Linear Technology DC273A Kurzanleitung zur Einrichtung
1
dc273af
DEMO MANUAL DC273A
Description
LTC2408
4-/8-Channel 24-Bit µPower
No Latency ΔΣ ADC
The LT C
®
2408, an 8-channel 24-bit no latency ∆∑ ADC is
featuredontheDC273Ademonstrationboard.TheLTC2408
features a 4ppm linearity, 4ppm full-scale accuracy, 1ppm
offset accuracy, and 0.3ppm RMS noise.
The LTC2408 performs interleaved auto-zero and cali-
bration cycles which are transparent to the user.
The device does not require initialization or configuration,
other than selecting the multiplexer channel.
The board includes a precision 2.5V reference (LT1019-
2.5),as well as bypassingcapacitors,and jumpers to select
line frequency rejection and on board /external reference.
The demonstration board is designed to be incorporated
into a target system, as well as give an example of good
placement of bypass and partitioning of an analog and
digital ground.
Design files for this circuit board are available at
http://www.linear.com/demo
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Figure 1. DC273A Set-Up
2
dc273af
DEMO MANUAL DC273A
Quick start proceDure
All of the digital control lines are on a 0.070" header (J17).
On the DC273A demonstration board CSMUX and CSADC
are tied together, as are SLK and CLK. This allows the ADC
tobe addressed througha minimum of control lines. When
the CSMUX and CSADC are logic High, address data can
be clocked into the MUX. When CSMUX and CSADC are
logic low, conversion data can be clocked out of the ADC.
Refer to the LTC2408 data sheet for a complete description
of the various serial interface modes.
The DC273A incorporates 2 jumpers: JP1, which allows
the on-board or an external reference, to be selected; and
JP2, which allows selection of 50Hz/60Hz line frequency
rejection.
All the analog inputs are provided with turrets along one
edge of the board, positioned to be compatible with clip
leads. Tw o ground connections (J9 and J10) are provided
for interconnection into an analog subsystem or to be used
as separate returns for two signal groups.
Power and ground are provided on J15 and J16, and ref-
erence in and out are provided on J13 and J14.
Interconnection of analog and digital subsystems can be
made through these ground connections, or all should
return to a star ground at a point in the target system.
All ground connections should be as short as possible.
The multiplexer output is linked to the ADC through a 5k
resistor. Both terminals are available, J11 for MUXOUT,
and J12 for ADCIN. As the multiplexer output can be dis-
abled, multiplexer expansion can be brought to either of
these terminals. Optionally, an amplifier (buffer) can be
used to drive ADCIN, without necessarily removing the 5k
resistor. If an amplifier with voltage gain is introduced, it
is recommended that the resistor be removed. Depending
on the source resistance or drive capabilities of nodes driv-
ing the multiplexer inputs, J11 can be tied directly to J12.
Please see the LTC2400 data sheet for more information
on driving the input of the LTC2408.
SeethetimingdiagramforMUX,andDataOutputoperation.
F0 is available on J17 for external conversion clock. See
full data sheet for use of this line, otherwise, leave open.
Use of external clock requires removal of JP2.
The LTC2408’s F0 pin is available on J17 for those applica-
tions where an external oscillator controls the conversion
time of the ADC. JP2 must be removed in this case. Please
consult the LTC2408 data sheet for more information on
the use of F0. If an external oscillator is not required, leave
pin 1 on J17 open.
parts List
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
1 2 C1, C2 CAP., TAN 10µF 16V AVX, TAJB106M016, 3528
2 2 C3, C4 CAP., X7R 1µF 10V AVX, 0805ZC105KAT1A, 0805
3 1 R2 RES., CHIP 3.3 5% TAD CR16-3R3JM, 0603
4 2 R3, R4 RES., CHIP 100 5% TAD CR16-101JM, 0603
5 1 R1 RES., CHIP 5.1k 5% TAD CR16-512JM, 0603
6 16 J1-J16 TERMINAL, TURRET .065" MIL-MAX 2308-02
7 2 JP1-JP2 HEADER, 3×1 .079" CENTER COMM CON 2802S-3G2
8 1 JP3 HEADER, 5×2 .079" CENTER COMM CON 2202S-10G2
9 3 JP1-JP3 SHUNT, CCIJ2MM-138-G COMM CON. CCIJ2MM-138-G
10 1 U2 IC., LT1019ACS8-2.5V LINEAR LT1019ACS8-2.5V, SO8
11 1 U1 IC., LTC2408CG LINEAR LTC2408CG
3
dc273af
DEMO MANUAL DC273A
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
schematic Diagram
4
dc273af
DEMO MANUAL DC273A
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ●FAX: (408) 434-0507 ●www.linear.com
LINEAR TECHNOLOGY CORPORATION 2013
LT 0513 • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LT C ) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LT C for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LT C from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LT C assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LT C currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LT C applica-
tion engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Linear Technology Hauptplatine Handbücher
Linear Technology
Linear Technology DC1705C Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology DC2376A Bedienungsanleitung
Linear Technology
Linear Technology DC1670A Bedienungsanleitung
Linear Technology
Linear Technology DC1721B-B Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology DC2566A Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology 1029 Bedienungsanleitung
Linear Technology
Linear Technology DC1959B Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology LTC5585 Bedienungsanleitung
Linear Technology
Linear Technology DC1836A Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology DC1624A Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology DC1555B Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology DC814 Bedienungsanleitung
Linear Technology
Linear Technology DC1317A-B Bedienungsanleitung
Linear Technology
Linear Technology DC1842B Bedienungsanleitung
Linear Technology
Linear Technology DC2177A-B Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology DC1696 Kurzanleitung zur Einrichtung
Linear Technology
Linear Technology DC391A Bedienungsanleitung
Linear Technology
Linear Technology LTC3526 Bedienungsanleitung
Linear Technology
Linear Technology 968A-B Bedienungsanleitung
Linear Technology
Linear Technology DC2522A Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
