Linear Technology DC1928A Kurzanleitung zur Einrichtung

dc1928af

DEMO MANUAL DC1928A

DESCRIPTION

LTC3867EUF

High Efficiency Synchronous

Buck Converter

Demonstrationcircuit1928Ais asingleoutputsynchronous

buck converter featuring the LT C

3867EUF in a 24-lead

4mm x 4mm QFN package.

The DC1928A is configured with a sense resistor. Inductor

DCR sensing circuit is optional. Using the inductor’s DCR

as the sense element instead of the onboard sense resistor

saves cost, board space while improving efficiency. Using

a sense resistor provides more accurate current limit.

The board has a lot of features including an internal 5V

linear regulator for bias, output voltage remote-sense,

programmable nonlinear control to improve load tran-

sient performance, programmable thermal shutdown, an

L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks

of Linear Technology Corporation. All other trademarks are the property of their respective

owners.

PERFORMANCE SUMMARY

optional temperature compensated DCR sense circuit,

and selectable continuous, pulse-skipping or Burst Mode

operation. Synchronization to an external clock is also

possible.

The input voltage range is from 18V to 36V. The LTC3867

data sheet gives a complete description of the part, opera-

tion and application information and must be read in con-

junction with this demo manual for DC1928A.

Design files for this circuit board are available at

http://www.linear.com/demo

Specifications are at TA= 25°C

PARAMETER CONDITIONS / NOTES VALUE

Input Voltage Range 18V ~ 36V

Output Voltage, VOUT VIN = 18V ~ 36V, IOUT = 0A ~ 12A, JP3: CCM 12V ±2% (11.76V ~ 12.24V)

Default Operating Frequency (Typical) 250kHz

External Clock Sync. Frequency Range 200kHz to 780kHz

Typical Full Load Efficiency (See Figure 3) VIN = 24V, VOUT = 12V, IOUT1 = 12A, fSW = 250kHz 97.6%

Downloaded from Arrow.com.

dc1928af

DEMO MANUAL DC1928A

QUICK START PROCEDURE

Demonstration circuit DC1928A is easy to set up to evalu-

ate the performance of the LTC3867EUF. Please refer to

Figure 2 for proper measurement equipment setup and

follow the procedure below:

1. Place jumpers in the following positions for a typical

application:

JP2: On

JP3: CCM

2. With power off, connect the input power supply, load

and meters as shown in Figure 1. Preset the load to 0A

and VIN supply to 24V.

3. Turn on the power supply at the input.

Note:Makesure that theinput voltage doesnot exceed 36V.

4. Check the output voltage. The output voltage should

be between 11.76V and 12.24V.

Oncethe proper output voltage isestablished, adjust the

load within the operating range and observe the output

voltage regulation, output voltage ripple, efficiency and

other parameters.

Note: When measuring the input or output voltage ripple,

care must be taken to avoid a long ground lead on the

oscilloscope probe. Measure the input or output voltage

ripple by touching the probe tip directly across the VIN or

VOUT and GND terminals. See Figure 2 for proper scope

probe technique.

5. ChangeJP3 jumper position to selectdifferent operation

modes. Set jumper to CCM, BURST or P.S. position

toe set forced continuous conduction, burst or pulse-

skipping mode respectively. For synchronizing to an

external clock source, set the jumper to BURST position

and apply the clock signal to MODE/PLLIN turret.

Figure 1. Test Setup of DC1928A

Downloaded from Arrow.com.Downloaded from Arrow.com.

dc1928af

DEMO MANUAL DC1928A

QUICK START PROCEDURE

RAIL TRACKING

Figure 2. Measuring Input or Output Ripple Across Terminals or Directly Across Bulk Capacitor

ILOAD (A)

EFFICIENCY (%)

60 5 9

37 11

26 10

48 12

100

PULSE-SKIPPING

FCM

BURST

Figure 3. Measured Efficiency

Demonstration circuit 1928A is configured for an onboard

soft-start circuit. The soft-start ramp rate can be adjusted

by changingthe value of C24. Demonstration circuit1928A

can also be modified to track an external reference. Refer

to Table 1 for tracking options and to the data sheet for

more details.

CONFIGURATION

TRK/SS RESISTORS AND CAPACITOR RAIL TRACKING

R32 R35 C24 TRK/SS PIN

Soft-Start without Tracking (Default) 0Ω Open 0.1µF OPEN

VOUT Equals External Ramp 0Ω Open Open External Reference Applied

VOUT Tracking Scaled External Ramp Resistor Divider Open External Reference Applied

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

dc1928af

DEMO MANUAL DC1928A

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 1 CIN1 CAP, ALUM, 56µF 20% 50V SUN ELECT 50HVH56M

2 2 CIN3, CIN6 CAP, X5R 10µF 20% 50V 1210 TAIYO YUDEN UMK325BJ106MM-T

5 2 COUT1, COUT2 CAP, POSCAP 150µF 20% 16V 7343 SANYO, 16TQC150MYF

7 2 COUT4, COUT8 CAP, X5R 22µF 20% 16V 1210 AVX 1210YD226MAT2A

9 1 C32 CAP., X7R 10pF 10% 25V 0603 AVX 06033C100KAT2A

10 1 C33 CAP, X5R 1µF 10% 50V 0603 TDK C1608X5R1E105K

11 1 C19 CAP, X5R 0.033µF 10% 50V 0603 AVX 06035D333KAT2A

12 1 C30 CAP, X7R 1nF 10% 25V 0603 AVX 06033C102KAT

13 2 C24, C25 CAP, X5R 0.1µF 10% 10V 0603 AVX 0603ZD104KAT

14 1 C26 CAP, C0G 470pF 5% 50V 0603 MURATA GCM1885C1H471JA16D

15 1 C27 CAP, X5R 4.7µF 10% 10V 0603 AVX 0603ZD475KAT2A

16 1 C28 CAP, C0G 100pF 5% 50V 0603 TDK C1608COG1H101JK

17 1 D1 DIODE, 6.8V SOD-323 CENTRAL CMDZ6L8

18 1 D2 DIODE, SOD-323 CENTRAL SEMI CMDSH05-4-LT C

23 1 L1 IND., 7µH WURTH., 7443630700

24 2 Q1, Q3 XSTR, MOSFET LFPAK INFINEON BSC035N04LSG

28 1 RSNSE RES, 3mΩ 1% 1W 2512 PANASONIC ERJM1WTF3M0U

29 2 R9, R10 RES, 100Ω 1% 1/10W 0603 NIC NRC06F1000TRF

31 4 R32, R36, R56, R58 RES, 0Ω 1/10W 0603 VISHAY CRCW06030000Z0EA

32 1 R33 RES, 100k 1% 1/10W 0603 NIC NRC06F1003TRF

33 1 R37 RES, 2.2Ω 5% 1/10W 0603 NIC NRC06F2R20TRF

34 1 R39 RES, 191KΩ 1% 0603 VISHAY CRCW060375K0FKEA

35 4 R38, R53, R57, R59 RES, 10k 1% 0603 NIC NRC06F1002TRF

36 1 R40 RES, 44.2k 1% 0603 VISHAY CRCW060344K2FKEA

37 1 R51 RES, 30.1k 1% 0603 NIC NRC06f3012TRF

38 3 R49, R50, PTC RES, 10Ω 1% 0603 NIC NRC06f10R0TRF

39 1 U1 IC., LTC3867EUF, QFN 4mm x 4mm LINEAR TECH. LTC3867EUH#PBF

Additional Demo Board Circuit Components

1 2 COUT5, COUT7 (OPT)

2 3 CIN4, CIN5, CIN7, CAP, X5R 22µF 20% 25V 1210

3 1 COUT3 (OPT) CAP, POSCAP 7343

4 3 C18, C23, C29 (OPT) CAP, 0603

5 2 Q2, Q4 (OPT) XSTR, MOSFET LFPAK

6 1 Q5 (OPT) XSTR, MOSFET, DUAL N-CHANNEL

7 13 R1, R27, R29, R35, R42, R43,

R46-R48, R52, R54, R55, RNTC (OPT)

RES, 0603

Hardware-For Demo Board Only

1 8 E1, E2, E4-E11 TURRET, 0.094" MILL-MAX 2501-2-00-80-00-00-07-0

2 1 JP2 HEADER, 3-PIN SAMTEC TMM-103-02-L-S

3 1 JP3 HEADER, 4-PIN SAMTEC TMM-104-02-L-S

4 4 J1-J4 JACK, BANANA KEYSTONE 575-4

5 2 XJP2, XJP3 SHUNT SAMTEC 2SN-BK-G

6 4 STANDOFF, SNAP ON KEYSTONE 8832

7 1 FAB, PRINTED CIRCUIT BOARD DEMO CIRCUIT 1928A

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

dc1928af

DEMO MANUAL DC1928A

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-

tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.

SCHEMATIC DIAGRAM

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

dc1928af

DEMO MANUAL DC1928A

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

(408) 432-1900 ●FAX: (408) 434-0507 ●www.linear.com

 LINEAR TECHNOLOGY CORPORATION 2013

LT 0513 • PRINTED IN USA

DEMONSTRATION BOARD IMPORTANT NOTICE

Linear Technology Corporation (LT C ) provides the enclosed product(s) under the following AS IS conditions:

This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT

OR EVALUATION PURPOSES ONLY and is not provided by LT C for commercial use. As such, the DEMO BOARD herein may not be complete

in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety

measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union

directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.

If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date

of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LT C from all claims

arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all

appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or

agency certified (FCC, UL, CE, etc.).

No License is granted under any patent right or other intellectual property whatsoever. LT C assumes no liability for applications assistance,

customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.

LT C currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.

Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and

observe good laboratory practice standards. Common sense is encouraged.

This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LT C applica-

tion engineer.

Mailing Address:

Linear Technology

1630 McCarthy Blvd.

Milpitas, CA 95035

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Inhaltsverzeichnis

Andere Linear Technology Hauptplatine Handbücher

Linear Technology

Linear Technology LTC6905 Series Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1818A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1496C Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LTC5584 Bedienungsanleitung

Linear Technology

Linear Technology DC2218A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1513B Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1698A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1529A Bedienungsanleitung

Linear Technology

Linear Technology DC1771A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2073A Series Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1842A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC426B Bedienerhandbuch

Linear Technology

Linear Technology DC391A Bedienungsanleitung

Linear Technology

Linear Technology DC2125 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LT3015 Bedienungsanleitung

Linear Technology

Linear Technology DC1317A-B Bedienungsanleitung

Linear Technology

Linear Technology DC1605B Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2172A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1145B Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1765A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology LTC2107 Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC1763A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2025A Kurzanleitung zur Einrichtung

Linear Technology

Linear Technology DC2072A Kurzanleitung zur Einrichtung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung