Liquid Force TENSION Bedienungsanleitung

TENSION 4-Line Kite Manual

Warnings and safety precautions

Read the following points before assembling your kite

Contents

02 Safety Check List

04 Package List

05 Kite Assembly

08 Wind Reference Guide

09 Setup and Storage

10 Repair

11 Warranty Policy

WARNINGS AND

SAFETY CHECK LIST

Warning:

1)Kite flying can be dangerous.

2)Always use extreme caution when using this product.

3)Misuse of this product can cause serious injury or death.

4)Only use this product if you are in good physical health.

5)Never act in a careless manner when using this product (such as

jumping in the air or tying yourself to as tree to get airborne).

6)You are responsible for your own safety and the safety of others

around you when using this product.

Use Caution with Flying Lines

1)Never touch the flying lines when the kite is in use. Flying lines

are extremely sharp while under tension and can cause serious

injury or death.

2)Never use this product with worn lines. A line that breaks while

under tension can cause serious injury or death.

3)Always check your flying lines for knots before each use. Knots

greatly reduce the strength of the lines.

4)Stay away from tangled flying lines unless the kite is secured to

the ground. An unsecured kite can self launch unexpectedly, and

cause serious injury or death.

5)Never allow yourself, or anyone else, to get between the control

bar and the kite when using this product.

Choose Safe Weather Conditions

1)Never learn to use this product in more than 10 knots of wind.

2)Never use this product in high winds.

3)Never use this product in thunder and lightning conditions.

4)Only use this product when you can remain in a standing position.

5)Never use this product in wind conditions that are above your

ability level.

6)Never use this product near water or in offshore wind conditions

unless you are an expert swimmer.

Choose a Safe Location

1)Always observe local rules and regulations before using this

product.

2)Never use this product near power lines, telephone poles, trees,

bushes, roads, automobiles, or airports. Liquid Force Tension User Guide 02

3)Only use this product when you have 100 meters of clear space

downwind, and on both sides of your launching position. The

power of the kite can pull you downwind unexpectedly and with

great force.

4)Do not fly your kite over other people or pets. Spectators should

always remain behind you when using this product.

5)Never use this product on crowded beaches or fields.

6)Never use this product near the water unless you know how to

swim and are in good physical health.

7)Always practice launching and landing procedures and

self-rescue techniques before using this product near the water.

Important Safety Rules

1)This product is not a personal flotation device. Always wear a

coast guard approved personal flotation device when using this

product near the water.

2)Always have a partner when launching and landing your kite.

3)Always learn to use a small sized, two line stunt kite (one meter

or smaller) before attempting to use this product for the first time.

4)Never allow anyone who is not familiar with traction kiting to use

this product without experienced assistance.

5)Never use this system without a wrist leash system. An

unsecured kite is extremely dangerous to everyone downwind of

you.

6)The wrist leash system is not a permanent attachment to this

product. Never permanently attach yourself to the kite or any of

its components.

7)Always wear a helmet, gloves, shoes, and protective eyewear

when using this product.

Release of Liability, Claim Waiver and

Assumption of Risk Agreement

By inflating the leading edge and assembling this product, you are

agreeing to:

1) Be bound to the terms set forth below and

2) Require anyone using this product to be bound by such terms. If

you are unwilling to be bound by these terms, return this product

(before use) for a full refund.

Assumption of risk

Use of this product and any of its components involves

certain inherent risks, dangers, and hazards, which can result in

serious personal injury or death. In using this product you may

freely agree to assume and accept all known and unknown risks of

injury while using this equipment. The risks inherent in this sport

can be greatly reduced by abiding by the warning guidelines listed

in the users guide and by using common sense.

Release of waiver and claims agreement

In consideration of the sale of this product to you, hereby

agree to the fullest extent permitted by law as follows:

To waive any and all claims That you have or may in the

future have against liquid force kiteboards, or any of its agents,

resulting from use of this product and any of its components.

To release Liquid Force Kiteboards, or any of its agents, from

any and all liability for any loss, damage, injury, or expense that you

or any users of this product may suffer, as a result of the use of this

product, due to any cause whatsoever, including negligence or

breach of contract on the part of liquid force kiteboards, or any of its

agents, in the design or manufacture of this product.

Liquid Force Tension User Guide 03

Centerline Leash

Powerstrap

Spreader Bar

Trimmer Loop Leash

attachment

buckle

Red Black

Harness line

Carbon Bar

Powerline

attachment

points

Powerline

attachment

points

Forward Centerline Attachment Point

-Fast turning

-Increased sheetability

-Increased windrange

-Increased response

Back Centerline Attachment Point

-Needs less bar pressure to turn

-Kite is less sensitive to bar position

-More Power goes to the spreader bar

Forward Attachment Point

-For high winds

-Kite is less responsive to bar movement,

creating more stable kite in the air

-Position for beginners or rider wanting less sensitive kite

-Great for wake style tricks

Rear Attachment Point

-Can ride using smaller bar

-More forgiving

-Fastest turning

-Preferred for wave ridding

-Less hand pressure to turn

-Greatest sheetability

-Greatest low end power

-Underpowered conditions

Liquid Force Tension User Guide 04

The Complete Four-Line Package Includes:

- 100% Carbon Control Bar

- Custom Aspect Ratio Kite Body

- Adjustable Center power strap

- De-powering Loop

- 4 Line Reduced diameter control bar with molded winders

- 1 Set 4 Line 27m Color Coded Flying Lines

- Extension Line Set With Center Line release system

- 24” Harness Line

- Large Dual Direction Kite Pump

Step 1: Inflating The Struts

1)Unroll the kite with the leading edge strut facing the direction of

the wind. The kite should be lying upside down with the body

struts facing upwards so the can be inflated(fig. 1.1)

2)It is important to hold the leading edge of kite on ground on the

windward side. You can secure the leading edge by using

sand or your foot.

3)Inflate the body struts first, then inflate the leading edge.

4)To inflate the bladder, insert the hand pump all the way into the air

valve(Fig 1.2)

5)Hold the base of the air valve with the valve cap and one end of

the velcro closure between your third and little finger(fig 1.2)

6)Pump air into the bladder until firm

7)Do not over inflate. You need just enough air to keep body struts

and leading edge under load. Over inflating can cause damage to

the bladder.

8)Do not under inflate. The kite will not self-launch if you do not

have enough air in the leading edge.

9)Pinch the valve around the base, remove the pump and insert the

cap into the air valve. Secure the Velcro closure over the valve

cap (Fig 1.3)

10)DO NOT try to push the air valve into the bladder like you would

on a beach ball. This will cause damage to the valves and

bladders.

11)Once inflated, secure your kite by laying the leading edge o the

ground facing the direction of the wind. Put sand or a heavy object

on the windward side of the kite so it will not blow away.

Step 2: Rigging your four line kite

Before You Start: When rigging your kite, make sure the front lines

are 5 inches longer than the back lines. This measurement should

be checked when the lines are stretched out all the way on the

ground, and center power adjustment strap is extended all the way.

(Diagram of rigging shown below)

Warning:

Never use a Liquid Force kite without a wrist leash system. A

loose kite is extremely dangerous for anyone downwind of you.

Fig 1.2

Fig 1.1 Fig 1.3

Centerline Leash

Powerstrap

Spreader Bar

Trimmer Loop Leash

attachment

buckle

Red Black

Harness line

Carbon Bar

Powerline

attachment

points

Powerline

attachment

points

Liquid Force Tension User Guide 05

Step 3: Lay Out the Flying Lines (This technique will ensure that

your lines are separated and free of knots.)

1)Unroll approximately 3 to 6 feet of line from the bar.

2)Hold all 4 lines in one hand and secure them with a knot to a

stationary object such as the binding of your board. (Fig. 1.4)

3)When lines are secure, hold on to your bar and walk away from

the board until the lines are completely extended.

4)At the point where your lines are fully extended, bury the bar in the

sand with the red side on your left and the black side on your right,

facing the board. (Fig. 1.5)

5)Pick up the outside lines with both hands (one line in each hand),

and step on the inside lines with each foot.

6)While holding the outside lines apart, and stepping on the inside

lines, walk toward your board.

7)Separate the lines as you go and ease out any knots. (Fig. 1.6)

8)When you reach the board, untie the lines from the binding and lay

the tips out in the following order: green and black, all green, all

red, red and black. (picture 1.7 )

Step 4: Attach The Flying Lines

1)Lay your kite upside down with the leading edge facing the

direction of the wind. (Fig 1.8)

2)Secure the kite by folding the tip over the strut and covering it with

sand. Use enough sand to hold it down in gusty conditions.

(Fig. 1.9)

3)Next, connect the flying lines to the kite as stated below.

-Red to Red

-Yellow to Yellow

-Black to Black

4)IMPORTANT: Double check that no lines are crossed before

launching your kite.(Fig 1.10 and 1.11)

Fig 1.4 Fig 1.5

Fig 1.6 Fig 1.7

Fig 1.8 Fig 1.9

Fig 1.10 Fig 1.11

Liquid Force Tension User Guide 06

Step 5: Attach The Wrist Release System To Your Arm

1)The wrist release system is used in the event you are forced to let

go of the control bar to avoid danger. Upon letting go of the

control bar, the wrist release system will take hold and allow

enough slack in the flying lines that the kite will de-power itself and

fall to the ground. (Fig. 1.12)

Warning:

Letting go of the control bar in high wind conditions can cause the

wrist leash system to release from your arm. Never go further out

than you can comfortably swim back to shore. Know your

limitations and never kite in conditions beyond

your ability.

Points To Remember When Assembling Your Kite

1)Always examine the flying area for the safest

position to launch and land the kite.

2)Never leave your kite unattended while the struts are inflated. An

unattended kite can self-launch unexpectedly with great force.

3)Always check your lines for wear and tear before each flight.

Lines typically begin to show signs of wear and tear at the junction

points.

4)Do not assemble or launch your kites around sharp objects such

as, trees, bushes, and driftwood. This can cause damage to your

kite and puncture the bladders.

5)Do not over inflate the body struts. This can cause damage to the

seams of the internal bladders.

6)Do not push the air valves into the bladders like you would on a

beach ball. This will cause damage to the valve and the bladder.

7)Keep the hand pump, air valves, and the inside of the bladders

clean. Avoid contact with sand, dirt, and salt water because it can

cause damage to these items.

8)Never clean your kite with water when the air valves are open.

9)Never roll your kite up wet

Using The Center Line Adjuster

1)The 4 line kite comes with a center line power strap which will

allow you to fine tune the power of your kite while flying.

2)By pulling the black webbing toward you, the length of the front

lines are shortened reducing the power of the kite. (Fig 1.13)

3)By pulling down on the red webbing you will increase the power of

the kite by lengthening the front lines. (Fig 1.14)

4)By adjusting the length of the front lines, you will find the power

that best suits the conditions. This system, in conjunction with the

center de-powering loop system, will greatly increase the range of

your kite.

Using the Center Loop

1)The 4-line kite also features a unique center loop adjustment

system, which allows you to adjust the power of the kite with your

harness (shown on diagram)

2)To use the center loop while flying the kite, unhook from your main

harness line and pull the bar toward you. (show picture 1.15)

3)Hook into the center loop (show picture 1.16)

4)By pulling and releasing the center loop with your harness, you will be

able to increase and decrease the power of your kite. Pull in on the

center loop with your harness to de-power the kite. Use this technique

when launching and flying in gusty conditions. (Fig. 1.17)

Fig 1.12

Fig 1.13 Fig 1.14

Fig 1.15 Fig 1.16 Fig 1.17

Liquid Force Tension User Guide 07

(Center Loop diagram shown below) Understanding the wind

(look at diagrams here)

min. 100m

min. 100m30m

wind

DANGER ZONE

AVOID THIS AREA

FLYING ZONE

ZONE BETWEEN KITE AND PILOT

STAY OUT OF THIS AREA

PARTNER

ON-SHORE WINDS

OFF-SHORE WINDS

SIDE-SHORE WINDS

LAND

WATER

WIND DIRECTION

UPWIND

REACH

DOWNWIND

UPWIND

REACH

DOWNWIND

Liquid Force Tension User Guide 08

Kite size reference guide

This table is only to be used as a rough guideline when choos-

ing the correct kite for your weight. Other factors may affect your deci-

sion such as your ability level, the consistency of the wind, and the

size and volume of the board you are planning to use. It is also rec-

ommended that you chose a smaller size than is listed here if you are

planning to fly your kite in gusty conditions. This table is based on a

175 lb/80 kg person. . those who are significantly lighter in weight

should choose a kite that is one size smaller for the wind conditions,

those heavier should choose one size larger.

Setup and Storage Tips

Harness Line Setup

1)The harness line must be setup as shown to avoid unnecessary

strain on the control bar.

2)Harness lines placed too closely together will exert excessive

pressure on the control bar and may cause it to bend or break.

Carrying an Inflated Kite

1)To carry an inflated kite upwind safely, take the control bar in one

hand, grasp the kite (with the same hands) on the leading edge at

the center strut. This will allow you to control the kite while walking

upwind. ATTENTION:

Allow kite to dry before storage. Colors will bleed if kite is stored

when wet or damp.

Control Bar Winding Instructions

To avoid tangled lines, follow the instructions below before storing your

kite. (make sure to show a picture for each instruction)

1)Lay out lines in a strait line on ground and grasp control bar at

center.

2) Grasp extension lines and center lines together with the other hand.

3)Wrap lines over winder at one end of bar and back to the other

winder following a figure eight pattern.

4)Continue wrapping lines. Pull lines in taught in order to keep

pressure on the wrap.

5)Wrap until a few feet of flying lines remain, then wrap lines 90

degrees to the bar four times securing the ends.

RIGHT WRONG

1) 2)

Liquid Force Tension User Guide 09

Repair

1)Lay the kite out flat with struts facing up.

2)Make sure the flying lines are removed and all the struts are

deflated.

3)Open the strut tip by detaching the Velcro strip and pushing it

through the securing loop with your index finger

Important:

Before removing the bladder, tie a feed line (about 10 feet long) to

the end of the bladder. You will later use the feed line to re-insert

the bladder.

4)Push the air valve into the strut so it is completely clear from the

valve opening. Find the strut opening. It is located near the

center of the leading edge.

5)When you are ready to start pulling the bladder out of the strut

opening, have a partner hold the strut tip to keep tension and

make sure the feed line goes in properly.

6)Once the bladder is completely out, the feed line fully inserted into

the strut with excess line line hanging out of the tip.

7)Inflate the bladder and submerge it in a bucket of water. Look for

air bubbles to find any wholes in the bladder. This method is

similar to repairing a bicycle innertube tire.

8)Dry and clean the bladder with a towel, and mark the hole using

a black felt pen. Again deflate the bladder.

9)Using the sandpaper enclosed in the repair kit, lightly rough the

area to be repaired.

10)Peel the backing off the repair patch and press it on the bladder

to cover the hole.

Important:

Make sure the bladder is dry and the air valve is closed before

proceeding further. Put the bladder in plastic bag with a sufficient

amount of talcom powder.

11)Close the bag and shake it until the the talcom powder

completely covers the bladder. Before you begin the restoration

process, fold the bladder ike an accordion wit the air valve lined

up to the valve opening.

12)Have your partner pull the feed line so the bladder is reinserted

into the strut. While doing this, you should keep tension on the

strut and make sure the bladder is inserted properly.

Important:

Once the bladder is completely inserted into the strut, make sure

the air valve is properly exposed through the valve opening.

13)Inflate the bladder until it is half-full of air. Check to make sure

that the bladder is inserted correctly and that there are no folds in

Liquid Force Tension User Guide 10

Andere Liquid Force Flugzeug Handbücher

Liquid Force

Liquid Force NV Series Bedienungsanleitung

Beliebte Flugzeug Handbücher anderer Marken

Cessna

Cessna U206G STATIONAIR Betriebsanleitung

Cirrus

Cirrus SR22 Bedienungsanleitung

Schleicher

Schleicher ASK 21 Montageanleitung

Aircraft

Aircraft REIMS F152 Technische Daten

Skywalk

Skywalk Tequila 2 Bedienungsanleitung

MAULE

MAULE M-7-235B Technische Daten

Ozone

Ozone Indy Handbuch

Tecnam

Tecnam P92 Echo Super Bedienungsanleitung

Wills Wing

Wills Wing HP II Bedienungsanleitung

Ozone

Ozone Roadster Handbuch

Cirrus

Cirrus SR20 Bedienungsanleitung

Niviuk

Niviuk KOYOT 3 Bedienungsanleitung

Pipistrel

Pipistrel ALPHA Trainer Bedienungsanleitung

REVELL

REVELL SnapTite BLUE ANGELS F-18 HORNET Bedienungsanleitung

Cessna

Cessna 172 Series 1973 Bedienungsanleitung

Sky

Sky EOLE Bedienungsanleitung

Sabfoil

Sabfoil Surf Foil Bedienungsanleitung

Cessna

Cessna 182S Skylane Kurzanleitung zur Einrichtung