Louroe Electronics Verifact K Bedienungsanleitung

The Verifact™ K is a dynamic line level microphone with pre-amp and is designed

for areas with excessive background noise or where the ambient sound level is high.

The modified omni-directional pattern is one in which the audio pickup is more from

the front of the microphone and less from the sides and back.

When mounting, position the Verifact™ K so that the front part (white screen) is

facing the desired area of coverage. Microphone functions best when it is mounted

close to the source, 3’ - 8’ away.

IMPORTANT - REDUCE VIBRATION

If installation is in a moving vehicle

(bus, police van, tram, etc.), The

Verifact™ K may require a Louroe™

shock mount assembly to reduce

vibration and to enhance clarity of both

live and recorded audio. Model number

is Verifact™ K Shock Mount.

Verifact™Model

K Microphone

Verifac™t K Shock Mount

(optional)

VERIFACT™K

MICROPHONE

INSTALLATION AND OPERATING INSTRUCTIONS

Page 1 of 4 K_mic_inst_4/11

6955 VALJEAN AVE, VAN NUYS, CA 91406

PH: (818)994-6498 / FAX: (818)994-6458

/ www.louroe.com[email protected]

CONNECTION TO A LOUROE BASE STATION OR TO IF-1, IF-4, IF-8 INTERFACE

ADAPTER:

After microphone connection has been made, run cable to the Louroe Base Station or Interface Adapter. All

Louroe Base Stations and Interface Adapters have a corresponding terminal block (A, B, C) for each zone.

Make connections to the terminal block from microphone wire, matching A to A, B to B and C to C. If using

cable from other manufacturers with a different color code, make certain that wire colors are properly matched

between microphone and base station.

CONNECTION TO A LOUROE MICROPHONE MIXER (RN-2 or MLA-6)

Refer to Installation Instructions for the specified mixer.

IF MODEL K MICROPHONE IS BEING CONNECTED DIRECTLY TO A SOURCE OTHER THAN A LOUROE

BASE STATION OR INTERFACE ADAPTER (DVR, IP NETWORK CAMERA, ETC), CONNECT AS

FOLLOWS:

1. Apply 12Vdc power to terminals A and C.

(A is positive, C is negative)

2. Connect Terminal B (audio out) and Terminal C of Verifact™ K Microphone to the recorder or audio source

using single conductor shielded cable, 22 gauge with a drain wire.

3. If the audio input of the recorder (or other source) is an RCA receptacle, solder on an RCA plug with

terminal B wire going to tip of jack, and terminal C wire soldered to sleeve of jack.

MICROPHONE CONNECTION

On the back plate of the Verifac™t K is a terminal strip

marked A, B, C:

A = 12Vdc (positive) Red Wire

B = Audio Out Black Wire

C = Ground (negative) Bare Wire

Using recommended wiring:

1 - Connect RED wire to terminal A

2 - Connect BLACK wire to terminal B

3 - Connect Bare wire to terminal C

2 Conductor shielded cable, 22

gauge with a 24 gauge drain

wire.

West Penn 452 or equivalent

NOTE: Unshielded cable is not

satisfactory for audio

systems.

WIRING REQUIREMENTS

VERIFACT™MODEL K MICROPHONE

WITH SHOCK MOUNT ASSEMBLY

MODEL K MICROPHONE

MOUNTING SHOE

MOUNTING PLATE

NYLON WASHER

LOCK NUT

SHOCK ABSORBERS

(Screws provided)

(6-32x¾) IMPORTANT: Make certain that wires are

attached to

microphone’s terminal

strip BEFORE installing

microphone to shock

mount assembly.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 2 of 4

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

K_mic-inst_4/11

VERIFACT™K MICROPHONE CONNECTION

TO A LOUROE™BASE STATION

IF-1, IF-4, IF-8 AUDIO INTERFACE ADAPTER

Back side of

Verifact™ K

Microphone

A = 12Vdc

B = Audio Output

C = Ground

SENSITIVITY SWITCH

N = Normal

L = Low

Position L lowers the gain

by -6dB output into 1KΩand

is used when there is

excessive background

noise, or if less microphone

sensitivity is desired.

2 CONDUCTOR

SHIELDED

22 GAUGE

WITH A 24 GAUGE

DRAIN WIRE

WEST PENN

452 OR EQUIV.

BLACK BARE

RED

BARE

RED

A B C

BLACK

Verifact™ K

Microphone

To Receiving Device

(Base Station, Interface Adapter or Mixer)

INSTALLATION AND OPERATING INSTRUCTIONS

Page 3 of 4

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

K_mic-inst_4/11

SPECIFICATIONS

Frequency Response

Output

Current Drain

100 Hz to 15 kHz ± 1 dB

Line Level (0 dB @ 1000Ω)

4 mA

Supply voltage 12 Vdc

Output Impedance (Mic only) 600 , unbalanced

Dimensions 5 7/8”L x 3 1/8 “W

Type Dynamic

Polar Pattern Modified Omni-Directional

IMPORTANT NOTICE

When this equipment is used as part of an

audio monitoring system, the law requires

that the public be given notice of AUDIO

MONITORING ON THE PREMISES. A

decal notice is included with each

microphone shipped.

Federal Law References:

Federal Regulations, US Code, Title 18.

Crime and Criminal Procedure, Sec 2510.

INSTALLATION AND OPERATING INSTRUCTIONS

Page 4 of 4

LOUROE ELECTRONICS 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458

website: www.louroe.com e-mail: [email protected]

(818)

K_mic-inst_4/11

WARRANTY

LOUROE ELECTRONICS warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS to be free of defects in material and workmanship.

Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS will, at its sole discretion, repair or replace the defective equipment.

This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS .

This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation

instructions provided by LOUROE ELECTRONICS.