Linear DC1719A Kurzanleitung zur Einrichtung

dc1719af

DEMO MANUAL DC1719A

Description

LTC5569

300MHz to 4GHz 3.3V DUAL

ACTIVE DOWNCONVERTING MIXER

Demonstration circuit DC1719A is optimized for evaluation

of the LTC

5569 dual active downconverting mixer. Its RF

and LO input ports are internally matched to 50Ω from

1.4GHz to 3.3GHz, and from 1GHz to 3.5GHz, respectively.

The IF output uses a bandpass network followed by an

8:1 transformer to provide a 50Ω match at 190MHz. The

LTC5569 dual active mixer is optimized for diversity and for

MIMOreceiverapplicationsthatrequirelowpowerandsmall

size.Eachmixerincludes an independentLObufferamplifier,

an active mixer core, and a bias circuit with an enable pin.

The symmetry of the IC assures that a phase and ampli-

tude coherent LO is applied to each mixer. Broadband

integrated transformers on the RF and LO inputs provide

single-ended 50Ω interfaces. The differential IF outputs

allow convenient interfacing to differential IF filters and

amplifiers.

Design files for this circuit board are available at

http://www.linear.com/demo

BoarD photo

Figure 1. Test Setup for Mixer 2-Tone Measurements

L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of

Linear Technology Corporation. All other trademarks are the property of their respective owners.

aBsolute MaxiMuM ratings

Supply Voltage (VCCA, VCCB, IFA+, IFA–,

IFB+, IFB–)...................................................................4V

Enable Input Voltage (ENA, ENB) ......–0.3V to VCC + 0.3V

Mixer Bias Voltage (BIASA, BIASB)....–0.3V to VCC + 0.3V

LO Input Power (350MHz to 4.3GHz)...................10dBm

LO Input DC Voltage............................................... ±0.1V

RF Input Power (300MHz to 4GHz)......................15dBm

RF Input DC Voltage (RFA, RFB) ............................ ±0.1V

Operating Temperature Range (TC)........ –40°C to 105°C

Junction Temperature (TJ).................................... 150°C

Storage Temperature Range .................. –65°C to 150°C

CAUTION: This part is sensitive to electrostatic discharge

(ESD). Observe proper ESD precautions when handling

the LTC5569.

Downloaded from Arrow.com.

dc1719af

DEMO MANUAL DC1719A

notes on test equipMent anD setup

quick start proceDure

• Use high performance signal generators with low

harmonic outputs for 2-tone measurements to avoid

distortion. Otherwise, lowpass filters at the signal gen-

erator outputs should be used to suppress harmonics.

• Highqualitycombinersshouldbeusedtopresenta

broadband 50Ω termination on all ports as well as

provide good port-to-port isolation. Attenuator pads

may be used on the inputs to the combiner and the RF

input port of the LTC5569 mixer, as shown in Figure1.

Adding attenuator pads further improves source iso-

lation and helps prevent the signal generators from

producing intermodulation products.

• Spectrum analyzers can produce significant internal

distortion products if they are overdriven. Generally,

spectrum analyzers are designed to operate at their

best with about –30dBm to –40dBm at their input. The

spectrum analyzer’s input attenuation setting should

be used to avoid saturating the instrument. Set the

spectrum analyzer’s input attenuation depending on

the spectrum analyzer used.

• Before performing measurements on the DUT, the

system performance should be evaluated to ensure

that a clean input signal is obtained and that the spec-

trum analyzer’s internal distortion is minimized.

