Linksys WAP2000 Bedienungsanleitung

USER GUIDE

BUSINESS SERIES

Wireless-G

Access Point with

Power Over Ethernet

Model: WAP2000

About This Guide

Wireless-G Access Point with Power Over Ethernet

About This Guide

Icon Descriptions

While reading through the User Guide you may encounter

various icons designed to call attention to a specific item.

Below is a description of these icons:

NOTE: This check mark indicates that there is

a note of interest and is something that you

should pay special attention to while using the

product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is

something that could damage your property or

product.

WEB: This globe icon indicates a noteworthy

website address or e-mail address.

Online Resources

Website addresses in this document are listed without

http:// in front of the address because most current web

browsers do not require it. If you use an older web browser,

you may have to add http:// in front of the web address.

Resource Website

Linksys www.linksys.com

Linksys International www.linksys.com/international

Glossary www.linksys.com/glossary

Network Security www.linksys.com/security

Specifications are subject to change without notice.

Linksys is a registered trademark or trademark of Cisco

Systems, Inc. and/or its affiliates in the U.S. and certain

rights reserved. Other brands and product names are

trademarks or registered trademarks of their respective

holders.

Open Source

This product may contain material licensed to you under

the GNU General Public License or other open-source

software licenses. Upon request, open-source software

source code is available at cost from Linksys for at least

three years from the product purchase date.

WEB: For detailed license terms and additional

information visit: www.linksys.com/gpl

Table of Contents

Wireless-G Access Point with Power Over Ethernet

Chapter 1: Introduction 1

Chapter 2: Planning Your Wireless Network 2

Network Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Roaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Network Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Example of a Simple Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 3: Product Overview 3

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Side Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 4: Installation 4

Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Wall-Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connecting the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 5: Advanced Conguration 6

Accessing the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup > Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup > Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Wireless > Wireless Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wireless > VLAN & QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

AP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Administration > Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Administration > Factory Default. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Administration > Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Administration > Conﬁguration Management . . . . . . . . . . . . . . . . . . . . . . . .17

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Status > Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Status > System Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Appendix A: Troubleshooting 20

Appendix B: Wireless Security Checklist 23

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Table of Contents

Wireless-G Access Point with Power Over Ethernet

Appendix C: Glossary 24

Appendix D: Specications 28

Appendix E: Warranty Information 29

Appendix F: Regulatory Information 30

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Industry Canada Radiation Exposure Statement: . . . . . . . . . . . . . . . . . . . . . . .30

Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Avis d’Industrie Canada concernant l’exposition aux radiofréquences :. . . . . . . . .31

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Avis de non-responsabilité concernant les appareils sans ﬁl . . . . . . . . . . . . . . . . . .31

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Appendix G: Contact Information 36

Introduction

Wireless-G Access Point with Power Over Ethernet

Chapter 1

Chapter 1:

Introduction

Thank you for choosing the Wireless-G Access Point with

Power Over Ethernet.

The Wireless-G Access Point with Power Over Ethernet

is ideal for small businesses that want to expand their

existing wired networks or create new wireless networks

for the workforce or guests. The Access Point features

RangeBooster technology that is compatible with

standard 802.11g but with a range up to two times further

and throughput up to 35% faster. Unlike ordinary wireless

technologies that are hampered by wireless signals that

reflect off walls, ceilings, and other objects, RangeBooster

usesthesemultiple signalswith twosmartreceiversateach

end (router or access point and client adapter) to boost

range and throughput speeds. As a result, a RangeBooster

solution reduces or eliminates wireless signal dead spots

in offices and other buildings so users can connect to the

network in more areas. The Access Point comes with two 3

dBi antennas for increased power, also helping to extend

the range of the Access Point.

Advanced security features like Wi-Fi Protected Access™

(WPA2 Enterprise), make this solution ideal for business.

Integrated Quality of Service (QoS) features provide

consistent voice and video quality on both the wired

and wireless networks, enabling your workforce to

communicate or view video content without disruptions

and delay.

The Wireless-G Access Point with Power Over Ethernet can

be powered from its included AC adapter or from a Power

over Ethernet (PoE) Switch via Ethernet cabling, enabling

mounting in ceilings or high on walls where power outlets

may not be available.

Additional features like Multiple BSSIDs,Wireless Roaming,

Auto-Channel Selection, and Load Balancing give your

business added flexibility to keep employees and guests

connected. The Access Point also features dual firmware

images so it remains functional if a firmware upgrade

process is disrupted.

The Wireless-G Access Point with Power Over Ethernet is

Linksys One Ready. That means it includes the necessary

firmware for seamless integration into a Linksys One data

or data/voice network. Once connected, a Linksys One

Service Router will discover the Access Point, automatically

configure it and make it available to other users on the

network. Linksys One technology is automatic and self-

configuring.

Planning Your Wireless Network

Wireless-G Access Point with Power Over Ethernet

Chapter 2

Chapter 2:

Planning Your Wireless

Network

Network Topology

A wireless network is a group of computers, each equipped

with one or more wireless adapters. Computers in a

wireless network must be configured to share the same

radio channel to talk to each other. Several PCs equipped

with wireless cards or adapters can communicate with

each other to form an ad-hoc network without the use of

an access point.

Linksys wireless adapters also provide access to a wired

network when using an access point or wireless router.

An integrated wireless and wired network is called an

infrastructurenetwork.EachwirelessPCinaninfrastructure

network can talk to any computer in a wired or wireless

network via the access point or wireless router.

An infrastructure configuration extends the accessibility

of a wireless PC to a wired network, and may double the

effective wireless transmission range for two wireless

adapter PCs. Since an access point is able to forward data

within a network, the effective transmission range in an

infrastructure network may be doubled (depending on

antenna characteristics).

Roaming

Infrastructure mode also supports roaming capabilities

for mobile users. Roaming means that you can move your

wireless PC within your network and the access points will

pick up the wireless PC’s signal, providing that they both

share the same wireless security and SSID.

Before you consider roaming, choose a feasible radio

channel and optimum access point position. Proper access

point positioning combined with a clear radio signal will

greatly enhance performance.

NOTE: Spanning Tree Protocol should be

disabled on the switches connecting to the APs

to allow roaming to work without disruption.

Network Layout

The Access Point has been designed for use with 802.11g

and 802.11b products, such as the Notebook Adapters for

your laptop computers, PCI Adapters for your desktop PCs,

and USB Adapters for either a laptop or desktop. These

wireless products can also communicate with a 802.11g

or 802.11b Wireless Print Server.

To link your wired network with your wireless network,

connect the Access Point’s Ethernet network port to any

switch or router.

Example of a Simple Wireless Network

Internet

Broadband

Modem

Switch or

Router Wired Clients

WAP2000

Wireless Access Point

Wireless Clients

Example of Simple Wireless Network

The above diagram shows a typical infrastructure wireless

network setup. The Wireless Access Point connects to a

Linksys switch that provides power to the Access Point.

The Access Point can connect multiple wireless devices

to the network. This network will provide connectivity

among wireless network devices and PCs that have a wired

connection to the switch. The switch then can connect to

a router that can connect to an ISP for Internet access.

Product Overview

Wireless-G Access Point with Power Over Ethernet

Chapter 3

Chapter 3:

Product Overview

Front Panel

The front panel is where the Access Point’s LEDs are

located. The LEDs display information about network

activity and connectivity.

Front Panel

Power (Green) The Power LED lights up when

the Access Point is powered on.

PoE (Green) The PoE LED lights up when the

Access Point is powered through Ethernet

cable.

Wireless (Green) The Wireless LED lights up

when the wireless module is active on the

Access Point. If the Wireless LED is flashing, the

Access Point is actively sending or receiving

data from a wireless device.

Ethernet (Green) The Ethernet LED lights up

when the Access Point is successfully connected

to a device through the Ethernet network port.

If the Ethernet LED is flashing, the Access Point

is actively sending to or receiving data from one

of the devices over the Ethernet network port.

