Litecraft ILED-MP-07F5-010 Bedienungsanleitung
LED Multipar 7FC
ILED-MP-07F5-010
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
USER GUIDE
1A
CONTENTS
1. Safety Instructions........................................................................................ 2
2. Technical Specifications................................................................................ 4
3. How to Set the Fixture ................................................................................. 5
3.1 Control Panel.......................................................................................... 5
3.2 Main Function ........................................................................................ 6
4. How to Control the Unit .............................................................................11
4.1 Master/Slave Built In Preprogrammed Function......................................11
4.2. Easy Controller (by CA-8) .....................................................................12
4.3 DMX Controller .....................................................................................12
5. DMX 512 Configurations.............................................................................14
6. DMX 512 Connections................................................................................15
7. Troubleshooting ..........................................................................................16
8. Fixture Cleaning ..........................................................................................17
2A
1. Safety Instructions
WARNING
yPlease keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
yPlease unpack and check carefully there is no transportation damage before using the unit.
yBefore operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
yIt’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
yThe unit is for indoor use only. Use only in a dry location.
yThe unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
yPlease disconnect main power before replacement or servicing.
yPlease make sure there are no flammable materials close to the unit while operating as it is
fire hazard.
yPlease use safety cable when fixes this unit. DO NOT handle the unit by taking its head only,
but always by taking its base.
yMaximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is
higher than this.
yUnit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to cool
down before replacing or serving.
Please read the instruction carefully, it includes important
information about the installation, usage and maintenance.
3A
yIn the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center. Always use
the same type spare parts.
yDO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:
yTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
yDO NOT open the unit within five minutes after switching off.
yThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact your
nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. And make sure that the
structure to which you are attaching the unit is secure and is able to support a weight of 10
times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.
For 230V 50Hz power supply, maximum fixtures that can be connected on one power cable is 8;
For 120V 60Hz power supply, maximum fixtures that can be connected on one power cable is 4;
4A
2. Technical Specifications
◇Equipped with 7pcs of 10W Quad color LEDs, creating extra ordinary color mixing and
powerful beam and wash effect
◇DMX Channels: 4/5/7 channels selectable
◇Beam Angle: 10°
◇0-100% full range dimmer and variable strobe speed
◇Optional easy controller CA-8 for instant lighting show
◇High efficiency, low power consumption
◇Super compact, low weight
Voltage: AC 100V~240V, 50/60Hz
Power Consumption: 78W
Fuse: T6.3A
LED: 7×10W Quad-color LED
Dimension: 260 × 195 × 293mm
Weight: 3.9Kgs
5A
3. How to Set the Fixture
3.1 Control Panel
1. Mains Output: Connect to supply mains power for the unit.
2. DMX Output: For DMX512 link, use 3-pin XLR plug cable to link the next unit.
3. Mains Input: Connect to supply mains power for the unit.
4. Microphone: Receive the Sound to control the fixture.
5. Display: Show the various menus and the selected functions
LED:
6. DMX On DMX input present
7. MASTER On Master Mode
8. SLAVE On Slave Mode
9. SOUND Flashing Sound activation
10. DMX Output: For DMX512 link, use 3-pin XLR plug cable to output the DMX single.
6A
Button:
11. MENU To select the programming functions
12. DOWN To go backward in the selected functions
13. UP To go forward in the selected functions
14. ENTER To confirm the selected functions
15. Only for remote control: Connect with CA-8 to control the unit for Stand by, Function and
Mode function.
3.2 Main Function
To select any functions, press the MENU button until the required one is shown on the
display. Select the function by the ENTER button and the display will blink. Use the DOWN
and UP button to change the mode. Once the required mode has been selected, press the
ENTER button to setup or it will automatically return to the main functions without any
change after idling one minute. Back to the functions without any change press the MENU
button.
The main functions are shown below:
7A
8A
DMX 512 Address
Select the , press the ENTER button and the display will blink. Use the DOWN and UP
button to change the DMX 512 address. Once the address has been selected, press the
ENTER button to setup or automatically exit menu mode without any change after one minute.
Back to the previous functions without any change press the MENU button.
Channel Mode
Select the , press the ENTER button and the display will blink. Use the DOWN and UP
button to select the (4 channels: Red, Green, Blue and White), (5 channels:
Red, Green, Blue, White and Dimmer) or (7 channels: Red, Green, Blue, White, Color,
Dimmer and Strobe) mode. Once the mode has been selected, press the ENTER button to
setup or automatically exit menu mode without any change after one minute. To go back to
the functions without any change press the MENU button.
Slave Mode
Select the , press the ENTER button and the display will blink. Use the DOWN and UP
button to select the (Master), (Slave 1) or (Slave 2) mode. Once the
mode has been selected, press the ENTER button to setup or automatically return to the main
functions without any change after one minute. To go back to the functions without any
change press the MENU button again.
Show Mode
Select the , press the ENTER button and the display will blink. Use the DOWN and UP
button to select the (Random show) or (color) or (fade).
When you selected the , press the ENTER button, and then use the DOWN and UP
button to select the (Color 1) … (Color 9), press the ENTER button and use
the DOWN and UP button to adjust the brightness intensity from (Dimmer 0) to
9A
(Dimmer 255); select the (Color 10), press the ENTER button, and select the
(Red), (Green),… (Dimmer), pressing the ENTER button and adjust the
brightness intensity from to .
When you selected the (Fade mode), press the ENTER button, and then use the
DOWN and UP button to adjust the fade speed from (Speed 1, the slowest) to
(Speed 3: the fastest).
Once you have finished the settings, press the ENTER button to setup or automatically exit
menu mode without any change after one minute. To go back to the last function without any
change press the MENU button.
Sound Mode
Select the , press the ENTER button and the display will blink. Use the DOWN and UP
button to select the (Sound mode on) or (Sound mode off). Once select, press
the ENTER button to setup or automatically exit menu mode without any change after one
minute. To go back to the functions without any change press the MENU button
Sound Sense
Select the , press the ENTER button, use the DOWN and UP button to adjust sensitivity
level between (the lowest) and (most sensitive). Press the ENTER button to
setup or automatically exit menu mode without any change after one minute. To go back to
the functions without any change press the MENU button.
Blackout mode
Select the , press the ENTER button and use the DOWN and UP button to select the
(blackout) or (normal). Press the ENTER button to setup or automatically exit
menu mode without any change after one minute. To go back to the functions without any
change press the MENU button.
Inhaltsverzeichnis
Andere Litecraft Scheinwerfer Handbücher
Beliebte Scheinwerfer Handbücher anderer Marken
VIZULO
VIZULO Micro Martin Benutzerhandbuch
EuroLite
EuroLite LED IP FL-100 SMD Bedienungsanleitung
Cooper Wheelock
Cooper Wheelock XB12 Bedienungsanleitung
Allen + Roth
Allen + Roth 17624-000 Bedienungsanleitung
ADJ
ADJ 4 STAGE PAK Bedienungsanleitung
Cooper Lighting
Cooper Lighting EGL91SW233 Bedienungsanleitung