parts list

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

1 2 C1, C2 0402 2.7pF ±0.25pF 50V NPO AVX, 04025A2R7CAT2A

2 1 C5 CAP, 0402 3.9pF ±0.1pF 50V NPO AVX, 04025A3R9BAT

3 4 C7, C8, C9, C10 CAP, 0402 10nF 10% 25V X7R AVX, 04023C103KAT

4 1 C11 CAP, 0603 2.2µF 10% 6.3V X5R AVX, 06036D225KAT

5 5 J1, J2, J3, J4, J5 CONN, BNC, SMA 50Ω EDGE-LANCH E. F. JOHNSON, 142-0701-851

6 4 L1, L2, L3, L4 0603 180nH 2% COILCRAFT, 0603HP-R18XGL

7 0 R1, R2, R3, R4 RES, 0402 OPTION OPTION

8 4 TP1, TP2, TP3, TP4 TURRET MILL-MAX, 2308-2-00-80-00-00-07-0

9 2 T1, T2 XFMR, WIDEBAND 2MHz TO 500MHz MINI-CIRCUITS, TC8-1+

10 1 U1 IC, DUAL ACTIVE DOWNCONVERTING MIXER LINEAR TECHNOLOGY, LTC5569IUF

1. Connect all test equipment as shown in Figure 1.

2. Set the power supply output voltage to 3.3V, and set

the current limit to 250mA.

3. Connect the VCC pin to the 3.3V supply. Connect ENA

to the 3.3V supply.

BE SURE TO CONNECT THE VCC PIN

BEFORE

THE

ENA PIN TO ENSURE THAT THE PART DOES NOT GET

DAMAGED. ALSO, REMOVE POWER FROM ENA PIN

BEFORE

REMOVING POWER FROM THE VCC PIN.

4. Set the LO signal generator to provide a 2140MHz CW

signal at about 0dBm to the demo board’s LO port.

5. Set the RF signal generators to provide one 1950MHz

CW signal and one 1951MHz CW signal. The signals

should be applied to the 2-way combiner. The output

of the combiner should be applied to the demo board’s

RFA port. The two tones should be set to about –6dBm

each at the mixer’s RF input port.

6. Set the spectrum analyzer’s center frequency to

190MHz.

7. Perform various measurements (conversion gain,

OIP3, LO leakage, etc.).

Downloaded from Arrow.com.Downloaded from Arrow.com.

dc1719af

DEMO MANUAL DC1719A

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-

tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.

scheMatic DiagraM

Figure 2. Dual Active Mixer

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

dc1719af

DEMO MANUAL DC1719A

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

(408) 432-1900 ●FAX: (408) 434-0507 ●www.linear.com

LT 0611 • PRINTED IN USA

DEMONSTRATION BOARD IMPORTANT NOTICE

Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:

This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT

OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete

in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety

measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union

directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.

If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date

of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims

arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all

appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or

agency certified (FCC, UL, CE, etc.).

No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,

customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.

LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.

Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and

observe good laboratory practice standards. Common sense is encouraged.

This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC applica-

tion engineer.

Mailing Address:

Linear Technology

1630 McCarthy Blvd.

Milpitas, CA 95035

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Andere Linear Hauptplatine Handbücher

Linear

Linear 1524A-A Bedienungsanleitung

Linear

Linear Analog Devices LT3960 Kurzanleitung zur Einrichtung

Linear

Linear DC1630A Kurzanleitung zur Einrichtung

Linear

Linear DC1735A Kurzanleitung zur Einrichtung

Linear

Linear 747 Bedienungsanleitung

Linear

Linear ADI Power SCP-LT3461-EVALZ Kurzanleitung zur Einrichtung

Linear

Linear DC2048A Kurzanleitung zur Einrichtung

Linear

Linear DC2230A-B Kurzanleitung zur Einrichtung

Linear

Linear ADI Power SCP-LT1962-EVALZ Kurzanleitung zur Einrichtung

Linear

Linear DC1685A Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC2543B Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices DC2749A Bedienungsanleitung

Linear

Linear DC2073A Kurzanleitung zur Einrichtung

Linear

Linear DC266B-A Kurzanleitung zur Einrichtung

Linear

Linear DC1194A Kurzanleitung zur Einrichtung

Linear

Linear ADI Power DC3080A-KIT Kurzanleitung zur Einrichtung

Linear

Linear DC2033A Kurzanleitung zur Einrichtung

Linear

Linear DC2002A Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC2631A Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices DC1842B Kurzanleitung zur Einrichtung

Linear

Linear DC2007A-B Kurzanleitung zur Einrichtung

Linear

Linear DC1395A Bedienungsanleitung

Linear

Linear Analog Devices DC2732A Kurzanleitung zur Einrichtung

Linear

Linear DC951A Kurzanleitung zur Einrichtung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung