LSIS SV-iS7 series Bedienungsanleitung
iS7 CC-Link IE Field Manual
1
Thank you for purchasing iS7 CC-Link option board of LS Variable Frequency
Drives!
Safety Instruction
To prevent injury and danger in advance for safe and correct use of the product,
be sure to follow the Safety Instructions.
The instructions are divided as ‘WARNING’ and ‘CAUTION’ which mean as follow.
WARNING
CAUTION
The meaning of each symbol in this manual and on your equipment is as follows.
This is the safety alert symbol.
This is the dangerous voltage alert symbol.
After reading the manual, keep it in the place that the user always can
Contact easily.
Before you proceed, be sure to read and become familiar with the safety
precautions at the beginning of this manual. If you have any questions, seek
expert advice before you proceed. Do not proceed if you are unsure of the safety
precautions or any procedure.
WARNING
Be cautious about dealing with CMOS elements of option board.
It can cause malfunction by static electricity.
Connection changing like communication wire change must be done with
power off.
It can cause communication faulty or malfunction.
Be sure to connect exactly between Inverter and option board.
It can cause communication faulty or malfunction.
Check parameter unit when setting parameter.
It can cause communication faulty
This symbol indicates the possibility of death or
serious injury.
This symbol indicates the possibility of injury or
damage to property.
iS7 CC-Link IE Field Manual
2
Introduction
The CC-Link IE Field Master can operate the IS7 drive and monitor the state of IS7 in
the CC-Link IE Field network through the IS7 CC-Link IE Field communication option
board.
SV-IS7 CC-Link IE Field is 1Gbps Ethernet based network. It is not compatible with
CC-Link.
1. Specification of CC-Link IE Field Communication Option Board
Item
Description
Type
Inverter plug-in option, RJ-45 Connection type
Power
From Inverter
Transmission
Speed
1 Gbps
Communication
type
Token passing
Max, number of
stations
120, Heterogeneous connections are possible.
(When used with high-capacity devices, the number of
connections decreases)
Distance
Max. 100m(Twisted pair)
Connection
Branch
No limits.
Topology
Line/Ring/Star topology
Cable
Ethernet cable (IEEE 802.3 1000BASE-T compliant cable
or ANSI/TIA/EIA-568-B(Category 5e) compliant shielded
4-pair branched cable
Connector
Shielded RJ-45
Node
Intelligent device
station
Maximum cycle
size(per node)
RX
32 bit
RY
32 bit
RWr
8 word
RWw
8 word
Transient
transmission
Not available
iS7 CC-Link IE Field Manual
3
2. Product Components
- SV-IS7 CC-Link IE Field communication option board 1 ea
- Screw for fixing on the inverter 2 ea
- SV-IS7 CC-Link IE Field User Manual 1 ea
iS7 CC-Link IE Field Manual
4
3. Installation of the SV-IS7 CC-Link IE Field Option
(1) SV-IS7 CC-Link IE Field Option Module
LINK 1
LINK 2
RUN SD
/RD
DLNK
/ERR LERR
CC-LINK IE Port
CC-LINK IE Port
Screw
Screw
(2) SV-IS7 CC-Link IE Field Option Board Layout
X1
X2
CPU
RJ45 CC-LINK IE Field
connector
RUN
SD/RD
LERR
Inverter
connector
DLNK/ERR
iS7 CC-Link IE Field Manual
5
(3) Mounting the communication option board on SV-IS7 drive
4. Network Connection
Connection terminal of communication cable
Pin No.
Signal
Description
Color
1
TX/RX+
Transmitted/Received data Plus
White/Yellow
2
TX/RX-
Transmitted/Received data Minus
Yellow
3
TX/RX+
Transmitted/Received data Plus
White/Yellow
4
TX/RX-
Transmitted/Received data Minus
Blue
5
TX/RX+
Transmitted/Received data Plus
White/Blue
6
TX/RX-
Transmitted/Received data Minus
Green
7
TX/RX+
Transmitted/Received data Plus
White/Brown
8
TX/RX-
Transmitted/Received data Minus
Brown
CC-Link IE Field
Communication
option board
iS7 CC-Link IE Field Manual
6
(4) Communication Cable Connector
** Wires connected to pin #1 and pin #2 must be twisted.
** Wires connected to pin #3 and pin #6 must be twisted.
Maximum Time-Delay for CC-Link IE Communication
The table below contains the maximum time-delays for each profile that are available
with the CC-Link IE communication option card. The time-delay is the time taken to
process data and return it to the master PLC.
When the master PLC communication cycle time is less (shorter) than the maximum
time-delay, accurate communication from the CC-Link cannot be guaranteed. To
guarantee communication accuracy, the master PLC’s communication cycle time must
be more (longer) than the maximum time-delay.
Mode
Maximum Time-delay for CC-Link
Communication
Profile1
80ms
Profile2
15ms
1
8
1
2
3
4
5
6
7
8
메모 [노태희1]: 추가_131217
iS7 CC-Link IE Field Manual
7
(1) Bandwidth
CC-Link/IE Field communication requires CAT 6a network cables.
(2) Twist- Pair Cable Types
Type
Description
Application
UTP
(U.UTP)
Unshielded high-speed
signal cable
Max. 200MHz
Voice, data and low quality video signals
FTP
(S.UTP)
Single shielded cable
(shielded core only)
*Shield material : Al/plastic complex foil
or copper braid
Max. 100MHz
Electrically stable and protected against EMI
Voice, data and low quality video signals
STP
(S.STP)
Double shielded cable
(shielded pairs and shielded
core)
*Shield material(pair): AL/Plastic
complex foil *Shield material(core):
AL/Plastic complex
Foil or copper braid
Max. 500MHz
Voice, data and video signals
Replaces 75Ωcoaxial cable
iS7 CC-Link IE Field Manual
8
(3) Network Connection
*CC-LINK IE Field Option does not distinguish the directions of LINK1 and
LINK2
Network Type
Configuration
Star topology
Line topology
Ring topology
iS7 CC-Link IE Field Manual
9
5. LED Display
4 green and red LEDs on the CC-Link IE Field communication board displays the
status of CC-Link IE Field communication board. LED is organized as following.
Green
RUN
Green/Red
SD/RD
Red
LERR
Green/Red
DLNK/ERR
LED
Name
Color
Function
RUN
Green
ON –Communication transmitting/receiving
Flickering at the 200ms –Communication
transmitting/receiving is not established
OFF –Check if the Communication cable is connected
correctly or H/W failure
SD
Green
ON –Data transmitting
OFF –Waiting for data transmission
RD
Red
ON –Data receiving
OFF –Waiting for data receive
DLNK
Green
ON –Cyclic data transmitting
OFF –Cyclic data waiting or connection termination
ERR
Red
ON –communication error with PLC/ Lost command
error
OFF –Normal state
LERR
Red
ON –Receive data error or link error
OFF –Normal state
Andere Handbücher für SV-iS7 series
8
Inhaltsverzeichnis
Andere LSIS Gleichstromantrieb Handbücher
LSIS
LSIS SV-iS7 series Bedienungsanleitung
LSIS
LSIS iS7 Series Gebrauchs- und Pflegehandbuch
LSIS
LSIS LSLV-H100 Bedienungsanleitung
LSIS
LSIS S100 Series Bedienungsanleitung
LSIS
LSIS G100 Benutzerhandbuch
LSIS
LSIS SV008iC5-1F Bedienungsanleitung
LSIS
LSIS 004iC5-1 Bedienungsanleitung
LSIS
LSIS Starvert iG5A Series Bedienungsanleitung
LSIS
LSIS S100 Series Bedienungsanleitung
LSIS
LSIS S100 Series Bedienungsanleitung
Beliebte Gleichstromantrieb Handbücher anderer Marken
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Stücklistenhandbuch
Chamberlain Garog
Chamberlain Garog D Series Bedienungsanleitung
Parker
Parker PDS Series Bedienungsanleitung
Festo
Festo DGC G Series Einrichtungshandbuch
Binks
Binks QS-5012-1-CE Bedienungsanleitung
