Linear GSLG-A Bedienungsanleitung

GSLG-A

Slide Gate Operator

Installation Guide

Operator models contained in this manual

conform to UL325 standard for use in

Class I, II, III, and IV applications

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.linearcorp.com

GSLG-A Slide Gate Operator Installation Guide - ii - P1222 Revision X5 6-22-2011

Table of Contents

Pre-installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Begin... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Always Check the Gate’s Action . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Gate Operator Classiﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Approved Obstruction Detection Devices . . . . . . . . . . . . . . . . . . . . . 1

Safety Information and Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Regulatory Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Wiring Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

AC Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

DC Control and Accessory Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . .2

Mounting Pad Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Gate Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Mounting Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Gate Bracket and Chain Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Operator Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Vent Plug Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operator Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Controller Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Manual Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

AC Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Earth Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Open and Close Limit Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . .6

Limit Nuts Rough Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Limit Nuts Fine Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Torque Limiter Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Controller Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Indicator Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Terminal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Operator Accessory Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Basic Controller Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Programming Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Entering Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Exiting Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Programming Keystrokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Left or Right Hand Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Dual Gate Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Auto Close Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Run Alarm and Pre-start Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Maximum Open Direction Current Setting. . . . . . . . . . . . . . . . . . . .12

Maximum Close Direction Current Setting . . . . . . . . . . . . . . . . . . .12

Advanced Controller Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Entering Advanced Programming Mode . . . . . . . . . . . . . . . . . . . . .13

Maximum Run Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Single Button Input Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Stagger Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Stagger Delay Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Auxiliary Relay Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Reverse Delay Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Brake Delay Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Constant Pressure Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Shadow Loop Open Prevention. . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Reset Cycle Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Maintenance Alert Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Mid-travel Stop Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Anti-tailgate Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Radio Enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Antenna Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Radio Transmitter Learn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Radio Transmitter Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

MGT Obstacle Transmitter Learn . . . . . . . . . . . . . . . . . . . . . . . . . .16

MGT Obstacle Transmitter Delete . . . . . . . . . . . . . . . . . . . . . . . . . .16

Motor Type Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Loop Layout Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Safety Edge Layout Illustration #1. . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Safety Edge Layout Illustration #2. . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Photoeye Installation Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Picket Gate Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Track Gate Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Dual Gate Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Optional In-Cabinet Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Gate Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Open Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Close Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Single Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Fire Department Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Open Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Open Obstruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Close Obstruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Reverse Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Open Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Reverse Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Shadow/reset Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Operation Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Power-up Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Idle Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Last Gate Position/Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Pre-start Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Reverse Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Run Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Error Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Entrapment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

COMM LINK Connection Failure . . . . . . . . . . . . . . . . . . . . . . . . . . .25

MGT Obstacle Transmitter Trouble . . . . . . . . . . . . . . . . . . . . . . . . .25

Maximum Run Time Exceeded . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

How to Order Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . .26

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Contacting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Operator fails to start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Motor operates, but gate does not move. . . . . . . . . . . . . . . . . . . . .26

Motor sounds like it is working harder than normal . . . . . . . . . . . . .26

Limit switch getting out of time . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Gate stopping part way open or closed

(but no visible obstruction). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Gate staying open with automatic system. . . . . . . . . . . . . . . . . . . .26

Preventative Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

6-Month Preventative Maintenance. . . . . . . . . . . . . . . . . . . . . . . . .27

FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Model GSLG-A Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Single Phase Controller Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Three Phase Controller Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Gate Operator Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . .32

ONLY QUALIFIED TECHNICIANS

SHOULD WORK ON

LINEAR SLIDE GATE

OPERATORS

WARNING

CONTROLS INTENDED FOR USER ACTIVATION MUST BE

LOCATED AT LEAST SIX FEET (6') AWAY FROM ANY MOVING

PART OF THE GATE AND WHERE THE USER IS PREVENTED

FROM REACHING OVER, UNDER, AROUND OR THROUGH THE

GATE TO OPERATE THE CONTROLS. OUTDOOR OR EASILY

ACCESSIBLE CONTROLS SHALL HAVE A SECURITY FEATURE

TO PREVENT UNAUTHORIZED USE.

GSLG-A Slide Gate Operator Installation Guide - 1 - P1222 Revision X5 6-22-2011

Pre-installation Information

Before You Begin...

Before unpacking, inspect the carton for exterior damage. If

you ﬁnd damage, advise the delivery carrier of a potential

claim. Inspect your package carefully. You can check your

accessory box parts with the enclosed packing slip for your

convenience. Claims for shortages will be honored for only

30 days from the date of shipment.

Before installing the operator, read this manual completely to

ensure all requirements for proper installation are present. Verify

that the voltage to be used matches the voltage of the operator.

If you have any questions about the requirements for proper

installation of this gate operator contact technical support at

800-421-1587

Always Check the Gate’s Action

It’s very important before installing the gate operator to

make sure the gate’s slides free and level throughout

the entire opening distance. If the gate does not seem to

operate properly, it may affect the operator performance

or greatly shorten the life of the unit. The gate should

also be designed so that airﬂow is ample to prevent

wind resistance and drag.

Gate Operator Classiﬁcations

All gate operators can be divided into one of four different

classiﬁcations, depending on their design and usage. Install

this gate operator only when the operator is appropriate for

the construction and usage class as deﬁned below:

• Class I Residential Vehicular Gate Operator

A vehicular gate operator intended for use in a home or for one to

four single family dwellings with a common garage or parking area

associated with these dwellings.

• Class II Commercial / General Access Vehicular Gate Operator

A vehicular gate operator intended for use in a commercial location or

building such as a multi-family housing unit of ﬁve or more single family

units, hotel, retail store or other building servicing the general public.

• Class III Industrial / Limited Access Vehicular Gate Operator

A vehicular gate operator intended for use in an industrial location or

building such as a factory or loading dock area or other location not

intended to service the general public.

• Class IV Restricted Access Vehicular Gate Operator

A vehicular gate operator intended for use in a guarded industrial

location or building such as an airport security area or other restricted

access locations not servicing the general public, in which unauthorized

access is prevented via supervision by security personnel.

Approved Obstruction Detection Devices

The following contact or non-contact obstruction detection

devices have been approved for use with this slide gate

operator as part of a UL325 compliant installation:

• Contact Edges

Miller Edge Models MGO20, MGR20, MGS20, ME120

• Photoeyes

MMTC Model IR-55 (165’ range - P/N 2520-441)

MMTC Model E3K (28’ range - P/N 2520-031)

Safety Information and Warnings

Regulatory Warnings

Read the following before beginning to install this slide gate

operator:

WARNING

This type of warning note is used to

indicate possible mechanical hazards that

may cause serious injuries or death.

CAUTION

This type of warning note is used to

indicate the possibility of damage to the

gate or gate operator.

WARNING

This type of warning note is used to indicate

possible electrical shock hazards that may

cause serious injuries or death.

THE FOLLOWING FORMATS ARE USED FOR SAFETY NOTES

IN THESE INSTRUCTIONS.

IMPORTANT INSTALLATION SAFETY INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH

TO PERSONS, REVIEW THESE INSTALLATION SAFETY

STEPS BEFORE PROCEEDING

1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2. Read the yellow “Safety Instructions” brochure enclosed with the

packet of information. If any pages are missing or are unreadable,

or you do not have the safety instructions, please call Linear at

1-800-333-1717 to request additional copies.

3. ALL ELECTRICAL CONNECTIONS TO THE POWER SUPPLY MUST

BE MADE BY A LICENSED ELECTRICIAN AND MUST OBSERVE ALL

NATIONAL AND LOCAL ELECTRICAL CODES.

4. A separate power-disconnect switch should be located near the

operator so that primary power can be turned off when necessary.

5. Install the enclosed warning signs on both sides of the gate. A

minimum of two (2) WARNING SIGNS shall be installed, one on each

side of the gate where easily visible.

6. Never reach between, through or around the fence to operate the

gate.

7. Never connect a button station within reach of the gate or on the

side of the gate operator.

8. Do not adjust the operator controller’s current sensing feature too

high. It should be adjusted high enough to keep the gate from falsely

triggering the sensing, but no higher than necessary for the gate to

operate. DO NOT DEFEAT THE PURPOSE OF THIS FUNCTION!

9. You must install all required safety equipment.

10. UL325 Compliance requires the use of contact edges or photoelectric

controls on all automatic or remotely-controlled gate operators.

11. The operator is intended for installation only on gates used for

vehicles. Pedestrians must be supplied with a separate access

opening. The pedestrian access opening shall be designed to

promote pedestrian usage. Locate the gate such that persons will

not come into contact with the vehicular gate during the entire path

of travel of the vehicular gate.

GSLG-A Slide Gate Operator Installation Guide - 2 - P1222 Revision X5 6-22-2011

Wiring Speciﬁcations

Refer to the following steps for details on power and

accessory wiring for the operator.

AC Power Wiring

1. Find the listing on this page corresponding to the model, voltage and

horsepower rating of your operator.

2. The distance shown in the table is measured in feet from the

operator to the power source. DO NOT EXCEED THE MAXIMUM

DISTANCE. These calculations have been based on standard 115 V

and 230 V supplies with a 10% drop allowable. If your supply is under

the standard rating, the runs listed may be longer than what your

application will handle, and you should not run wire too near the

maximum distance for the gauge of wire you are using.

3. When large-gauge wire is used, a separate junction box (not

supplied) may be needed for the operator power connection.

4. Wire length calculations are based on the National Electrical Code,

Article 430 and have been carefully determined based on motor

inrush, brake solenoids, and operator requirements.

5. Connect power in accordance with local codes. The green ground

wire must be properly connected.

6. Wire insulation must be suitable to the application.

7. Electrical outlets are supplied in all 115 VAC models for convenience

with occasional use or low power consumption devices only. If

you choose to run dedicated equipment from these devices, it will

decrease the distance for maximum length and the charts will no

longer be accurate.

DC Control and Accessory Wiring

1. All control devices are now 24 VDC, which can be run up to 2000

feet with 14 AWG wire.

2. Control wiring must be run in a separate conduit from power wiring.

Running them together may cause interference and faulty signals in

some accessories.

3. A three-wire shielded conductor cable is required to connect two

operators together for dual operation. You must use Belden 8760

Twisted Pair Shielded Cable (or equivalent) only – P/N 2500-1982,

per foot). See Page 25 for details of this connection. Note: The shield

wire should be connected in both the operators.

WARNING

ALL AC ELECTRICAL CONNECTIONS TO THE POWER SOURCE AND

THE OPERATOR MUST BE MADE BY A LICENSED ELECTRICIAN

AND MUST OBSERVE ALL NATIONAL AND LOCAL ELECTRICAL

CODES.

USE COPPER WIRE ONLY!

MODEL GSLG-A SINGLE PHASE POWER WIRING

VOLTS & HP MAXIMUM DISTANCE (FEET) WIRE GAUGE

SINGLE DUAL

115 VOLTS

1/2-HP

222 111 12

354 177 10

566 283 8

900 450 6

1430 715 4

115 VOLTS

3/4-HP

178 89 12

282 141 10

450 255 8

716 358 6

1140 570 4

115 VOLTS

1-HP

160 80 12

254 127 10

406 203 8

646 323 6

1026 513 4

208 VOLTS

1/2-HP

760 380 12

1200 600 10

1924 962 8

3060 1830 6

4864 2432 4

208 VOLTS

3/4-HP

604 302 12

958 478 10

1526 763 8

2424 1212 6

3856 1928 4

208 VOLTS

1-HP

544 272 12

864 432 10

1374 686 8

2184 1092 6

3476 1738 4

230 VOLTS

1/2-HP

894 447 12

1422 711 10

2264 1132 8

3600 1800 6

5724 2862 4

230 VOLTS

3/4-HP

710 355 12

1128 564 10

1796 898 8

2852 1426 6

4538 2269 4

230 VOLTS

1-HP

640 320 12

1016 508 10

1616 808 8

2570 1285 6

4090 2045 4

MODEL GSLG-A THREE PHASE POWER WIRING

VOLTS & HP MAXIMUM DISTANCE (FEET) WIRE GAUGE

SINGLE DUAL

208 VOLTS

1/2-HP

1142 571 12

1816 908 10

2890 1445 8

208 VOLTS

3/4-HP

920 460 12

1464 732 10

2330 1165 8

208 VOLTS

1-HP

714 357 12

1136 568 10

1804 902 8

230 VOLTS

1/2-HP

1344 672 12

2137 1069 10

3400 1700 8

230 VOLTS

3/4-HP

1084 542 12

1723 862 10

2741 1371 8

230 VOLTS

1-HP

840 420 12

1336 668 10

2124 1062 8

460 VOLTS

1/2-HP

3841 1921 12

6106 3053 10

9712 4856 8

460 VOLTS

3/4-HP

3279 1640 12

5212 2606 10

8291 4146 8

460 VOLTS

1-HP

2689 1345 12

4274 2437 10

6798 3399 8

GSLG-A Slide Gate Operator Installation Guide - 3 - P1222 Revision X5 6-22-2011

Mounting Pad Installation

The gate operator mounts bolted to posts secured in

concrete footings. The posts support the operator and

prevent it from moving during operation. For optional pad

mounting instructions, see Linear drawing #2700-360.

Gate Preparation

Before installing, make sure the gate rolls or slides freely,

and that all exposed rollers are properly covered. The gate

must be covered with fabric with openings no larger than

2-1/4” in size, to a minimum height of 72” above ground

level. On picket-style gates, if pickets are spaced less than

2-1/4” apart, mesh is optional.

Mounting Speciﬁcations

Use two 3 - 3-1/2” OD galvanized posts and secure with

concrete footings as shown, length to be determined by

local codes, frost line depth and soil conditions.

Attach the operator with the U-bolts, side plates and

hardware provided. Four 3/16” side plates go on the outside

top and bottom, two 1/2” side plates go on the inside top,

and two 3/16” side plates go on the inside bottom (see the

illustration at right).

To assemble the drive chain and gate brackets, refer to

Page 4. Make sure that the chain sag does not exceed

recommended sizes and that the chain does not come into

contact with the moving parts of the gate or ground.

Figure 2. Post Mounting Speciﬁcations

WARNING

The operator is intended for installation only on gates used for

vehicles. Pedestrians must be supplied with a separate access

opening. The pedestrian access opening shall be designed to

promote pedestrian usage. Locate the gate such that persons

will not come into contact with the vehicular gate during the

entire path of travel of the vehicular gate.

WARNING

The gate must be installed in a location so that enough

clearance is supplied between the gate and adjacent

structures when opening and closing to reduce the risk of

entrapment.

Figure 1. Side

Plate Installation

72”

GSLG-A Slide Gate Operator Installation Guide - 4 - P1222 Revision X5 6-22-2011

Gate Bracket and Chain Assembly

✓NOTE: The item numbers shown in these illustrations

are for reference only. For the actual part numbers, refer

to the parts lists in the rear of this manual.

Assemble a gate bracket (1) to the front edge of the gate,

using two U-bolts (2), and mounting hardware (3). Before

tightening down completely, be sure the bracket is parallel

to the gate. Tighten the U-bolt hardware the rest of the way,

then screw the square head bolts (4) into the threaded

holes in the gate plate until they bottom out against the gate.

These will help keep the bracket from twisting on the pipe.

Slide a threaded chain pin (5) through the bracket as shown,

with spring (6), ﬂat washer (10), and two hex nuts (7). Attach

one end of the drive chain (8) to the chain pin using master

link (9) and begin unrolling the chain toward the operator.

Remove the rain cover from the back of the slide gate

operator. Carefully thread the drive chain under the ﬁrst

idler, over the drive sprocket, and then under the last idler.

Make sure you feed most of the chain through the idlers and

sprocket before attaching the chain to the back end of the

gate.

Assemble the other gate bracket on the rear edge of the

gate, using the same process as the front gate bracket.

Once this is done, take the other chain pin, spring and jam

nuts and assemble with the end of drive chain and the other

master link.

At this point you should be able to adjust the chain tension

by tightening the jam nuts on each end. Approximately

1/4” to 3/8” of slack per foot of drive chain is acceptable.

Make sure the chain does not drag on the ground, across

the gate rollers or the idler frame of the operator.

