Linear Technology DC1418A-A Bedienungsanleitung

DEMO CIRCUIT 1418 QUICK START GUIDE LTC6604-X

DESCRIPTION

Demonstration circuit 1418 features the LT6604-XX se-

ries of a dual, matched, fully differential 4

order low-

pass filter

approximating a Chebyshev frequency re-

sponse

. The cutoff frequencies (Fc) of LT6604-XX are:

2.5MHz, 5MHz, 10MHz and 15MHz. (see Table 1).

The

LT6604-XX combines a lowpass filter with two fully

differential matched amplifiers for driving the differ-

ential inputs of a dual analog to Digital Converter

(ADC) and band-limiting the baseband signal of digi-

tal communications receiver.

Each LT6604-XX filter IC

requires only two external input resistors to set the fil-

ter’s differential gain.

A DC1418 board contains an

LT6604-XX configured with input resistors as two unity

gain differential amplifiers/lowpass filters.

ries of a dual, matched, fully differential 4

order low-

pass filter

approximating a Chebyshev frequency re-

sponse

. The cutoff frequencies (Fc) of LT6604-XX are:

2.5MHz, 5MHz, 10MHz and 15MHz. (see Table 1).

The

LT6604-XX combines a lowpass filter with two fully

differential matched amplifiers for driving the differ-

ential inputs of a dual analog to Digital Converter

(ADC) and band-limiting the baseband signal of digi-

tal communications receiver.

Each LT6604-XX filter IC

requires only two external input resistors to set the fil-

ter’s differential gain.

A DC1418 board contains an

LT6604-XX configured with input resistors as two unity

gain differential amplifiers/lowpass filters.

Gains greater than one require changing the input resis-

tors to a lower value (refer to an LTC6604-XX data sheet

and the DC1418 schematic).

Gains greater than one require changing the input resis-

tors to a lower value (refer to an LTC6604-XX data sheet

and the DC1418 schematic).

Connection to the differential input and output of a

DC1418 is through SMA connectors. On-board jumpers

configure the DC1418 for dual or single supply opera-

tion and internal or external output common (VOCM)

mode biasing. The differential input of a DC1418 is AC

coupled and can be configured for DC coupling by re-

placing shorting the input capacitors with zero ohms

surface-mount resistor jumpers. In addition, the

DC1418 has surface-mount pads to add input passive

components for input signal filtering and DC biasing.

Connection to the differential input and output of a

DC1418 is through SMA connectors. On-board jumpers

configure the DC1418 for dual or single supply opera-

tion and internal or external output common (VOCM)

mode biasing. The differential input of a DC1418 is AC

coupled and can be configured for DC coupling by re-

placing shorting the input capacitors with zero ohms

surface-mount resistor jumpers. In addition, the

DC1418 has surface-mount pads to add input passive

components for input signal filtering and DC biasing.

Design

files for this circuit board are available.Design

files for this circuit board are available.

Call the LTC factory.Call the LTC factory.

, LTC and LT are registered trademarks of Linear Technology Corporation.

DEMO CIRCUIT 1418

QUICK START GUIDE

LTC6604-2.5, LTC6604-5, LTC6604-10 and LTC6604-15

Dual, Matched, Fully-Differential, Lowpass Filter

ASSEMBLY

DC1418A-A LTC6604-2.5, Fc = 2.5MHz

DC1418A-B

LTC6604-5, Fc = 5MHz

DC1418A-C LTC6604-10, Fc = 10MHz

DC1418A-D LTC6604-15, Fc = 15MHz

Table 1. The DC1418 Assemblies

Figure 1. The DC1418 Top Silk Screen

DEMO CIRCUIT 1418 QUICK START GUIDE LTC6604-X

QUICK TEST SET UP

Quick Test Procedure

A DC1418 has two pairs of differential inputs,

Vin+A/Vin-A and Vin+B/Vin-B and two pairs of differen-

tial outputs Vout-A /Vout+A and Vout-B/Vout-B.

1. Testing the VinA to VoutA Signal Path.

Connect a DC1418 board as shown in Figure 2 (connect

signal generator to Vin+A and terminate Vin-A with a 50

ohm terminator). Set the generator for a 1MHz, 2Vp-p,

and sinewave. The oscilloscope channels connected to

Vout-A and Vout+A show a 1MHz, 1Vp-p, sinewave (see

Note 1).

Dual Power Supply

Oscilloscope (≥100MHz)

2. Testing the VinB to VoutB Signal Path.

Connect signal generator to Vin+B and terminate Vin-B

with a 50 ohm terminator. Set the generator for a 1MHz,

2Vp-p, and sinewave. Connect oscilloscope channel 1 to

Vout-B and channel 2 to Vout+B. The oscilloscope

channels connected to Vout-B and Vout+B show a

1MHz, 1Vp-p, sinewave.

Note 1:

For unity gain testing the DC1418 inputs must

be ideally driven by a zero ohm source (the outputs of a

high speed differential amplifier). However with the 50

ohm impedance of the generator’s output and termina-

tor is in series with the input resistors and the input to

output gain is less than one.

Note 2:

For single supply testing set the JP2 shunt to

SINGLE.

Signal Generator

with 50 Ohm Out

50 Ohm

Terminator

Figure 2. Dual Supply Test Set Up Connections

(set the JP1 shunt to VMIDA and the JP2 shunt to DUAL).

DEMO CIRCUIT 1418 QUICK START GUIDE LTC6604-X

DC1418A General Parts List

Tел:+7 (812) 336 43 04 (многоканальный)

Email: org@lifeelectronics.ru

www.lifeelectronics.ru

ООО “ЛайфЭлектроникс” “LifeElectronics” LLC

ИНН 7805602321 КПП 780501001 Р/С 40702810122510004610 ФАКБ "АБСОЛЮТ БАНК" (ЗАО) в г.Санкт-Петербурге К/С 30101810900000000703 БИК 044030703

Компания «Life Electronics» занимается поставками электронных компонентов импортного и

отечественного производства от производителей и со складов крупных дистрибьюторов Европы,

Америки и Азии.

С конца 2013 года компания активно расширяет линейку поставок компонентов по направлению

коаксиальный кабель, кварцевые генераторы и конденсаторы (керамические, пленочные,

электролитические),за счёт заключения дистрибьюторских договоров

Мы предлагаем:

Конкурентоспособные цены и скидки постоянным клиентам.

Специальные условия для постоянных клиентов.

Подбор аналогов.

Поставку компонентов в любых объемах, удовлетворяющих вашим потребностям.

Приемлемые сроки поставки, возможна ускоренная поставка.

Доставку товара в любую точку России и стран СНГ.

Комплексную поставку.

Работу по проектам и поставку образцов.

Формирование склада под заказчика.

Сертификаты соответствия на поставляемую продукцию (по желанию клиента).

Тестирование поставляемой продукции.

Поставку компонентов, требующих военную и космическую приемку.

Входной контроль качества.

Наличие сертификата ISO.

В составе нашей компании организован Конструкторский отдел, призванный помогать

разработчикам, и инженерам.

Конструкторский отдел помогает осуществить:

Регистрацию проекта у производителя компонентов.

Техническую поддержку проекта.

Защиту от снятия компонента с производства.

Оценку стоимости проекта по компонентам.

Изготовление тестовой платы монтаж и пусконаладочные работы.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Linear Technology Hauptplatine Handbücher

Linear Technology

Linear Technology DC2026 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC981A Bedienungsanleitung

Linear Technology

Linear Technology DC391A Bedienungsanleitung

Linear Technology

Linear Technology DC2181A-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1762A-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1877A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC776 Bedienungsanleitung

Linear Technology

Linear Technology DC2269A-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC416 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1317A-B Bedienungsanleitung

Linear Technology

Linear Technology DC1198B-B Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC937A Bedienungsanleitung

Linear Technology

Linear Technology DC1755A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1905A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1041A-B Bedienungsanleitung

Linear Technology

Linear Technology LTC2374 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1780A-A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1732 Series Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC980A Bedienungsanleitung

Linear Technology

Linear Technology DC2215A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2125 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2172A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1472A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC503A Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung