electric LINC 405 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER-ARC SVM103-C Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung

Kipor

Kipor KDE180XW Bedienungsanleitung

OrienTek

OrienTek T40 Bedienungsanleitung