Linear Power 992IQ Programmierhandbuch
MODEL 992IQ
(1995-MSRP $349.00)
OWNER'S MANUAL AND
INSTALLATION GUIDE
INTRODUCTION
Latest technology, high sound quality, powerful delivery, and LINEAR POWER
reliability all describe LINEAR POWER low profile amplifiers. With new "IQ"
circuitry, their value increases. Versatile capabilities such as stereo, mono or
mixed stereo/mono operation and 2 ohm capability make these amplifiers
extremely desirable as the foundation of a multi-amplifier system.
TECHNICAL DESCRIPTION
The "IQ" series amplifiers are low profile inverted channel ("I") amplifiers. A
quiet turn on circuit ("Q") has been added for improved performance. The
amplifier design incorporates an unregulated power supply for increased dynamic
headroom efficiency. The output stages of the 992IQ amplifier will deliver a
significant increase in power into 2-ohm stereo loads. Amplifier reliability is
accomplished by the amplifier operation level being set at approximately 50% of
output transistors' rated power handling, even at this lower impedance load.
WIRING
Disconnect battery ground cable before making any power connections.
RED WIRE: +12 volts. Connect directly to battery positive terminal and should be
fused within 18 inches of battery and another fuse where the connection to the
amplifier is made. Remember to use the proper size fuses. WARNING: USING
OVERSIZED FUSES IS DANGEROUS AND WILL VOID THE WARRANTY!
See specifications for proper fuse size.
BLACK WIRE: negative ground. Connect to clean, unpainted metal surface on
car chassis.
RED/WHITE WIRE: Remote turn on lead requires 12 volts; connect to power
antenna lead from radio. When this not available, you may connect to a +12 volts
wire that is on with the ignition on or in the accessory position.
RCA CONNECTIONS: Connect with quality-shielded patch cords from source,
crossover, or any other sound processor.
SPEAKER CONNECTIONS: Slide wire into plug, with wires going down from
plug connections should be as follows: (From Left to Right): first slot Left (-),
second slot Left (+), Third slot Right (-) and fourth slot Right (+). For mono
operation use Left (+) and Right (-). These amplifiers are capable of 2-ohm
operation in stereo or 4 ohms in mono.
OPERATING THE AMPLIFIER AT LESS THAN THESE RATINGS WILL
CAUSE AMPLIFIER FAILURE AND VOID YOUR WARRANTY.
BRIDGED MONO OPERATION
The Model 992IQ is built with the right channel inverted. This allows the amplifier
to be used in a bridged mono configuration, as well as, a mixed mono/stereo
operation.
These amplifiers are capable of driving 2-ohm mono loads (**4 ohm speaker
impedance**). To use these amplifiers in that configuration, the internal taps
must be changed. Removing the faceplate and changing the spade connectors
from the ‘4’ setting to the ‘2’ setting accomplish this.
The wiring for the bridged mono mode is as follows:
With the connector end of the amplifier facing you, top side up, the speaker
terminal block is arranged: LEFT (-); LEFT (+); RIGHT (-); RIGHT (+). The mono
mode uses the LEFT (+) and RIGHT (-) connections. An electronic crossover,
such as the XO3, should be used to limit the frequency range to the input of the
amplifier for best results.
TWO-OHM CAPABILITY
Unplug the two jumper wires near the four large filter capacitors from the lugs
marked 4 ohm and press them firmly back onto lugs marked 2 ohm. This will
allow the amplifier to operate into a 2-ohm load on each channel, or a 4-ohm load
when used in bridged mono mode (**see statement above**). The lugs are
marked “2” for 2-ohm stereo or 4 ohm bridged, and marked “4” for 4-ohm stereo
and 8 ohm bridged.
GAIN ADJUSTMENT
Set the amp gain to minimum, turn the source up until it just starts to distort, then
back down slightly. This is the point where the output of the source is cleanest.
Now adjust the amplifier gain up until it just starts to distort and back down
slightly. This will allow the source and amp to reach maximum usable output at
the same time.
MOUNTING
1. The amplifier will work best if it is kept as cool as possible. Mount in a position
that allows air to flow freely through the fins. Be sure there is ample space above
the amplifier to avoid trapping heated air rising from the amplifier. The amplifier
should not be mounted upside down. Avoid mounting any amplifier in the dash or
on the firewall to avoid noises being radiated directly into the case.
2. The case of your amplifier is designed to act as a noise shield. To maintain
this protection, be sure the metal case of the amp does not touch the metal of the
car. Do not remove or damage the rubber grommets, which provide electrical
insulation and vibration isolation.
GENERAL TROUBLESHOOTING
NO SOUND
Check all connections. Check main power fuse. Check accessory fuse of your
vehicle. Check to see that +12Vdc is present at the amplifier on the power wire,
and on the red/white remote turn-on wire. Check for a solid ground connection.
Check that the main music source is putting out signal.
BLOWS FUSES
Check all connections to be sure no wires are touching each other or the chassis
of the vehicle or any other equipment in your install. Check that your speakers
are in proper working order.
SHUTS OFF
These amplifiers are equipped with a Thermal Shutdown System. If the amplifier
becomes too hot during operation, it will shutdown until it cools to proper
operating temperature. This can be caused by lack of proper air circulation to the
amp, or too low of speaker impedance.
Specifications
992IQ
992IQ
Power output @ 4 ohms RMS @ 12.5 volts 50X2
THD @ full output 20-20KHz .08%
Slew Rate volts/microsecond 8Vms
Damping factor @ 4 ohms >100
Channel separation 70dB
Maximum current
4 ohms 12A
2 ohms 16A
Idle .7A
Fuse rating (12 Volt Power Feed) 20A
Dimensions 2x7.7x7.5
Inhaltsverzeichnis
Andere Linear Power Verstärker Handbücher
Linear Power
Linear Power 652IQ Programmierhandbuch
Linear Power
Linear Power 502HV Programmierhandbuch
Linear Power
Linear Power LINEAR POWER 1001SW Programmierhandbuch
Linear Power
Linear Power 302IQ Programmierhandbuch
Linear Power
Linear Power LP50 Programmierhandbuch
Linear Power
Linear Power 401 Bedienungsanleitung
Linear Power
Linear Power Series TO-3 Programmierhandbuch
Linear Power
Linear Power LP100Z Programmierhandbuch
Linear Power
Linear Power MODEL 2120 Programmierhandbuch
Linear Power
Linear Power 952 Programmierhandbuch
Linear Power
Linear Power 3002 Programmierhandbuch
Linear Power
Linear Power 2202IQ Programmierhandbuch
Linear Power
Linear Power 452i Programmierhandbuch
Linear Power
Linear Power 1502IQ Programmierhandbuch
Linear Power
Linear Power DPSQ50 Programmierhandbuch
Linear Power
Linear Power 5002IQ Programmierhandbuch
Linear Power
Linear Power 4253IQ Programmierhandbuch
Linear Power
Linear Power 4503IQ Programmierhandbuch
Linear Power
Linear Power PA-1 Bedienungsanleitung
Linear Power
Linear Power PA-2 AudioPath Enhancer Bedienungsanleitung