Back Panel

The back panel is where the power, Ethernet, and antennas

are connected to the Access Point.

Back Panel

Antenna Ports The Access Point has two

antenna ports for connecting detachable 3

dBi omnidirectional antennas. Adjust the two

antennas so that they form a 90 degree angle

for best MIMO range performance.

Reset There are two ways to reset the Access

Point’s factory defaults. Either press the Reset

button for more than ten seconds, or restore

the defaults using the Access Point’s web-based

utility. If you press the reset button for less

than ten seconds, the Access Point will simply

reboot.

If you power on the Access Point while holding

down the reset button, the Access Point will

be configured with a default static IP address

of 192.168.1.245, see “Chapter 5: Advanced

Configuration” for details.

IMPORTANT: Resetting the Access Point will

erase all of your settings (including wireless,

security, and IP configuration) and replace them

withthefactorydefaults. Donot resetthe Access

Point if you want to retain these settings.

Ethernet The Ethernet network port connects

to Ethernet network devices, such as a switch or

router. The Access Point can be powered using

Power over Ethernet.

Power ThePowerportconnects tothesupplied

power adapter. Use this option if your switch or

router doesn’t support Power over Ethernet.

Side Panels

Security slots are located on both side panels of the Access

Point.

Side Panel

Security Slots The security slots can be utilized

to attach a lock to the Access Point.

Installation

Wireless-G Access Point with Power Over Ethernet

Chapter 4

Chapter 4:

Installation

Placement

The Access Point can be placed horizontally on a flat

surface such as a desktop so it sits on its four rubber feet

or it can be mounted on a wall.

Desktop Placement

Wall-Mount

The unit has two sets of wall-mount slots so that it can be

mounted either vertically or horizontally.

You will need 2 suitable screws to mount the Access

Point.

Suggested Mounting Hardware

2.5-3 mm

4-5 mm 1-2 mm

NOTE: Linksys is not responsible for damages

incurred by insecure wall-mounting hardware.

Determine where you want to mount the Access Point.

Ensure that the wall you use is smooth, flat, dry and

sturdy and make sure the location is within reach of

the power outlet.

Drill two holes into the wall for either vertical or

horizontal placement.

NOTE: The printed Quick Installation Guide

that accompanies the Access Point includes

templates that can be used for spacing

between holes.

Horizontal Mounting

NOTE: The Access Point should be oriented as

shown above for horizontal mounting.

Vertical Mounting

NOTE: The Access Point should be oriented as

shown above for vertical mounting.

Insert a screw into each hole, and leave 3 mm of its

head exposed.

Maneuver the Access Point so the wall-mount slots

line up with the two screws.

Place the wall-mount slots over the screws and slide

the Access Point down until the screws fit snugly into

the wall-mount slots.

Installation

Wireless-G Access Point with Power Over Ethernet

Chapter 4

Connecting the Access Point

Connect the antennas to the antenna connectors on

the Access Point.

Connect the Antennas

Adjust the two antennas so that they form a 90 degree

angle for best performance.

Adjust the Antennas

Connect your Ethernet network cable to your network

router or switch.

LINK/ACT PoE LINK/ACT PoE LINK/ACT Gigabit LINK/ACT Gigabit

Connect the Ethernet cable to the Router or Switch

Connect the other end of the network cable to the

Access Point’s Ethernet port.

Connect the Ethernet cable to the Access Point

NOTE: If your router or switch provides Power

over Ethernet, then step 5 is not necessary.

If you are not using PoE (Power over Ethernet), then

connect the included power adapter to the Access

Point’s Power port. Then plug the power adapter into

an electrical outlet. The LEDs on the front panel will

light up as soon as the Access Point powers on.

Connect the Power

Installation is complete. For advanced configuration

information, proceed to the next chapter.

Chapter 5 Advanced Configuration

Wireless-G Access Point with Power Over Ethernet

Chapter 5:

Advanced Configuration

The Access Point has DHCP enabled by default and should

receive an IP address automatically from the DHCP server

on your network.

