Lockly SECURE Bedienungsanleitung

SECURE I SECURE PLUS I SECURE PRO

INSTALLATION MANUAL

DEADBOLT EDITION

INSTALLATION OVERVIEW

LocklyTM Secure can be fitted for both right swing doors and left swing doors.

PARTS LIST

D F G J K

P Q A

BH1

x 2

x 8

x 2

Ox 5

x 3

3M Double Sided

Tape- EVA Sticker

STEP 1: PREPARING YOUR DOOR

Make sure your door is prepped for installation prior to installation. Please use

the supplied template for drilling holes required if you choose to drill a hole.

1-3/8"—2"

(35mm—50mm)

1/2"

12mm

3-7/8"(98mm)

25mm

2-3/8"(60mm)

2-3/4"(70mm)

Drill Hole

IMPORTANT NOTICE

You are not required to drill a hole in your door. We have provided 3M

double sided tape for you to help stabilize the lock during installation. Only

drill a hole if you wish to have added stability. Please refer to the provided

templates for drilling if needed.

STEP 2: ADJUSTING THE BOLT

If the latch holes are centered inthe drilled

hole, no adjustment is needed.

If NOT, adjust the latch as shown below.

Push toggle button "A"

downwards andpull part "B"

outwards.

Initial positionof A: 2-3/8"

Pull "C" to 2-3/4" and release

button "a". Now thebackset

has been adjusted to 2-3/4".

31 2

2-3/8"

2-3/4"2-3/4"

Adjust as shown below (as needed)

STEP 3: EXTENDING THE BOLT

Extend the latch bolt as shown. When installing the latch, make sure the

position of the "+" mark is on the bottom

part of the latch.

OP(2X)

MAKE SURE THE BOLT IS FULLY EXTENDED (LOCKED)

BEFORE INSTALLING PROCEEDING TO THE NEXT STEP

STEP 4: PREPARING THE EXTERIOR ASSEMBLY

*The pole (Labeled X) is used if you drilled a hole in your door. It is not required. If you did not drill

a hole in your door, please remove this pole with a flathead screwdriver by turning it counter clock-

wise. You can then apply 3M double sided tape where the pole (Labeled X) used to be. If you

drilled a hole, then make sure the pole (Labled X) is secured tight by tightening clockwise.

When the bolt is extended, the

torqueblade should be kept in

a vertical position.

Install “D” & “C” on “B”

in order as shown.

Vertical

*REMOVE

COUNTERCLOCKWISE

(Pole Removed)

3M TAPE

GOES HERE

STEP 5: INSTALLING THE EXTERIOR ASSEMBLY

Note: Please use rotate the

torque blade into the vertical

position for installation.

B. Make sure the cable goes

underneath the latch.

A. When the bolt is extended,

the torque blade should be kept

in a vertical position.

EXTERIOR VIEW INTERIOR VIEW

Route cable through center hole, then push it into sidehole.

Center Hole

Side Hole

I(2X)

Before screwing check the vertical

alignment for the mounting plate and

exterior assembly.

STEP 5 (CON’TD): INSTALLING THE EXTERIOR ASSEMBLY

After installation, please use the physical key to test the door latch. If the bolt does not

retract or extend smoothly, adjust the screws to ensure the bolt system works smoothly.

* H is only required if you drilled a hole in your door. If you did not drill a hole in your

door, please do not insert H.

Depending on your door thickness, use H1 or H2 screws for the doors.

Doors with thickness of 35-43mm, use H1. Doors with thickness of 43-50mm, use H2.

Connectthe cable.

Please insert the RED face of the cable connector into the

socket marked in RED. Make sure the connector is securely

fixed to the socket.

Torque Blade Thumb turn shaft

Push the thumb turn shaft into the torque blade.

STEP 6: INSTALLING INTERIOR ASSEMBLY

MAKE SURE IT IS IN THE VERTICAL POSITION

Andere Handbücher für SECURE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lockly Sperren Handbücher

Lockly

Lockly LUX Compact Bedienungsanleitung

Lockly

Lockly Vision PGD798SN Bedienungsanleitung

Lockly

Lockly SECURE Bedienungsanleitung

Lockly

Lockly DUO Bedienungsanleitung

Lockly

Lockly VISION ELITE Bedienungsanleitung

Lockly

Lockly SECURE Bedienungsanleitung

Lockly

Lockly DUO Bedienungsanleitung

Lockly

Lockly VISION ELITE Bedienungsanleitung

Lockly

Lockly Vision Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung