LRS T9550 LCK Bedienungsanleitung

Usage, Installation, Warranty and Service Information

Long Range Systems, LLC

4550 Excel Parkway, Suite 200

Addison, TX 5001

800.43 .4996 •www.pager.net

800.437.4996

1234

5 6 78

101112

PGRPROG

ENTER

Long Range Systems

www.pager.net

T9550LCK

Long Range Systems

T9550 LCK

Paging System Transmitter

USER MANUAL

Table Of Contents

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Long Range Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Basic Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Hardware Provided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Transmitted/Keypad Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Keypad Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Basic Paging Operation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Paging All Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setting the Vibration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

System Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Set Restaurant ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Maintenance Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Range Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Check the Transmitter Battery Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Battery Charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Programming Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

T9550 LCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rechargeable Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Transmitter Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Service Questions and Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Long Range Systems 1T9550 LCK User Manual

Long Range Systems

Long Range Systems is a provider of cutting-edge onsite paging solutions. We offer exceptional products and

services that satisfy our customer’s needs for years to come. Thorough familiarity with these instructions and

procedures will ensure proper operation and maintenance of the system.

NOTE: This guide should be kept readily available for managers and key staff.

General Information

The T9550 LCK is an onsite paging system used to increase efficiency in operations by alerting key staff of

immediate needs. The pagers used with the system can vibrate once, twice or three times.

NOTE: The T9550 LCK only works with LRS Star Pagers

Long Range Systems 2T9550 LCK User Manual

800.437.4996

www.pager.net

Long Range Systems

800.437.4996

1234

5678

10 11 12

PGR PROG

ENTER

Long Range Systems

www.pager.net

T9550LCK

STAR PAGER

LED’s

Basic Installation and Setu

Hardware Provided

Each T9550 LCK transmitter kit contains:

(1) Transmitter keypad

(1) Antenna

(1) Dry-Erase Server Board

(1) 10VAC 2A power supply/charger

(1) Velcro strip for mounting

Installation Procedure

The following is the basic installation procedure

CAUTION:

• Do not connect any other devices to the transmitter.

• The transmitter requires a dedicated power supply.

• Mounting the keypad antenna near any large metal objects will minimize the operating range.

NOTE: The keypad should be charging whenever not in use.

1. Unwrap all system components.

2. Locate the silver connector located on the top of the transmitter unit. Twist the antenna (about 3"

long) onto the connector.

3. Plug the power adapter/charger into a standard 110V outlet, and insert the barrel connector end

into either of the side holes on the transmitter unit.

4. Press (hold for 5 seconds) and release the power-reset button located on the side of the trans-

mitter unit. The keypad display will light.

5. Within 5-10 seconds, the display light will disappear signifying that the transmitter is charging

(The display screen will be blank).

6. Upon completion of setup, allow the keypad to fully charge for at least 12 hours before use. Be sure

that pagers are also fully charged.

Mountin :

The transmitter unit can be mounted onto a wall surface.

• Use the Velcro mounting strip to mount the transmitter unit. Be sure to mount the unit close to a

standard 110 V power outlet.

Portable Use:

The transmitter is rechargeable and can be used without the power supply.

• Disconnect the power supply from the transmitter unit to operate under battery power. Be sure to

plug the power supply back into the transmitter when not in use to recharge the battery.

Long Range Systems 3T9550 LCK User Manual

Transmitter/Keypad Elements

Power-Reset Button:

Used when the transmitter’s battery is either depleted or low and needs to be charged. When pressed

and released, the power-reset button ensures proper charging.

Dry-Erase Server Board:

Write the staff names on the label next to their pager number with a NON-PERMANENT, Dry-Erase

Marker or grease pencil.

Keypad Functions

Before using the keypad, read the following key descriptions:

Number Keys:

The number keys 1 through 12 are “one touch” keys to instantly send a message to pagers num-

bered 1 – 12.

Function Keys:

The function keys are located on the last row of the transmitter keypad.

PGR – Used when entering pager numbers above 12.

0– Used when entering pager numbers above 12 that contain a zero and when calling all

pagers at once.

PROG – Used to alter messaging modes and to check the battery level.

ENTER – After entering pager numbers above 12, press ENTER to send the page.

LongRangeSystems

800.437.4996

1234

5678

101112

PGRPROG

ENTER

LongRangeSystems

www.pager.net

T9550LCK

Jerry

Thomas

Susan

CONDOR

CLASS2TRANSFORMER

(408)745-7141

INPUT:AC12OV60Hz19w

OUTPUT:AC9V1800mA

P/N:A91A8

RoHS

LISTED

MODEL:48A-9-1800

EIA3630635S

MADEINCHINA

Antenna

Dry-Erase

Server Board

Power-Reset

Button

Keypad

Function Keys

120VAC

Electrical

Supply

Power

Supply/Charger

Long Range Systems 4T9550 LCK User Manual

Basic Paging O erations

NOTE: The T9550 LCK factory defaults are the most commonly used settings. (All units are set to

vibe 1 time as the default.)

Pa in

For pagers numbered 1 – 12:

1. Press the pager number

2. The unit will automatically send a page

For pa ers numbered 13 and hi her:

1. Press PGR

2. Enter the pager number (using the 0 – 9 keys)

3. Press the ENTER key

Pa e All Call

If all staff pagers need to be called simultaneously:

1. Press PGR

2. Press 0 - 0 - 0

3. Press the ENTER key

Long Range Systems 5T9550 LCK User Manual

SYSTEM SETTINGS

Settin the Vibration Mode

Vibration mode determines the number of times a pager will vibrate when paged.

NOTE: The factory default setting for vibration mode is 1 vibration. (EX: When a page is sent from

the transmitter, the pager will vibrate once)

To set the vibration mode, use the followin steps:

• 1 vibration: Press PROG

Enter 9 - 2 - 1 and press ENTER

• 2 vibrations: Press PROG

Enter 9 - 2 - 2 and press ENTER

• 3 vibrations: Press PROG

Enter 9 - 2 - 3 and press ENTER

• Page a pager (see pg. 6) to ensure that the pager vibrates the number of times programmed

System Reset

If the transmitter’s battery has been completely depleted, it may require a system reset before operating

properly. When the system is reset, the Restaurant ID (see pg. 7) and vibration mode (see pg. 7) will be set

to factory default.

To reset the transmitter to factory default:

1. Press PROG

2. Enter 0 - 0 - 0 and press ENTER

Set Restaurant ID

NOTE: The T9550 LCK is shipped factory defaulted in the most commonly used configuration.

• The Restaurant ID factory default setting is 0.

Your system may or may not be shipped with the factory default setting ID = 0. However, this ID# is often used,

except in cases where neighboring establishments both use LRS systems and would interfere with each

other. Contact LRS to verify your Restaurant ID. (It is not recommanded to change system ID without speak-

ing to LRS service departments.)

To chan e the ID:

1. Press PROG

2. Enter 9 - 0 - # (EX: 9 – 0 – 3, Restaurant ID = 3)

3. Press ENTER

Long Range Systems 6T9550 LCK User Manual

Long Range Systems 7T9550 LCK User Manual

Maintenance Functions

Ran e Test

Perform a range test to determine the furthest point a pager will receive the signal of the T9550LCK.

NOTE: Be sure to remove pagers from the charging base before performing the range test.

1. Press PROG

2. Enter 9 - 1- 2 and press ENTER

3. When the “0” begins scrolling across the screen, pagers will vibrate every 5 seconds (as long as

they are receiving the signal)

4. Take a pager and walk around the area to verify that the pagers operate in all areas

5. When a pager stops vibrating every 5 seconds, it is out of range and is no longer receiving a sig-

nal from the transmitter

Check the Transmitter Battery level

1. Disconnect barrel end of the power adapter from the transmitter unit.

2. Press PROG and then ENTER.

The unit will show a number from 0 to 5:

• If plugged in – it does not matter.

• If the unit shows 4 or above – the charge is adequate for normal use.

• If the unit shows 3 – it is ok for short term use (1 - 2 hours).

• If the unit shows 2 or less (including blank) – it must be recharged before use.

Battery Char e

If the battery power has been completely depleted:

1. Plug the power supply/charger into the transmitter unit.

2. After 10 seconds press and release the power-reset button located on the side of the transmitter.

The display will light.

3. Within 5-10 seconds, the display light will disappear and the screen will remain blank. This is an

indication that the battery is charging.

4. Allow the keypad to charge for at least 12 hours.

5. Check the battery level to ensure that the battery is fully charged (see pg. ).

Programming Pagers

Only LRS’s Star Pagers can be reprogrammed from the T9550 LCK transmitter. If you would like to assign

or reassign numbers to pagers, contact LRS to verify your restaurant ID before proceeding.

