Lorex CA453 Bedienungsanleitung

www.lorexcctv.com

5” B&W Rear View

System Camera

Instruction Manual

MODEL:

CA453

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO A QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

OF PLUG TO WIDE SLOT, FULLY INSERT.

Thank you for purchasing the Lorex 5” Black & White Rear View System Camera. This

system helps to prevent backing-up and parking accidents by allowing you to view or

check on the traffic behind your vehicle, or when rounding corners (blind spot

prevention).

This system is suitable for waste trucks, RV campers, vans, delivery vehicles &

cars.To learn more about this system or to find out more about our products available,

please visit our website at:

http://www.lorexcctv.com

Warning: This Rear Observation System is to be used with, not instead of, other

viewing aids in your vehicle such as front, rear, and side mirrors. Safe driving

practices, alertness, and visual and physical fitness are prerequisites for your driving

safety. The Manufacturer shall not be held liable for any accidents which may occur

while operating this system.

General Precautions

FCC CLASS B NOTICE

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instruction, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception (which can be determined by turning the equipment on

and off), the user is encouraged to try to correct the interference by one or more of the following measures:

zReorient or relocate the receiving antenna

zIncrease the separation between the equipment and receiver

zConnect the equipment into an outlet on a circuit different from that to which the receiver is

connected

zConsult the dealer or an experienced radio or television technician for assistance

LOREX TECHNOLOGY INC.

http://www.lorexcctv.com

NOTE

This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and LVD. Therefore, it

is designated to provide reasonable protection against interference and will not cause interference with other appliance

usage.

However, it is imperative that the user follows this manuals guidelines to avoid improper usage which may result in

damage to the unit, electrical shock and fire hazard injury

In order to improve the feature functions and quality of this product, the specifications are subject to change without

notice from time to time.

General Precautions

1. All warnings and instructions of this manual should be followed

2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a water dampened cloth

for cleaning

3. Do not use this unit in humid or wet places

4. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet should not be blocked

5. During lightning storms, or when the unit is not used for a long time, disconnect the power supply, antenna, and cables

to protect the unit from electrical surge

Table of Contents

Getting Started .......................................................................................... 5

Camera Installation ................................................................................... 5

Mounting the Cameras and Cables .......................................................... 6

Camera Overview ..................................................................................... 6

Full Connection Diagram .......................................................................... 7

Operating Instructions ............................................................................... 7

Camera Specifications - Appendix #1 ....................................................... 8

Lorex CVA453 Accessory Cables - Appendix #2....................................... 9

CA453 FEATURES

• Automatic switching of camera when gear is shifted into reverse

• Built-in microphone on camera (One-way audio).

• Waterproof, light sensitive, CCD sensor camera in a compact die-cast housing

• Wide Field of View: 94°Horizontal 72°Vertical 110°Diagonal

• 2 piece Waterproof Camera connecting cable (prevents corrosion & resistant to weathering)

with 4 pin connector

Getting Started

The CA453 Camera comes with the following components:

CHECK YOUR PACKAGE TO CONFIRM THAT YOU HAVE RECEIVED THE COMPLETE

SYSTEM, INCLUDING ALL COMPONENTS SHOWN ABOVE.

65’ (2 Piece) Camera Extension Cable1/3” CCD Weatherproof Camera

Camera Installation

1. Connect the 1.8 M cable from the camera to the short 5M piece of the 20M (15M + 5 M) 2-piece

extension cable provided.

2. Connect the other end of the 5M cable to the 15M piece, which connects to CAM 1 or CAM 2

on the back of the monitor

Mounting the Cameras and Cables

1. Determine the desired camera mounting position. Install the bracket into position using the

supplied screws on the center and slide holes.

2. Adjust the bracket to the left and right to set the position, and tighten the screws.

3. Install the camera to the bracket using the supplied washers, spring washers and screws.

4. Adjust the camera to the desired position (make sure the picture is clear and pointed in the

correct direction). Tighten the screws.

5. Drill a cable entry hole through the frame, door or window frame just below the mounting bracket.

6. Pull the cable fully through the hole. Once the cable has been pulled through, attach the extension

cable to the camera.

7. Run the extension cable to the Monitor.

8. Shield the hole that you made for the cable.

NOTE: Do NOT connect the camera(s) to the monitor while the system is powered on. Failure to

properly connect the cameras may cause damage and invalidate the warranty.

Camera Overview

Full Connection Diagram

1. Connect the RED wire to the (12V – 32V DC) power terminal, which powers the system when

the ignition key is turned on the vehicle.

2. Connect the BLACK wire to a metal portion of the vehicle or the negative battery post.

3. Connect the BROWN wire to the switched power output terminal of the “R” (reverse) gear.

4. Connect the WHITE wire to the Dimmer line.

Operating Instructions

• When you turn the ignition key to the ON position, power is supplied to the monitor. The

monitor will automatically be in standby mode, even if the Power button is not pushed in.

• When you push the power button you can manually view the picture from the camera(s).

• When the power button is not pushed in, and you shift the gear into reverse, the monitor will

automatically display the image from selected Camera (if the Auto/Manual switch is in the

AUTO position).

Camera Specifications - Appendix #1

As our products are subject to continuous improvement, LOREX Technology Inc. and its

subsidiaries reserve the right to modify product design, specifications and prices, without notice

and without incurring any obligation. E&OE

Pick-up Device 1/3” B&W CCD

Number of Pixels 512 x 492 (EIA)

Fixed Focus Lens 2.5mm

Viewing Angle 110°Diagonal

Horizontal Resolution 380 TV Lines

Video Output 1V p-p, 75 ohms

Minimum Illumination 0.3 Lux

Shock / Vibration Rating 6.8g @ 0~2000 Hz

Input Voltage Range 9.5~14V DC from the monitor

Operating Temperature 14°F ~ 122°F

-30°C ~ 50°C

Dimensions 2.76” (W) x 1.97” (H) x 1.97” (D)

70mm (W) x 50mm (H) x 50mm (D)

Weight 0.75 lbs / 0.34 kg

Lorex CVA453 Accessory Cables - Appendix #2

Additional adapter cables are available for backward compatibility between the Lorex 452 Series

and the Sentinel CCTV 452 Series Rear view systems.

Adaptor Cable #3 - CA453 (Camera) to

CA452 (Camera Extension Cable)

Connects the Lorex CA453 Camera to the Sentinel

CA452 Camera Extension Cable.

Adaptor Cable #2 - CA453 (Camera

Extension Cable) to MO452 (Monitor)

Connects the Lorex CA453 Camera Extension

Cable to the Sentinel MO452 Monitor.

Adaptor Cable #1 - CA452 (Camera

Extension Cable) to MO453 (Monitor)

Connects the Sentinel CA452 Camera Extension

Cable to the Lorex CA453 Monitor.

It’s all on the web

Product Information

User Manuals

Quick Start Guides

Specification Sheets

Software Upgrades

Firmware Upgrades

Lorex Technology Inc.

VISIT

wwwlorexcctv.com

www.lorexcctv.com

Inhaltsverzeichnis

Andere Lorex Dashcam Handbücher

Lorex

Lorex RV453 Bedienungsanleitung

Beliebte Dashcam Handbücher anderer Marken

Cansonic

Cansonic UltraDuo Z2 Bedienungsanleitung

Gazer

Gazer F720 Bedienungsanleitung

HP f500g Bedienungsanleitung

Xblitz

Xblitz TANGO 4K Bedienungsanleitung

Rexing

Rexing M1 Bedienungsanleitung

Maka Technologies

Maka Technologies Marbella MXPro Bedienungsanleitung

NESA

NESA NRC-80DLM Montage- und Bedienungsanleitung

Kaiser Baas

Kaiser Baas R20 Bedienungsanleitung

Boyo

Boyo VTM43TC Bedienungsanleitung

Minolta

Minolta MNCD37 Bedienungsanleitung

Thinkware

Thinkware FA10 Bedienungsanleitung

Momento

Momento MD-5200 Bedienungsanleitung

BlackVue

BlackVue DR590X-1CH Bedienungsanleitung

HP F300 Bedienungsanleitung

CammSys

CammSys BlackSys BH-300 Bedienungsanleitung

Snooper

Snooper DVR-2HD Bedienungsanleitung

Lukas

Lukas Q900 Bedienungsanleitung

RVS

RVS 450C Bedienungsanleitung