Additional mounting holes have been provided in the gate

bracket for installer convenience.

Operator Preparation

Vent Plug Installation

In order to keep gear oil from spilling out during shipping,

gear reducers used in this gate operator has either a solid

plug, or a sealed vent plug, installed at the factory.

For operators with a solid plug, replace the solid plug with

the vent plug provided (see Figure 5).

With the vent plug installed, remove the vent plug’s breather

pin to allow the gear box to vent (see Figure 5).

END OF GATE PIPE SHOWN

REFERENCE ONLY

Figure 2. Mounting Gate Bracket to Gate

Figure 3. Chain Pin and Chain Assembly

710

NOTE: IDLER CONFIGURATION

MAY APPEAR DIFFERENT DEPENDING

ON THE SLIDE OPERATOR MODEL

DRIVE

SPROCKET

DRIVE SPROCKET

IDLER

WHEEL

IDLERWHEEL

CHAIN

PATH

CHAIN

PATH

IDLERWHEEL

Figure 4. Chain PathFigure 5. Vent Plug Installation

REMOVE THE

SOLID PLUG

WITH AN ALLEN

WRENCH

GEAR

REDUCER

INSTALL THE

VENT PLUG

(IF NOT ALREADY

INSTALLED)

REMOVE THE

BREATHERPIN

INSTALL THE VENT PLUG

(IF NOT ALREADY INSTALLED)

GSLG-A Slide Gate Operator Installation Guide - 5 - P1222 Revision X5 6-22-2011

Operator Setup

Controller Access

The Controller is protected by a plastic dust cover (single

phase models only). To remove the dust cover, loosen the

cover’s wing-screw and lift the cover off (see Figure 5).

Manual Disconnect

The manual disconnect shifter lever and the locking lever is

illustrated in Figure 8. They can be found at the center and

to the left inside the operator cabinet. (The handle of each

has been ﬁnished in easy to spot red ﬁrm-grip coating.)

To disconnect the unit for manual operation, grasp the

handle of the spring-loaded shifter lever and pull it directly

toward you until the spring-loaded locking lever snaps into

place behind it. This action disengages the pinned shifter

block from the drive mechanism and holds the block in the

disengaged position.

To re-engage the operator, move the locking lever to the

right, releasing the spring-loaded shifter lever to snap back

into the engaged position.

AC Power Connection

All Linear gate operators are supplied with a power

disconnect switch to turn on and off the power available to

the operator (see Figure 6). Following wiring speciﬁcations

on Page 2, incoming power should be brought into the

operator and connected to the labeled pigtails from the

disconnect box. A wiring connections print can also be

found on the label inside the cover of the operator.

Proper thermal protection is supplied with the operator. The

motor contains a thermal overload protector to guard from

overheating the motor due to overload or high-frequency

operation. This overload protector will reset automatically

after the motor cools down.

Earth Ground

Install a ground rod and connect it to the operator’s frame

in every gate operator installation. A good earth ground

is necessary to allow the Controller’s built-in surge and

lightning protection circuitry to work effectively. The physical

bolting of the operator to the mounting pad is not sufﬁcient

for a good earth ground.

✓NOTE: Do not splice the ground wire. Use a single piece of solid

copper 12 AWG wire between the ground rod and the operator.

1. Install an 8-foot long copper ground rod next to the operator mounting

pad within three feet of the operator.

2. Use a clamp to connect a solid copper 12 AWG ground wire to the

ground rod.

3. Route the ground wire to the operator.

4. Connect the ground wire to the operator’s frame.

Figure 7. Power Disconnect Box Wiring

110 VOLT

OPERATOR

POWER

DISCONNECT

BOX

BLACK

220 VOLT

OPERATOR

POWER

DISCONNECT

BOX

WHITE

GREEN

BLACK

WHITE

GREEN

HOT

NEUTRAL

GROUND

HOT

GROUND

Figure 5. Controller Access

LOOSEN KNOB

TO REMOVE

CONTROLLER

COVER

WARNING

ALL AC ELECTRICAL CONNECTIONS TO THE POWER SOURCE AND

THE OPERATOR MUST BE MADE BY A LICENSED ELECTRICIAN AND

MUST OBSERVE ALL NATIONAL AND LOCAL ELECTRICAL CODES

Figure 6. Manual Disconnect Lever

MANUAL DISCONNECT

SHIFTERLEVER

PULL TO DISENGAGE

LOCKINGLEVER

PUSH TO RIGHT TO

RE-ENGAGE OPERATOR

TO MANUALLY MOVE THE GATE,

PULL SHIFTERLEVERTO

DISENGAGE THE DRIVE TRAIN

GATE LIMIT SETTINGS WILL

NOT BE AFFECTED WHEN

GATE ISMANUALLY MOVED

PULL

PUSH

GSLG-A Slide Gate Operator Installation Guide - 6 - P1222 Revision X5 6-22-2011

LOOSEN SET SCREW ON

THE ADJUSTMENT NUT

ADJUSTMENT NUT

TO INCREASE TORQUE

TURN ADJUSTMENT NUT

CLOCKWISE ONE FLAT

THEN RE-TEST

TO DECREASE TORQUE

TURN ADJUSTMENT NUT

COUNTERCLOCKWISE

ONE FLAT THEN RE-TEST

TIGHTEN SET SCREW

DURINGTESTING

AND WHEN FINISHED !!!

LESS

Operator Setup (Cont.)

Open and Close Limit Adjustment

The limit nuts are not preset at the factory and must be adjusted

for the gate in each installation.The limit switches are activated

by two threaded nylon rotary limit nuts which are attached to

a threaded limit shaft driven by a chain and sprockets from

the main drive shaft. REMOVE THE CARDBOARD FILLER

BEFORE ADJUSTING THE LIMIT NUTS.

The Controller is factory setup for right hand installations.

The OPEN limit switch is the one closer to the front of the

operator. In left hand installations, the CLOSE limit switch is

the one closer to the front of the operator (see Figure 8).

Limit Nuts Rough Adjustment

Before running the operator, set the limit nuts as follows:

1. With the gate connected to the gate operator in a mid-travel position,

the power disconnect switch turned OFF, disconnect the operator

by using the manual disconnect lever, once the operator has been

disconnected, manually move the gate by hand to within a foot of

its fully open position (the foot of distance is necessary to allow for

coasting of the operator after the limit switch is tripped).

2. Once the gate is in this position, adjust the OPEN limit nut until it

activates the limit switch for open. Press down the detent plate and

rotate the nut along the threaded shaft (see Figure 9).

3. After setting the open limit, move the gate to one foot from fully

closed and repeat the process for the CLOSE limit nut.

Limit Nuts Fine Adjustment

After ﬁnishing the rough limit nut adjustments, reposition the

gate to approximately the center of travel.

1. Re-engage the operator using the disconnect handle.

2. Turn the power disconnect switch ON.

3. Stand clear of any moving parts and press the OPEN button.

4. After the gate opens, press the CLOSE button.

5. Observe the gate in both directions as it runs through each complete

cycle. Adjust the open or close limit nuts again if necessary. Fine levels

of adjustment can be made by adjusting a few teeth on the nut at a

time. If the gate stops during travel, you may need to adjust the Open or

Close Current Setting or the Maximum Run Timer (see Pages 12-13).

Torque Limiter Adjustments

Before adjusting the torque limiter, make sure the gate is in

good working condition. One person should be able to move

the gate by hand. Be certain the gate moves freely and

without binding throughout its travel. Torque limiters are set

light at the factory and must be adjusted during installation.

Adjust the torque limiter tight enough to keep it from slipping

during normal operation. See Figure 10.

To adjust the torque limiter in model GSLG-A:

1. Loosen the setscrew in the adjustment nut.

2. To increase the output, turn the adjustment nut clockwise

one ﬂat, or 1/6 turn, at a time until desired output is obtained.

To reduce the output, turn the adjustment nut counterclockwise one

ﬂat, or 1/6 turn, at a time until desired output is obtained.

3. Retighten the setscrew in the adjustment nut when ﬁnished.

PRESS DETENT

PLATE DOWN

ROTATE

LIMIT NUT

Figure 9. Setting the Limits

Figure 10. Torque Limiter Adjustment

CAUTION

If the operator is installed in a left-hand installation. Set the

Controller to left-hand operation BEFORE running the operator

for the ﬁne setting of the limit nuts. Failure to do so will result

in over-shooting the limit switches, and can cause damage to

the operator and/or gate. Refer to programming on Page 11.

LEFT-HAND INSTALLATION

OPEN LIMITCLOSE LIMIT

RIGHT-HAND INSTALLATION

OPEN LIMIT CLOSE LIMIT

LIMIT

NUTS

LIMIT

SHAFT

LIMIT

SWITCHES

FRONT OF

OPERATOR

Figure 8. Limit Box Assembly

GSLG-A Slide Gate Operator Installation Guide - 7 - P1222 Revision X5 6-22-2011

Controller Features

SHADOW/RESET

PROGRAMMING

BUTTONS

POWER

INDICATORS

DISPLAY

WHIP

ANTENNA

OPERATION

BUTTONS

OPERATION AND

PROGRAMMING

INDICATORS

ANTENNA

CONNECTOR

MOTOR

BOARD

COVER

INPUT

POWER

TERMINALS

ACCESSORY

POWER

TERMINALS

RESET

BUTTON

TERMINALS

SOLAR

PANEL

TERMINALS

BATTERY

TERMINALS

PLUG-IN

LOOP

DETECTOR

CONNECTORS

PRIMARY/

SECONDARY

COMM LINK

TERMINALS

SINGLE

INPUT

TERMINALS

FIRE DEPT

INPUT

TERMINALS

OPEN INPUT

TERMINALS

3-BUTTON

STATION

TERMINALS

OPEN AND CLOSE

OBSTRUCTION

INPUT TERMINALSREVERSE

INPUT

TERMINALS

OPEN LOOP

INPUT TERMINALS

REVERSE LOOP

INPUT TERMINALS

SHADOW/RESET LOOP

INPUT TERMINALS

LIMIT SWITCH

INPUT TERMINALS

ALARM

OUTPUT

TERMINALS

AC MOTOR

OUTPUT

TERMINALS

AUXILIARY

RELAY

TERMINALS

Figure 11. Controller Features

GSLG-A Slide Gate Operator Installation Guide - 8 - P1222 Revision X5 6-22-2011

Indicator Descriptions

INDICATOR DEFINITION INDICATION WHEN LIT

DURING NORMAL OPERATION

INDICATION WHEN LIT

DURING PROGRAMMING

OPERATION PROGRAMMING

24 VOLT INPUT

POWER LOW VOLTAGE AC POWER IS PRESENT

24 VOLT DC

ACCY POWER LOW VOLTAGE DC POWER IS PRESENT

OPEN

OPEN SIGNAL PRESENT FROM THE INTERNAL

RECEIVER OR AN EXTERNAL DEVICE

CONNECTED TO THE OPEN INPUT TERMINAL

CLOSE CLOSE SIGNAL IS PRESENT FROM A DEVICE

CONNECTED TO THE CLOSE INPUT TERMINAL

STOP STOP INPUT TERMINAL IS OPEN AND

NOT CONNECTED TO COMMON

PROGRAM CONTROLLER IS IN PROGRAMMING MODE

REVERSE DELAY SET SIGNAL FROM REVERSING DEVICE IS PRESENT SET REVERSE DELAY TIME

LOCKOUT ALARM SET CONTROLS AND OPERATOR ARE LOCKED OUT

BECAUSE OF EXISTING TROUBLE CONDITION SET RUN ALARM AND PRE-START ALARM

RADIO LEARN BUILT-IN RECEIVER IS DETECTING A RADIO

SIGNAL FROM A REMOTE CONTROL

TRANSMITTERS CAN BE ENTERED INTO

MEMORY (UP TO 40 TRANSMITTERS)

OPEN CURRENT SET MOTOR CURRENT HAS EXCEEDED THE

OPEN CURRENT SETTING WHILE OPENING SET MAXIMUM OPEN CURRENT

OPEN OBSTR MGT 2 SET

OPEN OBSTRUCTION TERMINAL CONNECTED

TO COMMON BY BEAM OR SAFETY EDGE, OR

SIGNAL FROM MGT OBSTACLE TRANSMITTER

SET MGT #2 FUNCTION

OPEN RELAY LH/RH SET OPEN RELAY IS ACTIVATED SET LEFT-HAND RIGHT-HAND OPERATION

OPEN LIMIT BRAKE DELAY OPEN LIMIT SWITCH IS ACTIVATED

CLOSE CURRENT SET MOTOR CURRENT HAS EXCEEDED THE

CLOSE CURRENT SETTING WHILE CLOSING SET MAXIMUM CLOSE CURRENT

CLOSE OBSTR MGT 1 SET

CLOSE OBSTRUCTION TERMINAL CONNECTED

TO COMMON BY BEAM OR SAFETY EDGE, OR

SIGNAL FROM MGT OBSTACLE TRANSMITTER

SET MGT #1 FUNCTION

CLOSE RELAY AUTO CLOSE SET CLOSE RELAY IS ACTIVATED SET AUTO-CLOSE TIME

CLOSE LIMIT AC DC SET CLOSE LIMIT SWITCH IS ACTIVATED SET MOTOR TYPE

SINGLE SET SINGLE TERMINAL CONNECTED TO COMMON

BY AN EXTERNAL PUSHBUTTON OR RADIO SET SINGLE BUTTON INPUT FUNCTION

MAX RUN SET MAXIMUM RUN TIMER HAS BEEN EXCEEDED SET MAXIMUM RUN TIME

COMM LINK SET DUAL OPERATOR CONNECTION DETECTED,

BLINKS IF CONNECTION HAS FAILED

MAINT ALERT SET MAINTENANCE IS REQUIRED ON OPERATOR SET MAINTENANCE ALERT CYCLE COUNT

"RL"

LEFT ORRIGHT

HAND OPERATION

"PM"

SINGLE OR

DUAL GATE

"AC"

AUTO CLOSE

TIMER

"RP"

RUN ALARM

PRE-START ALARM

"OC"

MAXIMUM OPEN

CURRENT

"CC"

MAXIMUM CLOSE

CURRENT

"AD"

ADVANCED

PROGRAMMING

"RT"

MAXIMUM

RUN TIMER

"SB"

SINGLE BUTTON

INPUT SETUP

"SM"

STAGGER

MODE

"ST"

STAGGER

TIME

"AR"

AUXILIARY

RELAY MODE

"RD"

REVERSE

DELAY TIME

"CT"

RESET CYCLE

COUNT

"MA"

MAINTENANCE ALERT

TRIGGER

"MT"

MID-TRAVEL

STOP POSITION

"RA"

RADIO

ENABLE

"TL"

LEARN

TRANSMITTERS

"TD"

DELETE

TRANSMITTERS

"ML"

LEARN MGT

TRANSMITTERS

"MD"

ERASE MGT

TRANSMITTERS

"CL"

RESET TO

FACTORY DEFAULTS

APEX FUNCTION DISPLAY INDICATIONS

MOTORTYPE

SELECTION

"MO"

"CP"

CONSTANT

PRESSURE MODE

"SP"

SHADOW LOOP

OPEN INHIBIT

"AT"

ANTI-TAILGATE

ENABLE

"BD"

BRAKE

DELAY TIME

Andere Handbücher für GSLG-A

Inhaltsverzeichnis

Andere Linear Torantrieb Handbücher

Linear

Linear GSLG-A Bedienungsanleitung

Beliebte Torantrieb Handbücher anderer Marken

DKS

DKS 6002 Bedienungsanleitung

GFA

GFA ELEKTROMAT SE 14.22-25,40 Bedienungsanleitung

DIGITALas

DIGITALas D-FORCE600VA Bedienungsanleitung

Mighty Mule

Mighty Mule MM560 Bedienungsanleitung

GFA

GFA ELEKTROMAT SE 15.48-25,40 Bedienungsanleitung

GFA

GFA ELEKTROMAT SE 6.24-25,40 Bedienungsanleitung

GFA

GFA ELEKTROMAT SE 9.32-25,40 Bedienungsanleitung