The followin is the basic procedure for pro rammin pa ers:

1. Be sure to set the LCK for the restaurant ID in use (See “Restaurant ID” pg. 7).

2. Remove the pager from the charger and wait until it stops vibrating. (Note: remove only one pager

at a time during programming)

3. Press PROG

4. Enter the number you wish to assign to the pager (Choose #: 1 – 99).

5. Press PROG

6. After the pager completes one glow mode cycle, page it to ensure that it’s programmed correctly

(See “Basic Paging Operations” pg. 6).

7. Repeat Steps 2 through 6 for each pager to program.

System S ecifications

Notice: Operation is subject to the followin :

• This device may not cause interference.

• This device will accept any interference including interference that may cause undesired oper-

ation of the unit.

T9550 LCK

Required Voltage: One-110V outlet for the transmitter keypad.

Operating Frequency: 467.750MHz

Radiated Power: <4900 micro-volts/meter

Operating Range: Dependent upon the paging environment.

Rechar eable Pa er

Required voltage: (1) 110V outlet for 10VAC pager charger adapter.

Batteries: Rechargeable Nickel Metal Hydride (NiMH).

Battery life of pager: Approximately 4 hours (dependant on usage). Recharge time: 12 hours mini-

mum from completely “dead”.

Long Range Systems 8T9550 LCK User Manual

Troubleshooting

Transmitter Unit

The Li ht On The Keypad Display Does Not Come On When A Key Is Pressed

• Perform a battery charge (see pg. ), and check for a light after 30-minutes.

• If the display still does not light, check the charging power supply by plugging the power/charg-

ing supply used for the pager charger into the transmitter unit.

• If the display light comes on, there may be a problem with the T9550LCK power/charging sup-

ply. Call LRS Customer Support to order a new power supply.

• If the display still does not light, there may be a problem with the transmitter unit. Call LRS Cus-

tomer Support for assistance.

The Keypad Display Is Functionin Properly But The Pa er Does Not Receive the Pa e

• Perform a system reset (see pg. 7).

• Complete the steps for paging a pager (see pg. 6).

• If the pager still does not receive the page, call LRS Customer Support for assistance.

Pa ers

Pa er Char e Li hts Do Not Come On

Pager charger should display a single red charge light when they are placed in the charger, and are charg-

ing correctly. If the red charge light is not visible on some or all charging slots, review the following recom-

mendations to determine and solve the problem.

• Make sure the pagers are completely inserted into the charging slot.

• The power supply may be defective. Try plugging the power supply used for the transmitter

into the pager charger.

• You may have more pagers charging on one power supply than recommended. Only 25 pagers

can be charged on one 10V power supply. If you have more than 25 pagers, you should call LRS

to order additional chargers.

• You may have a jumper wire that is not properly connected. Look on the side of your chargers

and verify that all wires are connected properly. If they are connected, then the metal contacts

on your pager may be dirty. Using a damp rag, clean the 2 metal contacts on the back of each

pager.

• Be sure that your staff is not disconnecting the power supply at anytime or that you do not have

the charger connected to a circuit that automatically shuts off after hours. The charging base

should be plugged into a power outlet that is “ON” at all times (Be sure the pager is not in the

charger backwards).

• If none of these recommendations solve your problem, call LRS Customer Support to deter-

mine the problem at 00-437-4996.

Long Range Systems 9T9550 LCK User Manual

Andere Handbücher für T9550 LCK

Inhaltsverzeichnis

Andere LRS Sender Handbücher

LRS

LRS T9601 Bedienungsanleitung

LRS

LRS Butler XP Betriebsanleitung

LRS

LRS TX-7470-C232 Bedienungsanleitung

LRS

LRS Freedom T7460 Bedienungsanleitung

LRS

LRS TX-9601 Bedienungsanleitung

LRS

LRS TX-7471-C232 Bedienungsanleitung

LRS

LRS Table Genie Technisches Datenblatt

LRS

LRS Freedom TX-7471 Bedienungsanleitung

LRS

LRS TX-9560MT Bedienungsanleitung

LRS

LRS Freedom Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS T74C232 Bedienungsanleitung

LRS

LRS T9100 Bedienungsanleitung

LRS

LRS T9601 Bedienungsanleitung

LRS

LRS T9550 LCKG Bedienungsanleitung

LRS

LRS Butler II TX-1605-5 Betriebsanleitung

LRS

LRS T7450A Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS T7503 Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS Butler II Bedienungsanleitung

LRS

LRS T9601 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung