Logitech M705 Bedienungsanleitung
Wireless device does not work or is not recognized
When your device isn't working, the problem is likely a connection or power issue. This can be
due to several reasons, such as:
Low battery levels
Plugging the receiver into a USB hub or other unsupported device such as a
KVM switch
NOTE: Your receiver must be plugged directly into your computer.
Using your wireless keyboard on metal surfaces
Radio frequency (RF) interference from other sources, such as wireless speakers, cell
phone, and so on
Windows USB port power settings
If your keyboard is not working or frequently loses connection try the following steps:
1. Check the batteries or make sure your device is charged.
2. Make sure the keyboard is On.
3. Keep other electrical wireless devices away from the USB receiver to avoid interferences.
4. Move the keyboard closer to the USB receiver.
5. Unpair/repair or disconnect/reconnect hardware:
oIf you have a Unifying receiver, identified by this logo, see Unpair a mouse
or keyboard from the Unifying receiver for instructions.
oIf your receiver is non-Unifying, it cannot be unpaired. However, if you have a
replacement receiver, you can use the Connection Utility software to perform the
pairing.
USB receiver does not work or is not recognized
If your device stops responding, confirm that the USB receiver is working properly.
The steps below will help to identify if the issue is related to the USB receiver:
1. Open Device Manager and make sure your product is listed.
2. If the receiver is plugged into a USB hub or extender, try plugging it into a port directly
on the computer
3. Windows only —try a different USB port. If it makes a difference, try updating the
motherboard USB chipset driver.
4. If the receiver is Unifying, identified by this logo, open Unifying Software and
check if the device is found there.
5. If not, follow the steps to connect the device to a Unifying receiver.
6. Try using the receiver on a different computer.
7. If it’s still not working on the second computer, check Device Manager to see if the
device is recognized.
If your product is still not recognized, the fault is most likely related to the USB receiver rather
than the keyboard or mouse.
6. Try a different USB port. If using a different USB port works, try updating the
motherboard USB chipset driver.
7. Windows only —check USB port power settings.
8. Upgrade the firmware for your device if available.
9. Try the device on a different computer.
Keyboard/Mice - Buttons or keys do not work correctly
Likely Cause(s):
Potential hardware issue
Operating system /software settings
USB port issue
Symptom(s):
Single-click results in double-click (mice and pointers)
Repeating or strange characters when typing on the keyboard
Button/key/control gets stuck or responds intermittently
Possible solutions:
1. Clean the button/key with compressed air.
2. Verify the product or receiver is connected directly to the computer and not to a hub,
extender, switch or something similar.
3. Unpair/repair or disconnect/reconnect hardware.
4. Upgrade firmware if available.
5. Windows only —try a different USB port. If it makes a difference, try updating the
motherboard USB chipset driver.
6. Try on a different computer. Windows only —if it works on a different computer, then
the issue might be related to a USB chipset driver.
*Pointing devices only:
If you’re not sure if the problem is a hardware or software issue, try switching the buttons
in the settings (left click becomes right click and right click becomes left click). If the
problem moves to the new button it is a software setting or application issue and
hardware troubleshooting cannot resolve it. If the problem stays with the same button it is
a hardware issue.
If a single-click always double-clicks, check the settings (Windows mouse settings and/or
in Logitech SetPoint/Options/G HUB/Control Center/Gaming Software) to verify if the
button is set to Single Click is Double Click.
NOTE: If buttons or keys respond incorrectly in a particular program, verify if the problem is
specific to the software by testing in other programs.
No optical light visible on the M705 mouse
Your mouse uses an infrared (IR) Laser light that is invisible to the human eye.
If you're not sure if your mouse is turned on, check the ON/OFF switch located on the bottom.
When your mouse is:
ON - The switch is pushed over to the right and you see green next to it.
OFF - The switch is pushed over to the left and you see red next to it.
Mouse isn't working
If your M705 mouse isn't working, the problem is likely a lost connection. The connection
between the mouse and the Unifying receiver can be lost for several reasons, such as:
Low battery levels
Moving the receiver from USB one port to another
Moving the receiver to another computer
Plugging the receiver into a USB hub or other unsupported device such as a KVM switch
(NOTE: Your Unifying receiver must be plugged directly into your computer.)
Using your wireless mouse on metal surfaces
Radio frequency (RF) interference from more powerful devices such as:
oWireless speakers
oComputer power supplies
oMonitors
oCell phones
oGarage door openers
Before reconnecting your mouse
1. Fix or rule out the potential problem sources listed above.
2. Make sure you have fresh batteries in your mouse (see answer 360023222174 for
instructions).
3. Make sure the mouse is turned on (see answer 360023222174 for instructions).
4. Plug the receiver directly and securely into a working USB port on your computer.
5. Turn your computer on.
Reconnecting your mouse
1. Download and install the latest software from the Marathon Mouse M705 Downloads
page.
2. Launch the Logitech Unifying Software:
Windows 7: Start > Programs > Logitech > Unifying > Logitech Unifying Software
Windows 8: Start screen > Logitech Unifying Software
Macintosh: Application > Utilities > Logitech Unifying Software
3. Click Next at the bottom of the Welcome screen.
4. Follow the on-screen instructions to turn your mouse off and then back on.
5. When your mouse is detected, you'll see the confirmation message below. Click Yes and
then Next. Otherwise, repeat from step #4.
6. Click Finish to exit the Logitech Unifying Software. Your mouse should now be
connected.
Mouse or keyboard frequently stops working
Keep other electrical devices at least 8 inches (20 cm) away from the Unifying receiver
Move the mouse or keyboard closer to the Unifying receiver
Move the receiver to a different USB port on your computer
Andere Handbücher für M705
6
Inhaltsverzeichnis
Andere Logitech Maus Handbücher
Logitech
Logitech M54 Bedienungsanleitung
Logitech
Logitech G300s Bedienungsanleitung
Logitech
Logitech 4236041 Bedienungsanleitung
Logitech
Logitech Ultrathin T630 Bedienungsanleitung
Logitech
Logitech 965118-0403 - io 2 Digital Writing System Bedienungsanleitung
Logitech
Logitech NX80 Bedienungsanleitung
Logitech
Logitech M705 Bedienungsanleitung
Logitech
Logitech MX700 Bedienungsanleitung
Logitech
Logitech G304 LIGHTSPEED Installationsanleitung
Logitech
Logitech G402 Hyperion Fury Bedienungsanleitung
Logitech
Logitech M315 Bedienungsanleitung
Logitech
Logitech M280 Bedienungsanleitung
Logitech
Logitech G700 Bedienungsanleitung
Logitech
Logitech M325 Bedienungsanleitung
Logitech
Logitech G502 HERO Bedienungsanleitung
Logitech
Logitech T631 Bedienungsanleitung
Logitech
Logitech LIGHTSPEED G903 SE Bedienungsanleitung
Logitech
Logitech Zone T400 Bedienungsanleitung
Logitech
Logitech WHEEL MOUSE Bedienungsanleitung
Logitech
Logitech 930904-0403 - Optical Mouse For Play Station... Benutzerhandbuch
