London Emblem Badgemaker 5 Bedienungsanleitung

STARTING BADGEMAKING

Badgemaker 5

Instruction Manual

NOTES

• Remove body and handle from packaging and dispose of all packing

• It is important that your Badgemaker is operated in a secure position either

through use of G clamp or mounted onto a board or bolted to a stable

work surface.

• Recommended thickness for prints when used with acetate is

between 80 and 115 gsm (eg. standard photocopying paper is

80gsm).

• After loading die, always ensure that it is located directly under the

top die.

• Metal rings and tops as well as plastic seals can stick together, so always check

that only one at a time is used.

• Never allow the machine handle to spring back.

• When cutting out your prints using the rotary cutter, ensure that you cut out on a suitable surface

such as Perspex, nylon or polypropylene. Any other surface used may damage the blade on the

cutter – suitable boards are available from London Emblem.

STEP BY STEP GUIDE TO BADGEMAKING

Badges

Stage 1: Place metal badge top (rim down) in right hand die in circular slot. Cover with cut out print

(printed side up) and one plastic Swing right hand bottom die anti-clockwise under top die and

pull handle towards you to complete stage.

Stage 2: Place pinned back (zigzag side of pin showing) in left hand die. Swing left hand bottom die

clockwise under top die and pull handle towards you to complete assembly. Swing die set anti-

clockwise to remove badge from machine. If required, turn the back to position design.

25mm Badges

Complete Stage 1 of the badgemaking process. Place metal ring, rim upwards in die. Swing die

clockwise under top die and pull handle towards you to complete assembly. Swing die set

anti-clockwise to remove badge from machine. Insert supplied pin in back.

London Emblem Ltd., 4 Sherwood Road, Aston Fields Industrial Estate, Bromsgrove, Worcestershire, B60 3DR

Tel: +44 (0)1329 822900 • Fax: +44 (0)1329 82900 • Email: [email protected] • www.londonemblem.com

London Emblem Ltd., 4 Sherwood Road, Aston Fields Industrial Estate, Bromsgrove, Worcestershire, B60 3DR

Tel: +44 (0)1329 822900 • Fax: +44 (0)1329 82900 • Email: [email protected] • www.londonemblem.com

Kid Klips

Complete stage 1 of the badgemaking process then place back with writing downwards in the left

hand die. Swing die clockwise under top die and pull handle towards you to complete assembly.

Swing die set anti-clockwise to remove badge from machine.

Mirrors

Complete Stage 1 of the badgemaking process then place metal ring, smooth side down, followed by

mirror glass (mirror face downwards) and cardboard space into the left hand die. Swing left hand die

clockwise under top die and pull handle down towards you to complete assembly. Swing die set anti-

clockwise to remove mirror from machine.

Magnets

Complete Stage 1 of the badgemaking process then place unpinned back (rim upwards) into left hand

die. Swing left hand die clockwise under top die and pull handle to complete assembly. Swing die set

anti-clockwise to remove badge from machine and to complete, peel paper backing from magnet and

stick to the centre of the badge back.

Keyrings

Complete Stage 1 of the badgemaking process then place plastic ring smooth side down into left

hand die. Swing left hand die clockwise under top die and pull handle towards to complete

assembly. Swing die set anti-clockwise to remove badge unit from machine. To complete assembly, clip

keychain through hole in key fob. Locate lugs in fob to plastic ring of badge unit and snap together by

hand. Turn the back to position design.

Photo Stands

Complete Stage 1 of the badgemaking process then place black plastic ring (smooth side down)

into the left hand die. Swing left hand die clockwise under top die and pull handle towards you to

complete assembly. Swing die set anti-clockwise to remove badge unit from machine. To complete

assembly locate lugs in photo stand to black plastic ring of badge unit and snap together by hand.

Turn the back to position design.

Bottle Openers

Complete Stage 1 of the badgemaking process. Remove and turn over die, place the bottle opener in the die.

Locate die back under the machine and move lever facing you in the top die fully to the left.

Pull handle rmly towards you to complete assembly.

Remove nished unit from machine and clip keychain to holes in bottle opener.

London Emblem Ltd., 4 Sherwood Road, Aston Fields Industrial Estate, Bromsgrove, Worcestershire, B60 3DR

Tel: +44 (0)1329 822900 • Fax: +44 (0)1329 82900 • Email: [email protected]om • www.londonemblem.com

TROUBLESHOOTING

If a badge does not make up properly, check:

• That only one top or plastic seal has been used. If two tops or seals are stuck in the top die, they

can be ejected by operating the second stage of badgemaking with the die empty.

• That pressure has been used on the second stage of badgemaking. To ensure perfect

crimping of the badge, pull handle towards you.

CHANGING THE DIE

• Remove bottom die set from base of machine by undoing grub screw (5/29) and lifting out hinge

pin (5/32). Die set can now be lifted o.

• Locate allen screw in underpart of top die and remove by turning in a clockwise direction with allen

key provided.

• Take the required size top die and with obtruding pin towards back of machine, locate the die onto

shaft and ensure that locating pin on top of the die is into the hole at the end of the shaft

and tighten.

• Place required size bottom die set onto base of machine. Locate hinge pin (5/32) through the hole

in the base plate into base of machine. Push down and hold whilst tightening retaining grub

screw (5/29). Do not overtighten.

MAINTENANCE

As with all production machinery, the working surfaces of the machine should be kept clean and free

from dust. Only the very minimum of lubrication, using grease, is advised and this should be applied

only to the surfaces of the shaft assembly and roller on base of handle assembly. It is important to

regularly tighten all screws and bolts. Do not overtighten.

INSTRUCTIONS FOR CHANGING BLADES ON LONDON EMBLEM AND

BADGEWORX CUTTERS

• Turn rotary cutter over.

• Unlock screw in base of main shaft using allen key provided.

• Retract adjustment shaft complete with blade so that grub screw holding retaining pin is accessible.

• Unlock grub screw holding pin.

• Remove blade with retaining pin from the shaft.

• Replace new blade, with side facing inwards, onto retaining pin, relocate into adjustment shaft

and lock down with grub screw, making sure that cutting blade rotates freely.

• Reset adjustment shaft to size required.

Inhaltsverzeichnis

Andere London Emblem Werkzeuge Handbücher

London Emblem

London Emblem Badgeworx Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung