Lorex RV453 Bedienungsanleitung

www.lorexcctv.com

5”B&W Rear View

Safety System

Instruction Manual

English Version 1.0

MODEL:

RV453

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO A QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

OF PLUG TO WIDE SLOT, FULLY INSERT.

Thank you for purchasing the Lorex 5” Black & White Rear View Safety System. This

system helps to prevent backing-up and parking accidents by allowing you to view or

check on the traffic behind your vehicle, or when rounding corners (blind spot

prevention).

This system is suitable for waste trucks, RV campers, vans, delivery vehicles &

cars.To learn more about this system or to find out more about our products available,

please visit our website at:

http://www.lorexcctv.com

Note: Includes the MO453 monitor & CA453 camera

Warning: This Rear Observation System is to be used with, not instead of, other

viewing aids in your vehicle such as front, rear, and side mirrors. Safe driving

practices, alertness, and visual and physical fitness are prerequisites for your driving

safety. The Manufacturer shall not be held liable for any accidents which may occur

while operating this system.

General Precautions

FCC CLASS B NOTICE

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instruction, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception (which can be determined by turning the equipment on

and off), the user is encouraged to try to correct the interference by one or more of the following measures:

zReorient or relocate the receiving antenna

zIncrease the separation between the equipment and receiver

zConnect the equipment into an outlet on a circuit different from that to which the receiver is

connected

zConsult the dealer or an experienced radio or television technician for assistance

LOREX TECHNOLOGY INC.

http://www.lorexcctv.com

NOTE

This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and LVD. Therefore, it

is designated to provide reasonable protection against interference and will not cause interference with other appliance

usage.

However, it is imperative that the user follows this manuals guidelines to avoid improper usage which may result in

damage to the unit, electrical shock and fire hazard injury

In order to improve the feature functions and quality of this product, the specifications are subject to change without

notice from time to time.

General Precautions

1. All warnings and instructions of this manual should be followed

2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a water dampened cloth

for cleaning

3. Do not use this unit in humid or wet places

4. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet should not be blocked

5. During lightning storms, or when the unit is not used for a long time, disconnect the power supply, antenna, and cables

to protect the unit from electrical surge

Table of Contents

Getting Started .......................................................................................... 5

RV453 - Front ........................................................................................... 6

RV453 - Back ............................................................................................ 7

Camera Installation ................................................................................... 8

Mounting the Cameras and Cables .......................................................... 8

Camera Overview ..................................................................................... 9

Monitor Overview ...................................................................................... 9

Monitor Installation .................................................................................. 10

Connecting the Monitor Power ................................................................ 10

Full Connection Diagram ........................................................................ 11

Operating Instructions ............................................................................. 11

System Specifications - Appendix #1 ...................................................... 12

Camera Specifications - Appendix #2 ..................................................... 13

Lorex CVA453 Accessory Cables - Appendix #3..................................... 14

RV453 FEATURES

• Automatic activation of camera when gear is shifted into reverse.

• Built-in 2 Camera input.

• Built-in microphone on camera (One-way audio).

• Built-in Brightness, Contrast and Volume Control.

• Selector switch for Normal and Reverse image viewing.

• Waterproof B&W CCD image sensor camera in a compact die-cast housing.

• Input voltage 12-32 Volt DC.

• Monitor equipped with day/night selector switch for brightness compensation.

• Wide Field of View: 94°Horizontal 72°Vertical 110°Diagonal.

• 2 piece Waterproof Camera connecting cable (prevents corrosion) with 4 pin connector.

• Camera selector switch.

Getting Started

The RV453 Rearview System comes with the following components:

CHECK YOUR PACKAGE TO CONFIRM THAT YOU HAVE RECEIVED THE COMPLETE

SYSTEM, INCLUDING ALL COMPONENTS SHOWN ABOVE.

Mounting Hardware and Brackets

for Monitor and Camera

65’ (2 Piece) Camera Ex-

tension Cable

Sunshade for Monitor

Power cable and Harness

1/3” CCD Weatherproof

Camera

5” B&W CRT Monitor

RV453 - Front

1. POWER SWITCH - Turns the monitor ON/OFF:

• Press the power switch to turn the monitor ON. The green LED indicator will illuminate.

• Press the power switch again to turn the monitor OFF (STANDBY MODE).The green LED

indicator will extinguish.

NOTE: When you shift into reverse gear, the monitor will automatically display the image from

Camera 1, when the system is in Auto mode.

2. CONTRAST CONTROL - Adjusts the contrast control for the optimal picture. Turn the dial

clockwise to increase the picture contrast, and counterclockwise to decrease it.

3. BRIGHTNESS - Adjust the brightness control for the desired optimal picture. Turn the dial

clockwise to increase the picture brightness, and counterclockwise to decrease it.

4. VOLUME CONTROL - Adjusts the volume to the Monitor. Turn the control clockwise to increase

the volume, and counterclockwise to decrease it.

5. CAMERA SWITCHER (C1 / C2) - Press the Camera Switcher button to switch the picture view

from Camera 1 to Camera 2 (second camera is sold separately).

• Press the button in to switch to Camera 1.

• Press the button again to switch to Camera 2.

NOTE: When the vehicle changes into reverse gear, the system will automatically display the

picture from Camera 1, regardless of the Camera Switcher position.

6. MODE CONTROL - Sets the system to Automatic or Manual camera switching. Press the button

in to select Automatic switching mode. Press the button again to select Manual switching mode.

NOTE: When you shift into reverse gear, the monitor will automatically display the image from

Camera 1, when the system is in Auto mode. The selected camera will be displayed regardless

of the power switch position.

7. BRIGHT CONTROL - Automatically optimizes the picture to compensate for daylight or night.

Press the button in to select Night mode. Press the button again to select Daylight mode.

123 4 5 67

RV453 - Back

1. CAMERA 1 / CAMERA 2 INPUTS - Allows 2 Cameras (4-Pin) to connect to the system.

• Connect the provided camera to the first channel (C1).

• An additional camera can be connected to C2 (not included).

• Connect the B&W video camera to the monitor with the supplied cable.

• The monitor supplies power to the cameras

2. VIDEO OUTPUT - Connects the system video to a second TV or monitor using a Video RCA

cable (not included), or to the Video input of a VCR/DVR for recording.

3. AUDIO OUTPUT - Connects the system audio to a second TV or monitor using an Audio RCA

cable (not included), or to the Audio input of a VCR/DVR for recording.

4. EXTERNAL SPEAKER PORT - Connects the system to external Speakers (not included).

5. MIRROR / NORMAL SWITCH - Changes the view on Camera 1 and Camera 2 to Mirrored or

Normal view.

NOTE: This switch has been set to Mirror (Reversed Image) during production. When viewing

behind the vehicle when reversing, confirm that this switch is set to the MIR position. Make sure

the image appearing on the display is reversed right to left, just as it appears in a rear-view

mirror.

6. POWER CONNECTOR - Insert the supplied power cable connector firmly until it is locked in

place. To remove the power connector, press and hold the clip, and pull out.

12 3 4 5 6

Camera Installation

1. Connect the 1.8 M cable from the camera to the short 5M piece of the 20M (15M + 5 M) 2-piece

extension cable provided.

2. Connect the other end of the 5M cable to the 15M piece, which connects to CAM 1 or CAM 2

on the back of the monitor

Mounting the Cameras and Cables

1. Determine the desired camera mounting position. Install the bracket into position using the

supplied screws on the center and slide holes.

2. Adjust the bracket to the left and right to set the position, and tighten the screws.

3. Install the camera to the bracket using the supplied washers, spring washers and screws.

4. Adjust the camera to the desired position (make sure the picture is clear and pointed in the

correct direction). Tighten the screws.

5. Drill a cable entry hole through the frame, door or window frame just below the mounting bracket.

6. Pull the cable fully through the hole. Once the cable has been pulled through, attach the extension

cable to the camera.

7. Run the extension cable to the Monitor.

8. Shield the hole that you made for the cable.

NOTE: Do NOT connect the camera(s) to the monitor while the system is powered on. Failure to

properly connect the cameras may cause damage and invalidate the warranty.

Camera Overview

Monitor Overview

Monitor Installation

1. Determine the location to mount the monitor. Install the monitor mounting bracket by placing the

screw into the center hole. Rotate and adjust the bracket by turning it left and right for the best

placement. Screw in the slide holes on the bracket and tighten the screws.

2. Mount the monitor onto the bracket by using the supplied screws. Adjust the monitor up and

down to the best position and tighten the screws.

3. If necessary attach the sun shield on top of the monitor.

Connecting the Monitor and Cables

1. Connect the cameras to the camera input sockets marked C1 and C2 on the back of the monitor.

NOTE: Connect the backup (reverse gear) camera into the C1 (camera 1) port.

2. Plug the power harness into the socket marked POWER at the back of the monitor.

Connecting the Monitor Power

The diagram below outlines the connections for the power cable:

NOTE: The Red wire with the fuse holder should be connected to vehicle ACC Terminal; the

Brown wire to reverse gear relay; and the Black wire to the chassis ground.

Inhaltsverzeichnis

Andere Lorex Dashcam Handbücher

Lorex

Lorex CA453 Bedienungsanleitung

Beliebte Dashcam Handbücher anderer Marken

Cansonic

Cansonic UltraDuo Z2 Bedienungsanleitung

Gazer

Gazer F720 Bedienungsanleitung

HP f500g Bedienungsanleitung

Xblitz

Xblitz TANGO 4K Bedienungsanleitung

Rexing

Rexing M1 Bedienungsanleitung

Maka Technologies

Maka Technologies Marbella MXPro Bedienungsanleitung

NESA

NESA NRC-80DLM Montage- und Bedienungsanleitung

Kaiser Baas

Kaiser Baas R20 Bedienungsanleitung

Boyo

Boyo VTM43TC Bedienungsanleitung

Minolta

Minolta MNCD37 Bedienungsanleitung

Thinkware

Thinkware FA10 Bedienungsanleitung

Momento

Momento MD-5200 Bedienungsanleitung

BlackVue

BlackVue DR590X-1CH Bedienungsanleitung

HP F300 Bedienungsanleitung

CammSys

CammSys BlackSys BH-300 Bedienungsanleitung

Snooper

Snooper DVR-2HD Bedienungsanleitung

Lukas

Lukas Q900 Bedienungsanleitung

RVS

RVS 450C Bedienungsanleitung