If your network doesn’t have a DHCP server, a static IP

address (192.168.1.245) can be assigned to the Access

Point by performing the following steps:

Disconnect the power to the unit.

Using a straightened paper clip or similar object to

hold down the reset button on the back panel of the

Access Point.

Keep the reset button held down and reconnect the

power to the unit. The reset button should be held

until the WLAN LED lights up.

Accessing the Web-Based Utility

Open your web browser and enter the IP address of

your Access Point into the Address field and press the

Enter key. The Password screen will appear.

Address Field

The first time you open the web-based utility, enter

admin (the default user name) in the User name field

and enter it again in the Password field. Click the OK

button. You can change the Access Point’s password

later from the Administration > Management screen.

Web-Based Utility

The first screen that appears is the Setup screen. This

allows you to change the Access Point’s general settings.

There are options on the left side of the screen: Setup,

Wireless, AP Mode, Administration, and Status. Each

option contains screens that will help you configure and

manage the Access Point.

Setup > Setup

This screen is used to enter names for the Access Point and

configure the IP settings.

Setup > Basic Setup

Host Name This is the host name assigned to the Access

Point. This host name will be published to your DNS server

if the Access Point is configured to acquire the IP address

through DHCP. In that case, Linksys recommends to follow

the company policy on the host name assignment. The

default name is Linksys.

Device Name You may assign any device name to

the Access Point. This name is only used by the Access

Point administrator for identification purposes. Unique,

memorable names are helpful, especially if you are

employing multiple access points on the same network.

Contact Use this field to specify the contact string for

your SNMP agent.

Location Use this field to specify the location string for

your SNMP agent.

Automatic Configuration - DHCP Selected by default,

this option is used if you have a DHCP server enabled on

the LAN and want it to assign an IP address to the Access

Point.

Static IP Address This option is used to assign a static or

fixed IP address to the Access Point.

Andere Handbücher für WAP2000

Inhaltsverzeichnis

Andere Linksys Drahtloser Zugangspunkt Handbücher

Linksys

Linksys LAPAC1750PRO Bedienungsanleitung

Linksys

Linksys WAP54G - Wireless-G Access Point Bedienungsanleitung

Linksys

Linksys WAP4410N Bedienungsanleitung

Linksys

Linksys WAP4400N Bedienungsanleitung

Linksys

Linksys LAPAC1750 Bedienungsanleitung

Linksys

Linksys Instant Wireless Series WAP54G Bedienungsanleitung

Linksys

Linksys LAPN300 Bedienungsanleitung

Linksys

Linksys WAP54GPE - Wireless-G Exterior Access Point Bedienungsanleitung

Linksys

Linksys WAP2000 Original Betriebsanleitung

Linksys

Linksys WAP54G - Wireless-G Access Point Original Betriebsanleitung

Linksys

Linksys WPG54G Original Betriebsanleitung

Linksys

Linksys WAP54A - Instant Wireless - Access Point Bedienungsanleitung

Linksys

Linksys WAP54GPE - Wireless-G Exterior Access Point Bedienungsanleitung

Linksys

Linksys WRT610N V1 Bedienungsanleitung

Linksys

Linksys EtherFast Instant Broadband BEFW11S4 Bedienungsanleitung

Linksys

Linksys EtherFast Instant Broadband BEFW11S4 Bedienungsanleitung

Linksys

Linksys WAP200E Bedienungsanleitung

Linksys

Linksys WAP54A - Instant Wireless - Access Point Bedienungsanleitung

Linksys

Linksys WAP300N Bedienungsanleitung

Linksys

Linksys WAP11 - Instant Wireless Network Access... Bedienungsanleitung

Linksys

Linksys WAP11 - Instant Wireless Network Access... Bedienungsanleitung

Linksys

Linksys WAP54G - Wireless-G Access Point Original Betriebsanleitung

Linksys

Linksys WAP54G v2 Bedienungsanleitung

Linksys

Linksys WAP200 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung