Linksys BEFSR41 - EtherFast Cable/DSL Router Bedienungsanleitung

USER GUIDE

EtherFast®

Cable/DSL Router

with 4-Port Switch

Model No: BEFSR41

Table of Contents

EtherFast Cable/DSL Router with 4-Port Switch

About This Guide 1

Icon Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Online Resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Chapter 1: Product Overview 2

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 2: Advanced Conguration 3

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Security > Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Security > VPN Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Applications and Gaming > Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . .10

Applications & Gaming > Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Applications and Gaming > UPnP Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Appendix A: Troubleshooting 17

Appendix B: Specications 18

Appendix C: Warranty and Regulatory Information 19

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Règlement d’Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

EC Declaration of Conformity (Europe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

About This Guide

EtherFast Cable/DSL Router with 4-Port Switch

About This Guide

Icon Descriptions

While reading through the User Guide you may encounter

various icons designed to call attention to a specific item.

Below is a description of these icons:

NOTE: This check mark indicates that there is

a note of interest and is something that you

should pay special attention to while using the

product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is

something that could damage your property or

product.

WEB: This globe icon indicates a noteworthy

website address or e-mail address.

Online Resources

Most web browsers allow you to enter the web address

without adding the http:// in front of the address. This

User Guide will refer to websites without including http://

in front of the address. Some older web browsers may

require you to add it.

Resource Website

Linksys www.linksys.com

Linksys International www.linksys.com/international

Glossary www.linksys.com/glossary

Network Security www.linksys.com/security

Specifications are subject to change without notice.

Linksys and EtherFast are registered trademarks or

trademarks of Cisco Systems, Inc. and/or its affiliates in

product names are trademarks or registered trademarks

of their respective holders.

Chapter 1 Product Overview

EtherFast Cable/DSL Router with 4-Port Switch

Chapter 1:

Product Overview

Thank you for choosing the Linksys EtherFast Cable/DSL

Router with 4-Port Switch. The Router lets you access the

Internet through its four switched ports. You can also use

the Router to share resources such as computers, printers

and files. A variety of security features help to protect

your data and your privacy while online. Security features

include a Stateful Packet Inspection (SPI) firewall and

NAT technology. Configuring the Router is easy using the

provided browser-based utility.

Front Panel

Power (Green) The Power LED lights up and

will stay on while the Router is powered on.

It flashes when the Router goes through its

self-diagnostic mode during every boot-up or

upgrades its firmware.

1, 2, 3, 4 (Green) These numbered LEDs,

corresponding with the numbered ports on the

Router’s back panel, serve two purposes. If the

LED is continuously lit, the Router is successfully

connected to a device through that port. A

flashing LED indicates network activity over

that port.

Internet (Green) The Internet LED lights up

when there is a connection made through the

Internet port. A flashing LED indicates network

activity over the Internet port.

Back Panel

Reset There are two ways to reset the Router to

its factory default settings. Use a straightened

paper clip or similar object to press and hold the

Reset button for approximately five seconds.

You can also restore the defaults from the

Administration > Factory Defaults screen of the

Router’s web-based utility.

Internet The Internet port is where you will

connect your cable or DSL Internet connection.

1, 2, 3, 4 These Ethernet ports (1, 2, 3, 4)

connect the Router to computers on your wired

network and other Ethernet network devices.

Power The Power port is where you will

connect the power adapter.

Chapter 2 Advanced Configuration

EtherFast Cable/DSL Router with 4-Port Switch

Chapter 2:

Advanced Configuration

After setting up the Router with the Setup Wizard (located

on the CD-ROM), the Router will be ready for use. However,

if you’d like to change its advanced settings, use the

Router’s web-based utility. This chapter describes each

web page of the utility and each page’s key functions. You

can access the utility via a web browser on a computer

connected to the Router.

The web-based utility has these main tabs: Setup, Security,

Applications & Gaming, Administration, and Status.

Additional tabs will be available after you click one of the

main tabs.

NOTE: When first installing the Router, you

should use the Setup Wizard on the Setup

CD-ROM. If you want to configure advanced

settings, use this chapter to learn about the

web-based utility.

How to Access the Web-Based Utility

To accessthe web-based utility,launchthe web browseron

your computer, and enter the Router’s default IP address,

192.168.1.1, in the Address field. Then, press Enter.

A login screen will appear. Leave the User Name field

blank. The first time you open the web-based utility, use

the default password admin. (You can set a new password

from the Administration > Management screen.) Click OK

to continue.

Setup > Basic Setup

The first screen that appears is the Basic Setup screen. This

allows you to change the Router’s general settings.

Setup > Basic Setup

Internet Setup

The Internet Setup section configures the Router to your

Internet connection. Most of this information can be

obtained through your Internet Service Provider (ISP).

Internet Connection Type

Select the type of Internet connection your ISP provides

from the drop-down menu. These are the available types:

Obtain an IP Automatically

Static IP

PPPoE

RAS

PPTP

Heart Beat Signal

L2TP

Obtain an IP Automatically

By default, the Router’s Internet Connection Type is set to

Obtain an IP automatically, which should be kept only if

your ISP supports DHCP or you are connecting through a

dynamic IP address. (This option usually applies to cable

connections.)

Internet Connection Type > Obtain an IP Automatically

•

Chapter 2 Advanced Configuration

EtherFast Cable/DSL Router with 4-Port Switch

Static IP

If you are required to use a permanent IP address to

connect to the Internet, select Static IP.

Internet Connection Type > Static IP

IP Address Enter the Router’s IP address, as seen from the

Internet. This is provided by your ISP.

Subnet Mask Enter the Router’s subnet mask, as seen by

users on the Internet (including your ISP). This is provided

by your ISP.

Default Gateway Your ISP will provide you with the IP

address of the ISP server.

Static DNS 1-3 Your ISP will provide you with at least one

DNS (Domain Name System) server IP address.

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocol

over Ethernet) to establish Internet connections. If you are

connected to the Internet through a DSL line, check with

your ISP to see if they use PPPoE. If they do, you will have

to enable PPPoE.

Internet Connection Type > PPPoE

User Name and Password Enter the User Name and

Password provided by your ISP.

Service Name If provided by your ISP, enter the Service

Name.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

RAS

Remote Access Service (RAS) is a service that applies to

connections in Singapore only. For users in Singapore,

check with Singtel for information on RAS.

Internet Connection Type > RAS

User Name and Password Enter the User Name and

Password provided by Singtel.

RAS Plan Select the type of plan you have.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5minutes.

Keep Alive: Redial Period

If you select this option, the

Router will periodically check your Internet connection. If

you are disconnected, then the Router will automatically

re-establish your connection. To use this option, select

Keep Alive. In the Redial Period field, you specify how often

you want the Router to check the Internet connection. The

default value is 30 seconds.

Chapter 2 Advanced Configuration

EtherFast Cable/DSL Router with 4-Port Switch

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service that

applies to connections in Europe only.

Internet Connection Type > PPTP

IP Address Enter the Router’s IP address, as seen from the

Internet. This is provided by your ISP.

Subnet Mask Enter the Router’s subnet mask, as seen by

users on the Internet (including your ISP). This is provided

by your ISP.

Default Gateway Your ISP will provide you with the IP

address of the ISP server.

User Name and Password Enter the User Name and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5minutes.

Keep Alive: Redial Period

If you select this option, the

Router will periodically check your Internet connection. If

you are disconnected, then the Router will automatically

re-establish your connection. To use this option, select

Keep Alive. In the Redial Period field, you specify how often

you want the Router to check the Internet connection. The

default value is 30 seconds.

Heart Beat Signal

Heart Beat Signal is a service used in Australia only. If you

are using a Heart Beat Signal connection, check with your

ISP for the necessary setup information.

Internet Connection Type > Heart Beat Signal

User Name and Password Enter the User Name and

Password provided by your ISP.

Heart Beat Server Enter the IP address of your ISP’s Heart

Beat server. This is provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5minutes.

Keep Alive: Redial Period

If you select this option, the

Router will periodically check your Internet connection. If

you are disconnected, then the Router will automatically

re-establish your connection. To use this option, select

Keep Alive. In the Redial Period field, you specify how often

you want the Router to check the Internet connection. The

default value is 30 seconds.

L2TP

L2TP is a service that applies to connections in Israel only.

Internet Connection Type > L2TP

Server IP Address Enter the IP address of the L2TP server.

This is provided by your ISP.

User Name and Password Enter the User Name and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

Chapter 2 Advanced Configuration

EtherFast Cable/DSL Router with 4-Port Switch

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify

with your ISP before making any changes.

Optional Settings

Host Name and Domain Name These fields allow you to

supply a host and domain name for the Router. Some ISPs,

usually cable ISPs, require these names as identification.

You may have to check with your ISP to see if your

broadband Internet service has been configured with a

host and domain name. In most cases, leaving these fields

blank will work.

MTU MTU is the Maximum Transmission Unit. It specifies

the largest packet size permitted for Internet transmission.

Select Enable if you want to manually enter the largest

packet size that is transmitted. To have the Router select

the best MTU for your Internet connection, keep the

default setting, Disable.

Size When Manual is selected in the MTU field, this option

is enabled. Leave this value in the 1200 to 1500 range. The

default size depends on the Internet Connection Type:

DHCP, Static IP, or Telstra: 1500

PPPoE: 1492

PPTP or L2TP: 1460

Network Setup

The Network Setup section changes the settings on the

network connected to the Router’s Ethernet ports.Wireless

setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet

Mask as seen by your network.

•

Router IP

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic

Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A

DHCP server automatically assigns an IP address to each

computer on your network. If you choose to enable the

Router’s DHCP server option, make sure there is no other

DHCP server on your network.

Network Address Server Settings (DHCP)

Local DHCP Server DHCP is enabled by factory default.

If you already have a DHCP server on your network, or you

don’t want a DHCP server, then select Disable (no other

DHCP features will be available).

Start IP Address Enter a value for the DHCP server to

start with when is

suing IP addresses. Because the Router’s

default IP address is 192.168.1.1, the Start IP Address must

be 192.168.1.2 or greater, but smaller than 192.168.1.253.

The default is 192.168.1.100

Number of Address Enter the maximum number of

computers that you want the DHCP server to assign IP

addresses to. This number cannot be greater than 253.

The default is 50.

DHCP Address Range Displayed here is the range of

available IP addresses.

Client Lease Time The Client Lease Time is the amount

of time a network user will be allowed connection to the

Router with their current dynamic IP address. Enter the

amount of time, in minutes, that the user will be “leased”

this dynamic IP address. After the time is up, the user will

be automatically assigned a new dynamic IP address. The

default is 0minutes, which means one day.

Static DNS 1-3

The Domain Name System (DNS) is how

the Internet translates domain or website names into

Internet addresses or URLs.Your ISP will provide you with at

least one DNS Server IP address. If you wish to use another,

enter that IP address in one of these fields. You can enter up

to three DNS Server IP addresses here. The Router will use

these for quicker access to functioning DNS servers

Chapter 2 Advanced Configuration

EtherFast Cable/DSL Router with 4-Port Switch

WINS The Windows Internet Naming Service (WINS)

manages each PC’s interaction with the Internet. If you

use a WINS server, enter that server’s IP address here.

Otherwise, leave this blank.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS)

feature. DDNS lets you assign a fixed host and domain

name to a dynamic Internet IP address. It is useful when

you are hosting your own website, FTP server, or other

server behind the Router.

Before you can use this feature, you need to sign

up for DDNS service with a DDNS service provider,

www.dyndns.org or www.TZO.com. If you do not want to

use this feature, keep the default setting, Disabled.

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then

select DynDNS.org from the drop-down menu. If your

DDNS service is provided by TZO, then select TZO. The

features available on the DDNS screen will vary, depending

on which DDNS service provider you use.

DynDNS.org

Setup > DDNS > DynDNS.org

User Name Enter the User Name for your DDNS account.

Password Enter the Password for your DDNS account.

Host Name The is the DDNS URL assigned by the DDNS

service.

Internet IP Address The Router’s Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

TZO.com

Setup > DDNS > TZO

E-mail Address, TZO Password Key, and Domain

Name Enter the settings of the account you set up with

TZO.

Internet IP Address The Router’s Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a unique

piece of hardware for identification. Some ISPs will require

you to register a MAC address in order to access the

Internet. If you do not wish to re-register the MAC address

with your ISP, you may assign the MAC address you have

currently registered with your ISP to the Router with the

MAC Address Clone feature.

Setup > MAC Address Clone

Chapter 2 Advanced Configuration

EtherFast Cable/DSL Router with 4-Port Switch

MAC Clone

MAC Clone Service To have the MAC address cloned,

select Enable.

MAC Address Enter the MAC address registered with

your ISP here.

Clone Click this button to clone the MAC address of the

computer you are using.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Setup > Advanced Routing

This screen is used to set up the Router’s advanced

functions. Dynamic Routing automatically adjusts how

packets travel on your network. Static Routing sets up a

fixed route to another network destination.

Setup > Advanced Routing

Advanced Routing

NAT

Enable/Disable If this Router is hosting your network’s

connection to the Internet, keep the default, Enable. If

another router exists on your network, select Disable.

When the NAT setting is disabled, the Dynamic Routing

feature can be enabled.

Dynamic Routing (RIP)

Enable/Disable This feature enables the Router to

automatically adjust to physical changes in the network’s

layoutandexchangeroutingtableswiththeotherrouter(s).

The Router determines the network packets’ route based

on the fewest number of hops between the source and

the destination. When the NAT setting is enabled, the

Dynamic Routing feature is automatically disabled. When

the NAT setting is disabled, this feature is available. Select

Enable to use the Dynamic Routing feature.

Transmit RIP Version To use dynamic routing for

transmission of network data, select the protocol you

want: RIP1, RIP1-Compatible, or RIP2.

Receive RIPVersion Touse dynamic routingfor reception

of network data, select the protocol you want, RIP1 or

RIP2.

Static Routing

A static route is a pre-determined pathway that network

information must travel to reach a specific host or network.

Enter the information described below to set up a new

static route.

Select Entry To set up a static route between the Router

and another network, select a number from the drop-

down list. Click Delete Entry to delete a static route.

Destination IP Address Enter the IP address of the

remote network or host to which you want to assign a

static route.

Subnet Mask Enter the subnet mask. This determines

which portion of a Destination IP Address is the network

portion, and which portion is the host portion.

Gateway Enter the IP address of the gateway device that

allows for contact between the Router and the remote

network or host.

Hop Count Enter the maximum number of steps between

network nodes that data packets will travel. A node is any

device on the network, such as a computer, print server,

or router.

Interface Select the appropriate interface. This tells you

whether the Destination IP Address is on the LAN (Local

Area Network) or the Internet.

Click Show Routing Table to view the static routes you

have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet

Mask, Gateway, Hop Count,and Interfaceare displayed.

Click Refresh to update the information.

Click Save Settings to apply your changes, or click Cancel

Changes to cancel your changes.

Andere Handbücher für BEFSR41 - EtherFast Cable/DSL Router

Inhaltsverzeichnis

Andere Linksys Netzwerk-Router Handbücher

Linksys

Linksys HPRO200 Bedienungsanleitung

Linksys

Linksys WRT100 - RangePlus Wireless Router Bedienungsanleitung

Linksys

Linksys SPA2100 Bedienungsanleitung

Linksys

Linksys EA8500-EU Bedienungsanleitung

Linksys

Linksys AC2600 Bedienungsanleitung

Linksys

Linksys WET54G V3 Bedienungsanleitung

Linksys

Linksys RVS4000 Bedienungsanleitung

Linksys

Linksys BEFN2PS4 - EtherFast Cable/DSL And Voice... Original Betriebsanleitung

Linksys

Linksys BEFSR41W Bedienungsanleitung

Linksys

Linksys WAG120N Bedienungsanleitung

Linksys

Linksys WAG54G - Wireless-G ADSL Gateway Wireless... Bedienungsanleitung

Linksys

Linksys WRT54G - Wireless-G Broadband Router... Kurzanleitung

Linksys

Linksys SRW208G Bedienungsanleitung

Linksys

Linksys R 72 Bedienungsanleitung

Linksys

Linksys WET54Gv2 Bedienungsanleitung

Linksys

Linksys AC5400 Bedienungsanleitung

Linksys

Linksys BEFSR11 - EtherFast Cable/DSL Router Bedienungsanleitung

Linksys

Linksys E56000 Bedienungsanleitung

Linksys

Linksys EA4500 V3 Bedienungsanleitung

Linksys

Linksys SLM2024 Bedienungsanleitung

Linksys

Linksys BEFVP41 - EtherFast Cable/DSL VPN Router Bedienungsanleitung

Linksys

Linksys WRT320N - Wireless-N Gigabit Router Wireless Bedienungsanleitung

Linksys

Linksys BEFSX41 - Instant Broadband EtherFast Cable/DSL Firewall... Original Betriebsanleitung

Linksys

Linksys EG0801SK - EtherFast Network Starter Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise