Linksys EA9300 Bedienungsanleitung

Linksys Wi-Fi Router Page 1 of 9

Reviewer Guide

Linksys EA9300

Linksys AC4000 MU-MIMO TRI-BAND ROUTER

Linksys Wi-Fi Router Page 2 of 9

Reviewers Guide

Linksys EA9300

MAX-STREAM AC4000 MU-MIMO TRI-BAND ROUTER

Features to look for:

Tri-Band Design with three dedicated Wi-Fi bands delivering combined speed up to 4 Gbps ― double the

capacity of 5 GHz band comparing to dual-band wireless routers

Smart Connect intelligently chooses the best radio band for each wireless device to ensure fast and

optimized performance

1.8 GHz High-Performance Quad-Core Processor to drive the fastest wired and wireless network

speeds

Powerful 3x3 AC Wi-Fi Radios with MU-MIMO delivering up to 6 simultaneous MU-MIMO streams ―

gaming and streaming on multiple devices at the same time without speed degradation and wasted

bandwidth

Six Adjustable Antennas for wide, omnidirectional coverage in very large single or multi-story homes

Two USB 3.0 Ports provide flexible network access storage solution and fast data transfer of photos,

video, data files across your network ―giving you the ultimate media streaming experience.

Linksys Smart Wi-Fi: Access and control your home network from anywhere using a web browser or

mobile device

Auto Firmware Update gives you peace-of-mind of knowing your router is always current with the latest

features and security updates

Additional Features:

•Concurrent tri-band wireless operation (750 + 1625 + 1625 Mbps)*

•High-power wi-fi amplifiers

•Advanced beamforming technology

•Data transfer rates of up to 750 Mbps on 2.4GHz band (3 spatial streams with 1024-QAM)*

•Data transfer rates of up to 1625 Mbps on each 5GHz band (3 spatial streams with 1024-QAM)*

•Four gigabit LAN ports + one gigabit WAN port

•Integrated DHCP server with dynamic and static IP address assignment

•PPTP, IPSec and L2TP pass-through

•Storage features for external USB hard disk and flash drives (supports FAT, FAT32, NTFS, and HFS+)

•UPnP IGD and media server

•Supports DLNA for home media management

•Virtual USB support

•Wall mountable

* Specifications subject to change without notice. Actual performance may vary. Performance is dependent on products used, interference,

and other external conditions.

Linksys Wi-Fi Router Page 3 of 9

Installation of EA9300

The new Linksys MAX-STREAM AC4000 MU-MIMO Tri-Band Router can be configured with Linksys Smart Wi-Fi router

setup. Plug in the router to a power source with the provided power adapter and power cord. Wait until the illuminated

Linksys logo on the top of the router stops blinking and is solid white.

To configure the router for the first time:

1. Connect to the secured wireless network shown on the label on the bottom of the router (“Wi-Fi Name”). Select

the option to automatically connect to this network in the future.

2. Open a web browser to launch Linksys Smart Wi-Fi router setup instructions. Follow the on-screen instructions

to complete your router setup. If you do not see the setup instructions, type 192.168.1.1 in the address bar.

3. If you would like to manually configure your router, click on the link “Manual Configuration”at the lower left

corner. The router will prompt you for router password. The default router password is admin.

Linksys Wi-Fi Router Page 4 of 9

4. In Smart Wi-Fi Tools, go to Wireless, turn off Smart Connect and give 2 different network names to 5GHz1and

5GHz2, then click Apply. This is for demonstration of the performance of each individual frequency band in the

following tests.

General Suggestions

Linksys Wi-Fi Router Page 5 of 9

In order to get consistent and repeatable results, we suggest you control the variables of the test:

oTurn off all interfering devices, for example, wireless routers/access point/wireless range extenders that will not

participate in the test, Bluetooth devices (e.g. cell phone) and microwave ovens.

oUse the same location, time of day and equipment

Single-Client Performance Testing

Objective: To demonstrate the performance brought by 3x3 wireless technology.

We suggest you to use the following setup to conduct performance test:

- Configure the router with the following settings:

oUse WPA2-Personal if you wish to conduct the test with wireless security enabled

oSet Network Mode to Mixed

oIf you are testing 5GHz (802.11ac), set Channel Width to 80 MHz

oIf you are testing 2.4GHz (802.11n), set Channel Width to Auto

oSelect a channel that has the least interference

oSet QoS and Parental Controls set to Disabled

- Place EA9300 and Computer #2, the wireless client, about five (5) meters apart from each other

- Connect Computer #1 with the built-in Gigabit Ethernet port to one of the EA9300’s Ethernet (LAN) ports

- Connect Computer #2 wirelessly to one of the three wireless networks of EA9300. Computer #2 should be

equipped with a stable 3x3 802.11ac wireless adapter, for example, Macbook Pro (“late 2013” models or later).

Please do not use Linksys WUSB6100M to conduct this 3x3 single-client performance test.

oTo test the performance of 802.11ac, connect to one of the two 5GHz networks

- Download iPerf3 (in zip file) from https://iperf.fr/iperf-download.php to both computers and unzip the file.

- IMPORTANT: Disable firewall, auto software update, screen saver and power save (auto sleep) on all computers.

To run the test:

On Computer #1, open a command prompt window. Change the current directory to the location where iPerf is installed.

Then, execute the following iPerf command at the command prompt.

iperf3 -s -f m -i 1

On Computer #2, open a command prompt windows. Change the current directory to the location where iPerf is installed.

Then, execute the following iPerf command at the command prompt.

iperf3 -c <IP address of Computer #1> -fm-i1-t 60 -w 1M -P 1

(For example, iperf3 -c 192.168.1.105 -fm-i1-t 60 -w 1M -P 1)

MU-MIMO Testing

Objective: To demonstrate the benefit of MU-MIMO over SU-MIMO.

Linksys Wi-Fi Router Page 6 of 9

To demonstrate the benefit of MU-MIMO, first, turn off EA9300’s Smart Connect to make sure all the wireless clients are

on the same frequency band. See Step 4 in “To configure the router for the first time” for instructions of turning off Smart

Connect.

For the best performance, we recommend the following settings on the 5GHz networks (both 5GHz1and 5GHz2) of

EA9300:

WPA2-Personal if you wish to conduct the test with wireless security enabled

Network Mode set to Mixed

Channel Width set to 80 MHz

Select a channel that has the least interference

QoS and Parental Controls set to Disabled

Linksys WUSB6100M is a USB wireless adapter that supports MU-MIMO. Prepare two computers and install Linksys

WUSB6100M wireless adapter on each computer. See “Installation of WUSB6100M” at the end of this document for

instructions.

Then, set up the MU-MIMO test in the following way:

Two computers (clients), which have Linksys WUSB6100M installed, and EA9300 form a right-angled triangle (right

triangle) as shown in the above diagram. The distance between the client and the router should be 6 feet or more.

Another computer (Computer #3) connected to EA9300’s one of the four Ethernet ports from the computer’s built-in

Gigabit Ethernet port is not shown in the above diagram. Computer #1 and #2 are wirelessly connected to one of the two

5GHz networks of EA9300. Make sure Computer #1 and #2 are connected to the same 5GHz network.

Download iPerf3 (in zip file) from https://iperf.fr/iperf-download.php to each of the three computers and unzip the file.

IMPORTANT: Disable firewall, auto software update, screen saver and power save (auto sleep) on all computers.

A. With MU-MIMO enabled (factory default setting)

On computer #1 and #2, open a command prompt window. Change the current directory to the location where iPerf3 is

installed. Then, execute the following iPerf3 command at the command prompt on each of these computers.

iperf3 -s -f m -i 1

On computer #3, open 2 command prompt windows. Change the current directory to the location where iPerf3 is installed

in each command prompt window. Then, execute the following iPerf3 command at the command prompt in each of the

command prompt window simultaneously (substitute with the actual IP address of Computer #1 and #2 respectively).

iperf3 -c <IP address of Computer #1 or #2>-fm-i1-t 60 -w 1M -P 1

(For example, iperf3 -c 192.168.1.105 -fm-i1-t 60 -w 1M -P 1)

Linksys Wi-Fi Router Page 7 of 9

B. With MU-MIMO disabled (SU-MIMO case)

Follow the instructions at the end of this section to disable MU-MIMO on EA9300. Then, repeat the above test.

C. MU-MIMO vs SU-MIMO Comparison

Computer #1

Computer #2

Aggregate

SU-MIMO

MU-MIMO

% Increase

Δ1

Δ2

Δa

󰇛󰇜 



󰇛󰇜 

   



For example:

Computer #1

Computer #2

Aggregate

SU-MIMO

153 Mbps

306 Mbps

MU-MIMO

245 Mbps

251 Mbps

496 Mbps

% Increase

60%

64%

62%

To enable/disable MU-MIMO support in EA9300:

From a computer that is connected to EA9300, log in to the router at 192.168.1.1. Then, visit the following router

configuration page (please make sure you have logged in to the router before visiting this configuration page):

http://192.168.1.1/ui/dynamic/advanced-wireless.html

Linksys Wi-Fi Router Page 8 of 9

(Note: This Advanced Wireless Settings page is for testing purpose and it’s not intended for end users. Please do not

publish the link of this configuration page to the general public.)

Select Broadcom tab. Toggle MU-MIMO support by checking (enable) or unchecking (disable) both boxes next to “MU-

MIMO Enabled”, then click the Apply button. MU-MIMO is enabled by default in EA9300.

Installation of WUSB6100M (for MU-MIMO test only)

Linksys WUSB6100M is a USB wireless adapter that supports MU-MIMO. You only need to install this

wireless adapter if you are going to conduct MU-MIMO test. To install:

1. Insert WUSB6100M wireless adapter into an available USB port on your computer.

2. Watch the computer monitor as the device automatically installs.

3. If the wireless adapter does not install automatically, use the provided CD and run the driver installation file

(also available at linksys.com/support/wusb6100M).

Linksys Wi-Fi Router Page 9 of 9

Note: Once the installation of WUSB6100M is successful, remember to disable the computer’s built-in wireless

adapter to avoid accidental use of the incorrect wireless adapter in the MU-MIMO test. Go to Control Panel >

Network and Sharing Center > Change adapter settings. Then, right click the built-in wireless adapter and

click Disable.

________________________________________________________________________________

If you have any questions please free to contact Karen Sohl: 714 658-7330 k[email protected]

Inhaltsverzeichnis

Andere Linksys Netzwerk-Router Handbücher

Linksys

Linksys BEFVP41 - EtherFast Cable/DSL VPN Router Bedienungsanleitung

Linksys

Linksys WT54GV22 Bedienungsanleitung

Linksys

Linksys EF1324 Bedienungsanleitung

Linksys

Linksys BEFW11S4 ver.3 Leitfaden

Linksys

Linksys SPA2100 Bedienungsanleitung

Linksys

Linksys Instant PowerLine PLEBR10 Bedienungsanleitung

Linksys

Linksys E7350 Bedienungsanleitung

Linksys

Linksys SFE1000P Bedienungsanleitung

Linksys

Linksys EG0801SK - EtherFast Network Starter Bedienungsanleitung

Linksys

Linksys Velop MX4000 Series Bedienungsanleitung

Linksys

Linksys R 72 Bedienungsanleitung

Linksys

Linksys E2500 Bedienungsanleitung

Linksys

Linksys AC2600 Bedienungsanleitung

Linksys

Linksys EA4500 Bedienungsanleitung

Linksys

Linksys max-stream ac-1900 Bedienungsanleitung

Linksys

Linksys RV042 Bedienungsanleitung

Linksys

Linksys WET54G - Wireless-G EN Bridge Bedienungsanleitung

Linksys

Linksys RV042 Bedienungsanleitung

Linksys

Linksys LRT224 Bedienungsanleitung

Linksys

Linksys RV016 Bedienungsanleitung

Linksys

Linksys EA6350 Bedienungsanleitung

Linksys

Linksys QuickVPN - PC Bedienungsanleitung

Linksys

Linksys FGW5500 Bedienungsanleitung

Linksys

Linksys BEFVP41 - EtherFast Cable/DSL VPN Router Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise