Linear Analog Devices LTC4040 Kurzanleitung zur Einrichtung

DEMO MANUAL DC2118B

Rev. 0

DESCRIPTION

LTC4040

Battery Charger and Backup

Power Manager

Demonstration circuit 2118B is a combination step-down

battery charger and step-up battery backup regulator

using the LT C

4040 monolithic system power manager.

The DC2118B has an input voltage range from 4.8V to

5.5V with overvoltage protection (OVP) to 40V, as limited

by the external MOSFET. The input current is monitored to

prioritize the load up to the 2.5A threshold before charge

current is reduced.

Battery Charging

As initially configured, DC2118B is programmed for 2A

charge current limit when in charge mode. The charge

voltage is jumper-selectable in 8 discrete steps from

3.45V to 3.6V for LiFePO4chemistry or 3.95V to 4.1V for

Li-ion chemistry, according to the F2/F1/F0 programming

input settings.

The charge current limit is adjustable via the PROG pin

resistor. End-of-charge status is triggered by current

falling below C/8 and indicated by the CHRG LED. The

All registered trademarks and trademarks are the property of their respective owners.

PERFORMANCE SUMMARY

optional NTC input provides temperature fault detection

and status indicated by the FAULT LED. Charging can be

enabled/disabled with the ENCHG jumper.

Battery Backup

Following an input power failure, the circuit automatically

shifts to battery backup boost mode to regulate the VSYS

output rail. The backup mode system output voltage is ini

tially programmed for 5V. The input power failure status

is indicated by the PFO LED.

If VSYS ever falls below the programmed reset threshold

voltage, the RST LED will change states to indicate the

need to reset the system and recharge the battery. Backup

regulation can be enabled/disabled with the ENBST jumper.

For convenience, all LEDs can be disabled with the LED

jumper to reduce the quiescent current of the system.

Design files for this circuit board are available.

Specifications are at TA= 25°C

PARAMETER CONDITIONS VALUE

Charge Mode

Input Voltage Range 4.8V to 5.5V

Overvoltage Protection Range Limited by Q1 BVDSS 5.5V to 40V

Input Current Limit R7 = 10mΩ 2.5A

Default Charging Voltage F2 = 1 (Li-Ion), F1 = 1, F0 = 1 4.10V

Charging Current RPROG = 1.00k 2.0A

Safety Timer Period F2 = 1 (Li-Ion) 4Hr

F2 = 0 (LiFePO4) 2Hr

Backup Mode

DCIN Input Power Fail Threshold R2 = 357k, R27 = 121k, DCIN Falling 4.8V

System Output Voltage R4 = 1.69M, R5 = 324k 5.0V

Backup Battery Voltage Range 2.7V to 5.0V

System Reset Threshold R4 = 1.69M, R5 = 324k, VSYS Falling 4.6V

Backup Boost Efficiency VBAT = 3.6V, ISYS = 2A, VOUT = 5V 89%

DEMO MANUAL DC2118B

Rev. 0

QUICK START PROCEDURE

Demonstration circuit 2118B is easy to set up to evalu-

ate the performance of LTC4040. Refer to Figure2 for

proper measurement equipment setup and follow the

procedurebelow.

1. The jumpers are set as below for a typical 4.1V charg-

ing application:

JP1 NTC INT

JP2 ENCHG ON

JP3 ENBST ON

JP4 F1 1

JP5 F0 1

JP6 LEDS ON

JP7 F2 1

2. With all power off, connect the input supply, system

load, and meters as shown in Figure3.

Charge Mode

3. Connect the battery as shown in Figure3 to charge at

4.1V, 2A. For alternate charge voltage settings, refer

to Table1.

4. Turn on the input power supply to evaluate charge

mode. Adjust the input voltage and current limit to

the desired value.

NOTE: While DC2118B is robust to overvoltage condi-

tions up to 40V on DCIN, DO NOT exceed this limit or

damage may occur to MOSFET Q1 and IC U1.

5. Turn on and adjust the system load as necessary.

Charging current will be limited when input current

exceeds 2.5A.

6. The CHRG LED will toggle off when the charge current

has dropped below 250mA. The timer will continue to

run and charging will continue until the timer period

ends. Multiple timer periods may be necessary to fully

charge a large capacity battery, such as the one used

to obtain Figure1.

7. If the battery voltage does not increase above the low

battery threshold during the precondition time or the

thermistor value exceeds the normal range, CHRG

will toggle off and FAULT will toggle on indicating a

badbattery.

Backup Mode

8. Turn off the input power supply to evaluate back-

upmode.

9. The PFO LED will toggle on indicating input power

failure.

10. Adjust the system load as necessary.

Figure1. Typical Battery Charge Cycle Figure2. Typical Battery Discharge Cycle

PERFORMANCE SUMMARY

TIME (Hrs)

BAT

(A)

2.25

2.00

1.50

1.00

0.50

1.75

1.25

0.75

0.25

BAT

+ V

CHRG

(V)

4.2

4.0

3.6

3.2

2.8

3.8

3.4

3.0

2.6

2.4

5 93 7

dc2118b F01

104 82 61

9600mAh Li-Ion

VIN = 5V

RPROG = 1.00k

TIMER

RESTART

TIMER

START

CHRG

VBAT

IBAT

C/8

TERMINATION

TIME (Hrs)

0:00

BAT

(V)

BAT

(A)

1:30

dc2118b F02

2:302:001:000:30

9600mAh Li-Ion

VSYS = 5V

ISYS = 2A

POWER

FAIL

BACKUP

STARTED

VSYS

IBAT VBAT

DEMO MANUAL DC2118B

Rev. 0

QUICK START PROCEDURE

Figure3. Proper Measurement Equipment Setup

11. Total backup runtime is based on battery capacity,

circuit efﬁciency, and system load. Figure2 shows

an example discharge curve with constant current

systemload.

12. WhenVSYS fallsbelow7.5%of the programmed value,

or 4.6V, then RST will toggle on.

Optional

1. Usean externalthermistorconnected betweenEXTNTC

and GND as shown in Figure3, with the NTC jumper,

JP1, set to EXT.

2. Change the setting of the ENCHG, JP2, or ENBST,

JP3, jumpers to enable/disable charging and backup

boostrespectively.

3. Monitor the PROG pin voltage for a scaled representa-

tion of the instantaneous charge current according to

the relationship:

IBAT =

2000 • V

PROG

RPROG

Where RPROG = R6 = 1kΩ.

4. MonitortheCLPROGpinvoltageforascaledrepresenta-

tion of the instantaneous total input current according

to the relationship:

IVIN =

CLPROG

32 • R

Where RS= R7 = 10mΩ.

5. All status LEDs can be disconnected to reduce the

quiescent current by setting the LEDS jumper, JP6

toOFF.

6. External VDD can be used by connecting to EXTVDD

and installing 0Ω for R16.

Table1. Battery Charge Voltage Jumper Settings

JP7 JP5 JP4

F2 = 1 (Li-Ion) F2 = 0 (LiFePO4) F1 F0

3.95 3.45 0 0

4.00 3.50 0 1

4.05 3.55 1 0

4.10 3.60 1 1

DEMO MANUAL DC2118B

Rev. 0

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 1 CIN1 CAP., X7R, 0.1µF, 10%, 50V, 0805 AVX, 08055C104KAT4A

2 2 COUT1, COUT2 CAP., X5R, 100µF, 20%, 10V, 1210 MURATA, GRM32ER61A107ME20L

3 1 C2 CAP., X7R, 2.2µF, 10%, 6.3V, 0805 MURATA, GRM21BR70J225MA01L

4 1 C3 CAP., X5R, 10µF, 20%, 10V, 0603 AVX, 0603ZD106MAT2A

5 2 C7, C9 CAP., X7R, 0.1µF, 10%, 10V, 0603 AVX, 0603ZC104KA72

6 1 L1 INDUCTOR, 2.2µH COILCRAFT, XAL5030-222ME

7 1 Q2 XSTR, MOSFET N-CHANNEL, 20-V VISHAY, SiS424DN-T1-GE3

8 1 R2 RES., 357k, 1/16W, 1%, 0402 VISHAY, CRCW0402357KFKED

9 1 R4 RES., 1.69MΩ, 1/16W, 1%, 0402 VISHAY, CRCW04021M69FKED

10 1 R5 RES., 324k, 1/16W, 1%, 0402 VISHAY, CRCW0402324KFKED

11 1 R6 RES., 1.00k, 1/10W, 1%, 0603 VISHAY, CRCW06031K00FKED

12 1 R7 RES., 0.01Ω, 1/4W, 1%, 1206 VISHAY, WSL1206R0100FEB

13 1 R8 RES., 10k, 1/16W, 1%, 0402 VISHAY, CRCW040210K0FKED

14 1 R11 RES., 0Ω JUMPER, 0402 VISHAY, CRCW04020000Z0ED

15 1 R25 RES., 1Ω, 1/8W, 5%, 0805 VISHAY, CRCW0805100RJNEA

16 1 R27 RES., 121k, 1/16W, 1%, 0402 VISHAY, CRCW040260K4FKED

17 1 U1 I.C., LTC4040EUFD ANALOG DEVICES, LTC4040EUFD#PBF

Additional Demo Board Circuit Components

1 0 C4, C6 CAP., 0402 OPT

2 1 C5 CAP., X5R, 0.1µF, 10%, 10V, 0402 MURATA, GRM155R71A104KA01J

3 1 D1 DIODE, SCHOTTKY NXP, BAT46WJ

4 1 D3 DIODE, LED, SMT, RED, 0603 LITE-ON, LTST-C193KRKT-5A

5 2 D4, D5 DIODE, LED, SMT, ORANGE, 0603 LTIE-ON, LTST-C193KFKT-5A

6 1 D6 DIODE, LED, SMT, GREEN, 0603 LITE-ON, LTST-C193KGKT-5A

7 1 Q1 XSTR, MOSFET N-CHANNEL, 40-V VISHAY, SiS488DN-T1-GE3

8 1 RNTC RES., 10k, 1/16W, 1%, 0402 VISHAY, CRCW040210K0FKED

9 1 R1 RES., 6.2k, 1/8W, 5%, 0805 VISHAY, CRCW08056K20JNEA

10 0 R12, R13, R16 RES., 0402 OPT

11 4 R21-R24 RES., 390Ω, 1/16W, 5%, 0402 VISHAY, CRCW0402390RJNED

Hardware: For Demo Board Only

1 18 E1, E2, E4-E19 TEST POINT, TURRET, 0.094" MILL-MAX, 2501-2-00-80-00-00-07-0

2 7 JP1-JP7 3 PIN JUMPER, 2mm SAMTEC TMM-103-02-L-S

3 7 XJP1-XJP7 SHUNT, 2mm SAMTEC 2SN-BK-G

4 4 STAND-OFF STAND-OFF, NYLON KEYSTONE, 8834(SNAP ON)

DEMO MANUAL DC2118B

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications

subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

SCHEMATIC DIAGRAM

D D

C C

B B

A A

VSYS

GND

VBAT

GND

DCIN

EXTNTC

4.8V - 5.5V

BSTOFF

CHGOFF

F2=1(LI-ION) F2=0(LIFEP04) F1 F0

3.95V 3.45V 0 0

4.00V 3.50V 0 1

4.05V 3.55V 1 0

4.10V 3.60V 1 1

FAULT

PFO

RST

CHRG

CLPROG

NOTES: UNLESS OTHERWISE SPECIFIED,

1. ALL RESISTORS ARE 0402, 1%.

EXTVDD

2. ALL CAPACITORS ARE 0603, X7R.

OV PROTECTION

GND

5V IN BACKUP

2A CHARGE

4. LIMITED BY Q1 VDS RATING.

SEE NOTE 4

PROG

(DEFAULT)

REV

Z P

DESCRIPTION DATE

REVISION HISTORY

06/13/19

ECO

1PROD

APPROVED

VIN

VSYS

VDD

VDD VDD VDD VDD

VSYS

VDD

DATE:

IC NO.

SHEET OF

TITLE: DEMO CIRCUIT SCHEMATIC,

APPROVALS

PCB DES.

APP ENG. Phone: 1-408-432-1900

Milpitas, CA 95035

1630 McCarthy Blvd.

For ADI Customer Use Only

CUSTOMER NOTICE

ANALOG DEVICES INC. HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT ANALOG DEVICES

INC. APPLICATIONS ENGINEERING FOR ASSISTANCE.

THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES INC. AND

SUPPLIED FOR USE WITH ANALOG DEVICES INC. PARTS.

SCALE = NONE

SIZE:

SKU NO. SCHEMATIC NO. AND REVISION:

PCA BOM:

PCA ASS'Y:

www.analog.com

Z P

LTC4040EUFD24

DC2118B

700-DC2118B_REV01

705-DC2118B_REV01

N/A

Thursday, June 13, 2019

710-DC2118B_REV01

BATTERY CHARGER BACKUP POWER MANAGER

M I

DATE:

IC NO.

SHEET OF

TITLE: DEMO CIRCUIT SCHEMATIC,

APPROVALS

PCB DES.

APP ENG. Phone: 1-408-432-1900

Milpitas, CA 95035

1630 McCarthy Blvd.

For ADI Customer Use Only

CUSTOMER NOTICE

ANALOG DEVICES INC. HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT ANALOG DEVICES

INC. APPLICATIONS ENGINEERING FOR ASSISTANCE.

THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES INC. AND

SUPPLIED FOR USE WITH ANALOG DEVICES INC. PARTS.

SCALE = NONE

SIZE:

SKU NO. SCHEMATIC NO. AND REVISION:

PCA BOM:

PCA ASS'Y:

www.analog.com

Z P

LTC4040EUFD24

DC2118B

700-DC2118B_REV01

705-DC2118B_REV01

N/A

Thursday, June 13, 2019

710-DC2118B_REV01

BATTERY CHARGER BACKUP POWER MANAGER

M I

DATE:

IC NO.

SHEET OF

TITLE: DEMO CIRCUIT SCHEMATIC,

APPROVALS

PCB DES.

APP ENG. Phone: 1-408-432-1900

Milpitas, CA 95035

1630 McCarthy Blvd.

For ADI Customer Use Only

CUSTOMER NOTICE

ANALOG DEVICES INC. HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT ANALOG DEVICES

INC. APPLICATIONS ENGINEERING FOR ASSISTANCE.

THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES INC. AND

SUPPLIED FOR USE WITH ANALOG DEVICES INC. PARTS.

SCALE = NONE

SIZE:

SKU NO. SCHEMATIC NO. AND REVISION:

PCA BOM:

PCA ASS'Y:

www.analog.com

Z P

LTC4040EUFD24

DC2118B

700-DC2118B_REV01

705-DC2118B_REV01

N/A

Thursday, June 13, 2019

710-DC2118B_REV01

BATTERY CHARGER BACKUP POWER MANAGER

M I

E14

0.1uF

0603

JP4

SiS424DN

JP2

OFF

ENCHG

R21

390

RED D5

ORG

R25

0805

ORG

6.2k

0805

R5 324k

R22

390

JP3

OFF

ENBST

COUT1

100uF

10V

1210

E12

RNTC

10k

JP6

OFF

LEDS

R23

390

5% R12

OPT

1.00k

0603

SiS488DN

E10

357k

LTC4040EUFD

FAULT

VIN 6

PFI

BSTFB 18

SW 22

SW 21

2PROG

CLPROG

VSYS 1

VSYS 24

BAT 23

CHGOFF

BSTOFF

RST

CLN 7

RSTFB 10

OVSNS 16

NTC 17

CHRG

IGATE 15

PFO

GND

R24

390

0.1uF

R16

OPT

GRN

10k

0.1uF

10V

R27

121k 1%

CIN1

0.1uF

50V

0805

OPT

2.2uH

COILCRAFT

XAL5030-222ME

0.01 1%

1206

BAT46WJ

E13

JP1

INT EXT

NTC

E15

R13

OPT

1.69M

E16

10uF, 10V

0603

JP5

2.2uF

6.3V

0805

JP7

E11

E18

R11

E19

SEE NOTE 3

COUT2

100uF

10V

1210

E17

OPT

DEMO MANUAL DC2118B

Rev. 0

 ANALOG DEVICES, INC. 2019

10/19

www.analog.com

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and

conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation

Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)

and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to

Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and

agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted

is expressly made subject to the following additional limitations:Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board;and (ii) permit any Third

Party to access the Evaluation Board. As used herein, the term “Third Party”includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is

NOT sold to Customer;all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all

be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of

use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile

or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited

to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS

Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF

LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS”AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY

DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS

LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING

BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE

HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States

federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts

(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits

to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Linear Hauptplatine Handbücher

Linear

Linear DC2230A-B Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices ADI Power DC2685B-KIT Kurzanleitung zur Einrichtung

Linear

Linear LTC3717 Bedienungsanleitung

Linear

Linear DC951A Kurzanleitung zur Einrichtung

Linear

Linear DC1719A Kurzanleitung zur Einrichtung

Linear

Linear DC2106A-B Kurzanleitung zur Einrichtung

Linear

Linear DC1892A Kurzanleitung zur Einrichtung

Linear

Linear DC1339 Bedienungsanleitung

Linear

Linear LTC2345 Kurzanleitung zur Einrichtung

Linear

Linear DC1198B-B Kurzanleitung zur Einrichtung

Linear

Linear 1524A-A Bedienungsanleitung

Linear

Linear DC2194A Kurzanleitung zur Einrichtung

Linear

Linear DC1630A Kurzanleitung zur Einrichtung

Linear

Linear ADI Power DC3080A-KIT Kurzanleitung zur Einrichtung

Linear

Linear ANALOG DEVICES DC2685B Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices DC2749A Bedienungsanleitung

Linear

Linear DC2007A-B Kurzanleitung zur Einrichtung

Linear

Linear LTC6602 Bedienungsanleitung

Linear

Linear DC1395A Bedienungsanleitung

Linear

Linear LTC1474 Kurzanleitung zur Einrichtung

Linear

Linear DC2002A Kurzanleitung zur Einrichtung

Linear

Linear DC2048A Kurzanleitung zur Einrichtung

Linear

Linear ADI Power SCP-LT3461-EVALZ Kurzanleitung zur Einrichtung

Linear

Linear Analog Devices DC2721A-B Kurzanleitung zur Einrichtung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung