LOCKLY GUARD 698L Bedienungsanleitung
LATCH EDITION
INSTALLATION
GUIDE
VISION (698L)
FOR COMMERCIAL USE & PROFESSIONAL INSTALLATION
WWW.LOCKLYPRO.COM
PGD698L
(application in progress)
GET THE MOST OUT OF YOUR
LOCKLY GUARD™
Get the latest user/installation manuals , instructional videos, and FAQs
SCAN or VISIT
Locklypro.com/698L
Reference installation parts overview foldout on back page
Welcome!
This guide will walk you through step-by-step how to install
and get Lockly Guard™up and running. Installation generally
takes less than 30 minutes. If you have any questions please
call our VIP hotline (855) 562-5599 for help.
3
Phillips Screwdriver
To complete the installation you will need:
Flathead Screwdriver Tape measure or ruler
Pliers
Optional
Screwdriver with drill bits
Preparation
Drilling maybe required to install this lock. If you are installing your lock on a
brand new door, a drill is required if there are no holes prepared for lock
installation. Use provided template to bore holes on door.
4
Measure and confirm
your door is between
1-3/8" - 2"
(
35mm -
50mm).
Measure and confirm
the hole in the door is
2-1/8" (54mm)
.
Measure and confirm
that the backset is be
-tween 2 -3/8" (60mm)
to 2 -3/4" (70mm).
Measure and confirm
that hole in the door
edge is 1" (25.4mm).
Remove existing door hardware, latch or deadbolts before installing the
new lock. Use provided template to bore new holes if needed.
1
2
3
4
1- 3/8"—2"
(35mm—50mm)
2-3/8"(60mm)
or
2-3/4"(70mm)
1"
25.4mm
*Optional
IMPORTANT NOTICE
* Use goggles to protect eyes if you need to drill door holes.
4-21/32"(118mm)
2-1/8"
(54mm)
1/2"
(12mm)
Preparation
continued
5
INSTALLING THE LOCKSET
Facing the door exterior, install the lockset according to the in-swing
or out-swing opening direction of your door.
LEFT OUT-SWING DOOR
LEFT IN-SWING DOOR
RIGHT OUT-SWING DOOR
RIGHT IN-SWING DOOR
Inside
Inside
Outside
Outside
Inside
Outside
Inside
Outside
1
2
(a)
Latchbolt Adjustment
Push the shaft (a) to adjust
the lockset to 2-3/8"(60mm)
or 2-3/4"(70mm).
Measure the distance
between center of front
door hole to the edge
of your door. Push the
shaft (a) to adjust the
lockset to 2-3/8"(60mm)
or 2-3/4"(70mm).
Step 1
2-3/4"
(70mm)
2-3/8"
(60mm)
Note: The shaft's horizontal
and vertical aligment must
be sustained
during installa
tion to ensure latch will fully
extend and lock securely.
6
3
INSTALLING THE LOCKSET
Step 1
continued
Install latchbolt Fto door and secure with screws G. Make
sure the spindle shaft is at the center and horizontally positioned.
G
F
7
Changing the Exterior Handle Orientation
12
The lock ships with handle default for right in-swing or left out-swing door.
Check the diagram below if you are unsure of you door orientation.
Hinge
Side
RIGHT IN-SWING DOOR
LEFT OUT-SWING DOOR RIGHT OUT-SWING DOOR
LEFT IN-SWING DOORINTERIOR
EXTERIOR
No need to change door handle
orientation. Skip Step 2.
LEFT-IN SWING and RIGHT OUT-SWING
DOORS require changing the door
handle orientation. Continue to
follow Step 2 to change exterior
and interior door handle orientation.
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
(Right handle)
Insert key and rotate
so
that the two white dots
align as shown.
R
Use the provided pin insert Rto
push the metal pin located at the
3 o’clock of the the base handle,
then the other pin at 9 o’clock
position. Remove the handle once
the pins are compressed.
8
3
Twist key back to horizontal position.
The key can be taken out once it
goes back to the horizontal position.
4
56
Rotate the handle 180° to the other
side
of the lock.
Using your fingers, press the two pins
located on the left and right side of
the the lock to insert the handle back
onto the lock.
Check that your handle works smoothly
by giving it a turn up and down.
Confirm that your installation was
complete by checking if the pins
are flush against the handle, and
has popped out. Adjust the handle
accordingly to make sure the pins
are fully decompressed and sits flush
against the surface.
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
continued
9
Changing the Interior Handle Orientation
1
2
Remove the handle retaining screw
and detach the handle. Rotate
the
handle 180° as shown.
Insert the handle retaining screw
and tighten using a screw driver.
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
Step 2
continued
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere LOCKLY GUARD Türschloss Handbücher
LOCKLY GUARD
LOCKLY GUARD ATHENA 228SL Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD DEFENDER SLIDE EDITION Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728Z Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD DEFENDER 238LM Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD VISION DUO Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728F Z Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD DUO INTERCONNECTED EDITION Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728F ZU Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD VISION DUO Bedienungsanleitung
LOCKLY GUARD
LOCKLY GUARD DEADBOLT 728F Z Bedienungsanleitung
