Lindab AGHR-100 Bedienungsanleitung

USER’S MANUAL

• AGHR-100

• ASHR-100

• AGHR-130

• ASHR-130

• AGHR-150

• ASHR-150

SINGLE-ROOM

REVERSIBLE ENERGY

REGENERATION VENTILATOR

Safety requirements 3

Purpose 5

Delivery set 5

Main technical parameters 6

Design and operating logic 11

Mounting and set-up 13

Connection to power mains 20

Ventilator control 23

Maintenance 25

Troubleshooting 27

Storage and transportation regulations 27

Manufacturer's warranty 28

Acceptance certicate 29

Seller information 29

Installation certicate 29

Warranty Card 30

CONTENTS

• Read the user’s manual carefully prior to installing and operating the unit.

• Full the user’s manual requirements as well as the provisions of all the applicable local and national construction, electrical and

technical norms and standards.

• The warnings contained in the user’s manual must be considered most seriously since they contain vital personal safety information.

• Failure to follow the rules and safety precautions noted in this user’s manual may result in an injury or unit damage.

• After a careful reading of the manual, keep it for the entire service life of the unit.

• While transferring the unit control the User’s manual must be turned over to the receiving operator.

Symbol legend:

WARNING!

DO NOT!

SAFETY REQUIREMENTS

The user’s manual consisting of the technical details, operating instructions and technical specication applies to the installation and

mounting of the single-room energy regeneration reversible ventilator (hereinafter «the unit» as mentioned in the «Safety Requirements» and

«Manufacturer’s Warranty» sections as well as in warnings and information blocks).

UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS

• Disconnect the unit from power mains prior

to any installation operations. • The unit must be grounded!

• Do not lay the power cable of the unit in

close proximity to heating equipment.

• While installing the unit follow the safety

regulations specic to the use of electric

tools.

• Do not change the power cable length at

your own discretion.

• Do not bend the power cable.

• Avoid damaging the power cable.

• Do not put any foreign objects on the power

cable.

• Unpack the unit with care.

• Do not use damaged equipment or cables

when connecting the unit to power mains.

• Do not operate the unit outside the

temperature range stated in the user’s

manual.

• Do not operate the unit in aggressive or

explosive environments.

• Do not touch the unit controls with wet

hands.

• Do not carry out the installation and

maintenance operations with wet hands.

• Do not wash the unit with water.

• Protect the electric parts of the unit against

ingress of water.

UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS

• Do not allow children to operate the unit. • Disconnect the unit from power mains prior to

any technical maintenance.

• Do not store any explosive or highly ammable

substances in close proximity to the unit.

• When the unit generates unusual sounds,

odour or emits smoke disconnect it from

power supply and contact the Seller.

• Do not open the unit during operation. • Do not direct the air ow produced by the unit

towards open ame or ignition sources.

• Do not block the air duct when the unit is

switched on.

• In case of continuous operation of the unit

periodically check the security of mounting.

• Do not sit on the unit and avoid placing

foreign objects on it. • Use the unit only for its intended purpose.

The unit is designed to ensure continuous mechanical air exchange in houses, oces, hotels, cafes, conference halls and other utility and

public spaces.

The ventilator is equipped with a ceramic regenerator that enables supply of fresh ltered air heated by means of extract air heat energy

regeneration.

The ventilator is designed for through-the-wall mounting.

The telescopic ventilator design enables its installation in the walls with various thickness, see the table below:

Wall thickness Ventilator model

300 mm - 570 mm (11 13/16’’ - 22 7/16”) • AGHR-100

• ASHR-100

250 mm - 470 mm (9 13/16’’ - 18 1/2”)

• AGHR-130

• ASHR-130

• AGHR-150

• ASHR-150

The ventilator is rated for continuous operation always connected to power mains.

Transported air must not contain any ammable or explosive mixtures, evaporation of chemicals, sticky substances, brous materials,

coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust, pathogenic

germs).

Name Number

Ventilator 1 item

Fastening set 1 item

Remote control 1 item

User's manual 1 item

Packing box 1 item

PURPOSE

THE UNIT MAY NOT BE OPERATED BY CHILDREN OR PERSONSWITH REDUCED PHYSICAL, MENTAL OR SENSORY

CAPACITIES, OR LACKING THE APPROPRIATE TRAINING.

THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED PERSONNEL AFTER THE

APPROPRIATE BRIEFING.

THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED ACCESS BY UNATTENDED

CHILDREN.

DELIVERY SET

The ventilator is designed for indoor application with the ambient temperature ranging from -20°C (-4 °F) up to +50°C (+122 °F) and relative

humidity up to 80%.

The ventilator is rated as a class I electric appliance.

Ingress Protection (IP) rating from solid objects and liquids IP 24.

The ventilator design is regularly improved, so some models may slightly dier from those ones described in this manual.

300-570

(11 ⁄"-22 ⁄")

133

(5 ¼")

(1 ⁄")

260

(10 ¼")

240

(

9 ⁄"

)

205

( 8 ⁄")

107

4 ⁄"

103

4 ⁄"

107

4 ⁄"

103

4 ⁄"

300-570

(11 ⁄"-22 ⁄")

133

(5 ¼")

(1 ⁄")

260

(10 ¼")

240

(

9 ⁄"

)

165

( 6 ½")

VENTILATOR OVERALL DIMENSIONS, MM INCHES

ASHR-100

MAIN TECHNICAL PARAMETERS

AGHR-100

120-300

(4 ¾"-11 ⁄")

(2 ¼")

144

(5 ⁄")

250-470

(9 ⁄"-18 ½")

133

(5 ¼")

(2 ¼")

300 (11 ⁄")

300

(11 ⁄")

310 (12 ⁄")

260

(10 ¼")

280

(11")

213

( 8 ⁄")

213

( 8 ⁄")

132

5 ⁄"

128

5 ⁄"

250-470

(9 ⁄"-18 ½")

133

(5 ¼")

3 1/8"

(3 ⁄")

300

(11 ⁄")

280

(11")

240

( 9 ⁄")

240

( 9 ⁄")

120-300

(4 ¾"-11 ⁄")

(3 ⁄")

144

(5 ⁄")

300 (11 ⁄")

310 (12 ⁄")

260

(10 ¼")

132

5 ⁄"

128

5 ⁄"

132

5 ⁄"

128

5 ⁄"

132

5 ⁄"

128

5 ⁄"

120-300

(4 ¾"-11 ⁄")

(2 ⁄")

144

(5 ⁄")

250-470

(9 ⁄"-18 ½")

133

(5 ¼")

(2 ⁄")

300 (11 ⁄")

300

(11 ⁄")

310 (12 ⁄")

260

(10 ¼")

280

(11")

213

( 8 ⁄")

213

( 8 ⁄")

157

6 ⁄"

153

250-470

(9 ⁄"-18 ½")

133

(5 ¼")

(3 ⁄")

300

(11 ⁄")

280

(11")

240

( 9 ⁄")

157

6 ⁄"

153

157

6 ⁄"

153

120-300

(4 ¾"-11 ⁄")

(3 ⁄")

144

(5 ⁄")

300 (11 ⁄")

310 (12 ⁄")

260

(10 ¼")

157

6 ⁄"

153

240

( 9 ⁄")

ASHR-130

ASHR-150

AGHR-130

120-300

(4 ¾"-11 ⁄")

(2 ⁄")

144

(5 ⁄")

250-470

(9 ⁄"-18 ½")

133

(5 ¼")

(2 ⁄")

300 (11 ⁄")

300

(11 ⁄")

310 (12 ⁄")

260

(10 ¼")

280

(11")

213

( 8 ⁄")

213

( 8 ⁄")

157

6 ⁄"

153

250-470

(9 ⁄"-18 ½")

133

(5 ¼")

(3 ⁄")

300

(11 ⁄")

280

(11")

240

( 9 ⁄")

157

6 ⁄"

153

157

6 ⁄"

153

120-300

(4 ¾"-11 ⁄")

(3 ⁄")

144

(5 ⁄")

300 (11 ⁄")

310 (12 ⁄")

260

(10 ¼")

157

6 ⁄"

153

240

( 9 ⁄")

AGHR-150

VENTILATOR TECHNICAL DATA

AGHR-100, ASHR-100

Speed I II III

Supply Voltage, 50-60 Hz [V] 1~100-230

Air Capacity [m3/h] (CFM) 7 (4) 15 (9) 24 (14)

Power [W] 3,50 3,95 5,32

Current [A] 0,023 0,026 0,036

RPM [min-1] 1190 1330 2420

Noise Level, 1 m [dB(A)] (Sones) 31 (0,9) 35 (1,3) 43 (2,5)

Noise Level, 3 m [dB(A)] (Sones) 22 (0,4) 25 (0,5) 33 (1,1)

Outdoor noise attenuation [dB(A)] (Sones) 16 (0,4)

Heat Recovery Eciency up to 85%

AGHR-130, ASHR-130

Speed I II III

Supply Voltage, 50-60 Hz [V] 1~100-230

Air Capacity [m3/h] (CFM) 10 (6) 20 (12) 30 (18)

Power [W] 3,93 4,39 5,10

Current [A] 0,023 0,026 0,032

RPM [min-1] 745 1075 1670

Noise Level, 1 m [dB(A)] (Sones) 27 (0,6) 32 (1,0) 38 (2,0)

Noise Level, 3 m [dB(A)] (Sones) 18 (0,4) 23 (0,5) 28 (0,7)

Outdoor noise attenuation [dB(A)] (Sones) 17 (0,4)

Heat Recovery Eciency up to 90%

VENTILATOR TECHNICAL DATA

AGHR-150, ASHR-150

Speed I II III

Supply Voltage, 50-60 Hz [V] 1~100-230

Air Capacity [m3/h] (CFM) 14 (8) 28 (16) 54 (32)

Power [W] 3,80 3,96 5,61

Current [A] 0,024 0,026 0,039

RPM [min-1] 610 800 1450

Noise Level, 1 m [dB(A)] (Sones) 22 (0,4) 29 (0,7) 32 (1,0)

Noise Level, 3 m [dB(A)] (Sones) 13 (0,2) 20 (0,4) 23 (0,5)

Outdoor noise attenuation [dB(A)] (Sones) 18 (0,4)

The ventilator consists of the telescopic air duct with an adjustable length regulated by position of the inner air duct inside the outer air

duct, the ventilation unit and the ventilation hood.

Two lters and the ceramic regenerator are located in the inner duct of the telescope.

The lters are designed to purify supply air and prevent foreign object ingress to the regenerator and the fan.

The ceramic regenerator uses extract air heat energy to warm up supply air ow.

The regenerator is equipped with a pull cord inside to facilitate its withdrawal from the ventilator.

The regenerator is heat insulated with a specially designed insulating material.

The ventilation unit must be installed on inner side of the wall. The ventilation unit is equipped with automatic shutters that shut the air

duct o during the ventilator standby and prevent air back draft.

The ventilation hood must be installed on the outer wall side. It is used for directed air discharge and prevention of ingress of water and

other objects to the ventilator.

VENTILATOR DESIGN

Outer air duct

Outer part of the

telescopic air duct.

Inner air duct

Inner part of the tele-

scopic air duct.

Ventilation unit

Is used to generate air ow by means of

the fan. The decorative grille protects the

fan against ingress of foreign objects

from the premises. The ventilation unit is

equipped with automatic shutters open-

ing when the ventilator is on and clos-

ing when it is o, thus preventing back

air ow.

Outer ventilation hood

Prevents direct water and foreign objects

ingress to the ventilator.-

ASHR-100

AGHR-130

ASHR-130

AGHR-150

ASHR-150

Filter

Designed to clean supply air

ow and prevent dust and for-

eign objects ingress to the venti-

lator. The lters prevent regener-

ator soiling.

Ceramic regenerator

Provides extract air heat

energy regeneration to

warm up supply air ow.

Mounting plate

A mounting plate for installation

the ventilation unit on the wall

and connecting the ventilator to

power supply.

AGHR-100

что ставить

DESIGN AND OPERATING LOGIC

VENTILATOR OPERATING MODES

The ventilator has four ventilation modes:

• Natural air supply - the automatic shutters are opened, the fan does not run

• Supply - the ventilator supplies fresh air to the premise no matter of CN7 jumper position.

• Ventilation — the ventilator operates in permanent supply or extract mode at set speed depending on CN7 jumper position.

• Regeneration - the ventilator operates in reversible mode with heat and humidity regeneration.

CYCLE I

CYCLE II

-10 °С

+20 °С

+17 °С

-7 °С

In Regeneration mode the ventilator operates in two cycles, 70 seconds each.

Cycle I. Warm stale air is extracted from the room. As it ows through the regenerator, it heats and moisturizes the regenerator, transferring

up to 90% heat energy. In 70 seconds as the ceramic regenerator gets warmed the ventilator is switched to supply mode.

Cycle II. Fresh intake air from outside ows through the ceramic regenerator and absorbs accumulated moisture and heat up to the room

temperature. In 70 seconds as the ceramic regenerator gets cooled down, the ventilator is switched into extract mode and the cycle is

renewed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lindab Lüfter Handbücher

Lindab

Lindab LTDP Bedienungsanleitung

Lindab

Lindab Premax I-60 Bedienungsanleitung

Lindab

Lindab LAD Benutzerhandbuch

Lindab

Lindab Pascal LCC Series Bedienungsanleitung

Lindab

Lindab GTI Series Benutzerhandbuch

Lindab

Lindab Versio-H Bedienungsanleitung

Lindab

Lindab LCR-1 Bedienungsanleitung

Lindab

Lindab Plexus Bedienungsanleitung

Lindab

Lindab Premum Series Bedienungsanleitung

Lindab

Lindab Versio H Bedienungsanleitung

Lindab

Lindab Integra Series Bedienungsanleitung

Lindab

Lindab AGF Series Bedienungsanleitung

Lindab

Lindab PC6 Benutzerhandbuch

Lindab

Lindab WH45 Series Bedienungsanleitung

Lindab

Lindab GD Benutzerhandbuch

Lindab

Lindab Premax Installations- und Benutzerhandbuch

Lindab

Lindab FORMO PKA Bedienungsanleitung

Lindab

Lindab SRF Handbuch

Lindab

Lindab MBB Gebrauchsanweisung

Lindab

Lindab LCFV Bedienungsanleitung

Lindab

Lindab Versio-V Bedienungsanleitung

Lindab

Lindab OLC Bedienungsanleitung

Lindab

Lindab Plexus Series Bedienungsanleitung

Lindab

Lindab Plexus Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung