Lorell Peninsula LLR60125 Bedienungsanleitung
Workstation Peninsula
Péninsule de poste de travail
Estación de trabajo “Península”
LLR60125/87301
LLR60125_87301_Manual.indd 1LLR60125_87301_Manual.indd 1 3/7/11 10:09 AM3/7/11 10:09 AM
Page 1 of 18
Instruction:
If you are missing parts or have other concerns, please email Lorell@sprich.com or fax: 404-472-9063.
Please provide the following information:
1. Full Name
2. Physical Address – do not include P.O. Box as our carriers cannot deliver to a P.O. Boxes
3. Phone Number
4. Model Number
5. Part Number
6. Invoice #
7. Date of Purchase
Note: Our policy is to send all parts requests normal ground transportation, if your requirements are to have these parts via
overnight/next day, please provide your designated carrier and account number. Replacement panels are not available. If damaged
has occurred during shipment, please return the entire unit to place of purchase for credit and replacement. Original Invoice may be
required.
Before you begin:
Open, identify and count all parts prior to assembly. Lay out the parts on a non-abrasive surface such
as carpet or blanket. You will need the tools identified below:
1. Phillips Head Screw Driver
2. Flat Head Screw Driver
3. Rubber Mallet (recommended)
4. Hammer
LLR60125_87301_Manual.indd 1LLR60125_87301_Manual.indd 1 3/7/11 10:09 AM3/7/11 10:09 AM
Page 2 of 18
HARDWARE IDENTIFICATION
LLR60125_87301_Manual.indd 2LLR60125_87301_Manual.indd 2 3/7/11 10:09 AM3/7/11 10:09 AM
Page 3 of 18
PANEL IDENTIFICATION
LLR60125_87301_Manual.indd 3LLR60125_87301_Manual.indd 3 3/7/11 10:09 AM3/7/11 10:09 AM
Page 4 of 18
ASSEMBLY INSTRUCTIONS
Step 1
Lay all surfaces on a non-abrasive surface with the holes facing up.
On the Table Top (A) insert 6 each Wood Dowels (4) in the holes shown on the drawing. Tap securely into
position with a Rubber Mallet or Hammer.
On the Table Top (A) insert 6 each Cam Screws (1) with a Phillips Screw Driver in the hole position shown on
the drawing.
On the End Panel (B) insert 2 each Wood Dowels (4) in the hole position shown on the drawing. Tap securely
into position with a Hammer or Rubber Mallet.
On the End Panel (B) insert 3 each Cam Screws (1) with a Phillips Screw Driver in the hole position shown on
the drawing.
On the End Panel (B) insert 2 each Cam Lock (2) in the hole positions shown on the drawing. When inserting
the cam lock make sure that the arrow is facing toward the cam screw entry.
On the Large Support Panel (C) insert 4 each Cam Lock (2) in the hole position shown on the drawing. When
inserting the cam lock make sure that the arrow is facing toward the cam screw entry.
On the Small End Panel (D) insert 2 each Wood Dowel (4) in the hole position shown on the drawing. Tap
securely into place with a Rubber Mallet or Hammer.
On the Small End Panel (D) insert 3 each Cam Screw (1) in the hole position shown on the drawing with a
Phillips Screw Driver.
On the Small End Panel (D) insert 2 each Cam Lock (2) in the hole position shown on the drawing. When
inserting the cam lock make sure that the arrow is facing toward the cam screw entry.
On the Small Support Panel (E) insert 4 each Cam Lock (2) in the hole position shown on the drawing. When
inserting the cam lock make sure that the arrow is facing toward the cam screw entry.
A
Table Top
1
1
1
1
4
4
2
1
4
4
2
14
4
2
2
B
End Panel
C
Large Support Panel
D
Small End Panel E
Small Support Panel
4
LLR60125_87301_Manual.indd 4LLR60125_87301_Manual.indd 4 3/7/11 10:09 AM3/7/11 10:09 AM
Page 5 of 18
Step 2
Attach the Large Support Panel (C) to
the End Panel (B). Make sure that the
3 each Cam Screws on the End Panel
engage with the Cam Locks located
on the Support Panel. With a Phillips
Screw Driver rotate the cam locks 1/2
turn clockwise until snug. DO NOT
OVERTIGHTEN.
Step 3
Attach the Small Support Panel (E) to the
Small End Panel (D). Make sure that the 3
each Cam Screws on the Small End Panel
engage with the Cam Locks located on
the Small Support Panel. With a Phillips
Screw Driver rotate the cam locks 1/2
turn clockwise until snug. DO NOT
OVERTIGHTEN.
Step 4
Attach the Large Support Panel (C)/
End Panel (B) unit to the Table Top (A)
ensuring that the Cam Screws (1) located
in the Table Top (A) properly engage
with the Cam Lock (2). With a Phillips
Screw Driver rotate the cam locks 1/2
turn clockwise until snug. DO NOT
OVERTIGHTEN.
Attach the Small Support Panel (E)/
Small End Panel (D) to the Table Top
(A) ensuring that the Cam Screws (1)
located in the Table Top (A) properly
engage with the Cam Lock (2). With a
Phillips Screw Driver rotate the cam locks
1/2 turn clockwise until snug. DO NOT
OVERTIGHTEN.
LLR60125_87301_Manual.indd 5LLR60125_87301_Manual.indd 5 3/7/11 10:09 AM3/7/11 10:09 AM
Page 6 of 18
Step 5
Attach 12 each Cam Cap (3) to each of
the Cam Locks (2).
Screw the 6 each Adjustable Foot (5) into
the inserts as shown on the drawing.
Carefully turn unit into its upright
position. It is recommended that two
people complete this step!
Step 6 (Optional)
If attaching a LLR60127/87300 Bridge,
mount the Flat Brackets to the Table Top
(A) in the pre-drilled hole positions now.
You have successfully completed the assembly of this unit!
Thank you for your purchase of this item!
LLR60125_87301_Manual.indd 6LLR60125_87301_Manual.indd 6 3/7/11 10:09 AM3/7/11 10:09 AM
Page 7 of 18
Instructions:
Veuillez nous faire parvenir un courriel à lorell@sprich.com ou un fax à : 404-472-9063, s’il vous manque
des pièces ou que vous éprouvez d’autres inquiétudes.
Veuillez fournir l’information suivante :
1. Nom complet
2. Adresse physique – ne donnez pas votre boîte postale car nos livreurs ne peuvent pas livrer à
une boîte postale
3. Numéro de téléphone
4. Numéro de modèle
5. Numéro de pièce
6. # de facture
7. Date de l’achat
Note: Notre politique est de livrer toutes les demandes de pièces par la voie terrestre; prière de fournir le nom de votre transporteur
ainsi que votre numéro de compte si vos exigences sont d’avoir ces pièces livrées pendant la nuit/le lendemain. Des panneaux de
remplacement ne sont pas disponibles. Si des dommages sont survenus durant le transport, prière de retourner l’unité entière à
l’endroit de l’achat pour un crédit et un remplacement. La facture originale peut être exigée.
Avant de commencer:
Ouvrez, identifiez et comptez toutes les pièces avant de procéder à l’assemblage. Disposez les pièces
sur une surface non-abrasive telle un tapis ou une couverture. Vous aurez besoin des outils identifiés
ci-après:
1. Tournevis à tête Phillips
2. Tournevis à tête plate
3. Maillet de caoutchouc (recommandé)
4. Marteau
LLR60125_87301_Manual.indd 7LLR60125_87301_Manual.indd 7 3/7/11 10:09 AM3/7/11 10:09 AM
Page 8 of 18
IDENTIFICATION DE LA QUINCAILLERIE
LLR60125_87301_Manual.indd 8LLR60125_87301_Manual.indd 8 3/7/11 10:09 AM3/7/11 10:09 AM
Page 9 of 18
IDENTIFICATION DES PANNEAUX
LLR60125_87301_Manual.indd 9LLR60125_87301_Manual.indd 9 3/7/11 10:09 AM3/7/11 10:09 AM
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Lorell Desktop Handbücher
