Lucent Technologies Spirit 308 Bedienungsanleitung

Lucent Technologies

Bell Labs Innovations

SPIRIT®

Communications System

Model 308/616

Customer Installation Instructions

999-500-226

105772578

Issue 4

June 1989

Intellectual property related to this product and registered to AT&T Corporation has been

transferred to Lucent Technologies Incorporated.

Any references within this text to American Telephone and Telegraph Corporation or AT&T

should be interpreted as references to Lucent Technologies Incorporated. The exception is

cross references to books published prior to December 31, 1996, which retain their original

AT&T titles.

Lucent Technologies – formed as a result of AT&T’s planned restructuring – designs,

builds, and delivers a wide range of public and private networks, communication systems

and software, consumer and business telephone systems, and microelectronic components.

The world-renowned Bell Laboratories is the research and development arm for the

company.

INTERFERENCE INFORMATION

FCC REGULATIONS PERTAINING TO THIS EQUIPMENT

NOTICE

Federal Communications Commission (FCC) rules require that you be notified of the following:

FCC (Part 15)

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions in the installation, administration and user manuals

may cause interference to radio and television communications.

This equipment has been tested and found to comply with the limits for a Class A computing

device, pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable

protection against such interference when operated in a commercial environment.

Operation of this equipment in a residential area may cause interference with nearby radios or

television, in which case the owners (at their expense) will be required to take whatever measures

may be necessary to correct the interference.

FCC (Part 68)

This equipment is registered with the Federal Communications Commission (FCC) in accordance

with Part 68 of its Rules. The FCC requires that the manufacturer provides you with the

following information:

1. CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK

The FCC requires that you connect your telephone equipment to the nationwide telephone

network through a standard telephone network interface jack such as a USOC RJ11C.

Registered equipment may not be used with Coin Telephone Lines. Equipment may be used

with Party Lines in areas where state tariffs permit such connections and when equipment is

adaptable for such use.

2. INFORMATION FOR THE TELEPHONE COMPANY

Upon request of your local telephone company, you are required to provide them with the

following information:

A. The lines to which you will connect the telephone equipment.

B. The FCC registration number, AS593M-72132-KF-E, and ringer equivalence number (REN),

0.3A/0.5B. Both numbers are on the controller. The REN is useful to determine how many

devices you may connect to your telephone line and still have them ring when your telephone

line is called. In most, but not all areas, the sum of all REN’s per line should be 5 or less.

You may want to contact your local telephone company for specific information.

The local telephone company must also be notified upon final disconnection of the equipment

from the local telephone company lines.

3. REPAIR INSTRUCTIONS

If it is determined that your telephone equipment is malfunctioning, the FCC requires that it

not be used and that it be unplugged from the modular outlet until the problem has been

corrected. Repairs to this equipment can be made only by the manufacturer or its authorized

agents. For repair procedures, follow the instructions outlined under the AT&T Limited

End User Warranty.

4. RIGHTS OF THE TELEPHONE COMPANY

If telephone equipment is causing harm to the telephone network, the telephone company may

temporarily discontinue your telephone service. If possible, they will notify you before they

interrupt service. If advance notice is not practical, you will be notified as soon as possible.

You will be given the opportunity to correct the problem, and you will be informed of your right

to file a complaint with the FCC.

Your telephone company may make changes in its facilities, equipment, operations, or

procedures that could affect the proper functioning of your equipment. If such changes are

planned, you will be notified.

5. THIS EQUIPMENT IS COMPATIBLE WITH INDUCTIVELY COUPLED HEARING AIDS.

TABLE OF CONTENTS

Introduction

Overview of System

Step 1 Plan Your System

Step 2 Check Outlet Grounding

Step 3 Mount Controller

Mount Controller on Wall

Test the Incoming Telephone Lines

Connect Telephone Lines to Controller

Step 4 Wiring Runs

Business (4-pair) Wiring

Mount Jack Panel Boxes

Run Cable to All Telephone Locations

Install Modular Connecting Blocks

Using Customer Convenience Wiring

Install Plugs

Install Wire Junctions

Secure Telephone Wire

Install Modular Connecting Blocks

Steps 5 InstalI Telephone Sets

Record Installation Date

Desk Mount

Wall Mount

Label Intercom Extension Number

Step 6 Connect System To Wiring Runs

Testing The System

Testing the Incoming Telephone Company Lines

Testing the Wiring Run

Self Test

Controller Test

Telephone Test

Troubleshooting

Optional Accessories

Replacement Parts

NOTICE: While reasonable efforts were made to ensure that the information

in this document was complete and accurate at the time

printing, AT&T

assumes no responsibility for any errors. Changes or corrections to the

information contained in this document may be incorporated into future

re-issues.

Customer Installation Instructions

Introduction

This instruction manual will show you how to install your

SPIRIT

Communications

System. Please read the instructions carefully before beginning installation.

Overview of System

What You Should Find in the Boxes

With the Controller:

controller

three 7’ line cords

system directory label

cord labels

Administration Manual

Customer Installation Instructions

With the Sets:

telephone set

14’ telephone cord

designation labels/plastic strips

User Manual

Reference Card

If your network interface jack has two lines on a single jack you should purchase a 267D

adapter from your AT&T Phone Center store. If you need longer line and telephone cords, you

should purchase them also.

CONTROLLER

CONTROLLER SECTION

Network Interface Jack

WIRING RUN SECTION

TELEPHONE SET SECTION

a jack field installed

near your controller

location

cable extending from

the jack field to each

telephone location

AC Outlet (standard 120 VAC)

jumper cords

plugged into the

jack field and into

the controller

a modular connecting block at

the end of each cable

(telephones will be plugged

in later)

Customer Installation Instructions

Step 1 Plan Your System

Draw a floor plan of your business, showing the location of the network interface jacks,

where your local telephone lines come into the building. You will want to install your

controller close to these jacks.

Show on the floor plan the location of each telephone in your system. Also show the

distances of the cable run from the controller to each telephone location.

Below is a sample floor plan to guide you in making your floor plan.

NOTE: If you need to install SPIRIT Communications System telephones in another building

an in-range, out-of-building (IROB) protection device is required. Contact your AT&T

representative and order part number 31304.

INCOMING TELEPHONE LINES

(also called Network Interface Jacks)

Set 10 30’ Set 14 30’ Set 18 150’

Set 11 40’ Set 15 85’ Set 19 170’

Set 12 50’ Set 16 120’ Set 20 100’

Set 13 60’ Set 17 135’

NOTE: Be sure cords do not cross walkways. Do not run cords

inside or on top of air plenums and ducts or along hot pipes.

Step 2 Check Outlet Grounding

Your

SPIRIT

Communications System control unit has been protected against

AC line and central office line voltage surges caused by lightning strikes or other power

anomalies, provided the system is properly grounded.

Using a circuit tester, check (or have checked by a qualified technician) the outlet into

which your

SPIRIT

system control unit will be plugged. If the circuit tester detects

any of the following faults, have them corrected before installation of the control unit:

— open ground

— open hot

— hot and ground reversed

— reversed polarity

— open neutral

— hot on neutral with hot open

If necessary, have a qualified electrician repair the electrical outlet in the manner

specified by the applicable electrical codes to prevent service interruption and continue

warranty protection. If you have two-wire outlets with no ground wire, a non-switched,

three-wire grounded outlet should be installed.

Customer Installation Instructions

Step 3 Mount Controller

■

Mount Controller on Wall

Choose a location within five feet of the network interface jacks, where the local

telephone company lines enter the building, and near an AC outlet that is not controlled

by a switch. Be sure the controller is in a well-ventilated area with a temperature range

of 40°F to 100°F, and free of excess dust. The controller should be mounted a minimum

of two feet from the floor with the modular connecting blocks positioned at the bottom.

Make a template like the one shown below. Using the template as a guide, install two of

the four screws (not included) in the top, leaving ¼" protruding from wall. Do not install

the bottom two screws until the controller is in place.

Install the controller, placing the two keyholes on the back of the controller against the

screws in the wall and pulling the controller down.

Install the bottom two screws through the tabs on the controller and tighten firmly.

Write the date on one of the date installed (DATE INST:) labels, located on the cord

labels, and place it on the side of the controller.

11 inches

MOUNTING TEMPLATE

7.5 inches

Within 5 feet of

network interface

(where telephone

lines enter build-

ing). Network

intertace may look

different.

CONTROLLER

Jack Field

(Number of apparatus boxes

in field depends on number of telephones).

Within 5 feet

of ac outlet.

(standard 120 VAC)

Customer Installation Instructions

■

Test the Incoming Telephone Lines.

TEST: If you have a standard telephone with a modular cord, plug it into each jack of the

network interface, or incoming telephone lines. If these jacks do not work you will

require service by your local telephone company.

When the telephone lines were installed, the phone number should have been marked on

the network interface jack. If that was not done, write the telephone number on the jack.

You may require help from your local telephone company to decide which jack is for what

number.

Some network interface jacks carry one line only, while some carry two. If your jacks are

one-line jacks (RJ11-type network interface), you may connect the jack directly to the

controller. If your jacks carry two lines (RJ14-type network interface), purchase a 267D

2-line adapter and a D4BU cord.

■

Connect Telephone Lines to Controller.

Remove from the controller box one line cord for each incoming telephone line.

Additional cords and longer cords up to 25’ long may be purchased at a phone store or

from your AT&T representative. LABEL EACH END OF EACH CORD WITH A LINE

CORD LABEL.

If your interface jack is a one-line jack (RJ11 type), plug one end of a line cord into

the “TEL CO LINE” jack for line 1 on the controller and plug the other end into the

network interface jack for line 1. Remove the cord labels from the controller

box and label the line cord with the green cord labels corresponding to the line jack

number. Remove the System Directory Label from the controller box and fill in the

telephone number next to the line number. Repeat the procedure for each line:

If your network interface is a two-line jack (RJ14 type), plug in the 267D 2-line adapter

into the “TEL CO LINE” jack for line 1 on the controller. Plug one end of a line cord

(supplied with the controller) into the “Line 2“ jack of the 267D adapter and plug the

other end into the “TEL CO LINE” jack for line 2 on the controller. Plug one end of

the second D4BU cord into the “PHONE” jack of the 267D adapter and plug the other

end into the network interface jack. Label the D4BU cords with the green line cord

label numbers as shown in the drawing below and write the appropriate telephone

number for each line on the System Directory Label.

Secure the line cords to the wall or baseboard using staples, being careful not to pierce

the cords.

NOTE: If the distance between the controller and the network interface jacks is greater than

7 feet, purchase D4CE extension cords or new D4BU (14’ and 25’ lengths) line cords.

Sample System Directory Label

Controller

123

267D ADAPTER

"PHONE" Line Cord

Labels

"Line 2"

D4BU LINE CORD

Extension

Cord

D4BU LINE CORD

625TD RJ14C

Network Interface

-Marterial Supplied with Controller

-D4BU Line Cord, 7' long: 3 provided

-Labels Line Side: RJ11/14X Network Interface

625TD RJ11C

Network Interface

Customer Installation Instructions

Step 4 Wiring Runs

You may choose to wire your

SPIRIT

Communications System using 4-pair “business”

wiring materials or 2-pair “customer convenience” wiring materials. While the materials

are somewhat different, the procedure for labeling the wiring run is the same.

Each “run” from the controller to a telephone set location should be numbered and

labeled. Materials for labeling the telephone cords are included with the controller.

Do not skip this important step.

If you choose to use the 4-pair “business” wiring materials, the labeling should look

like the following:

Sample System Directory Label

Controller

10 11 12 13

Telephone Cord

Labels

D8W-87

Jumper

Cords Jack Panel box

D4BU Telephone Cord

Jack Panel Wiring

Run Label

Modular

Connecting

Block

25’ Max.

Modjack/Modjack Adapters

Up to 1000’ length

of cable (8-conductor)

Wiring Run

Labels

If you choose to wire your system with customer convenience wiring, use the wiring run

labels to label

EACH END

EVERY

cord, as well as the wire junction boxes.

Note to installers: The SPIRIT system requires a reversal in the station set wiring. This reversal is in the

telephone (tinsel) cord that is packed with the telephone, so all other station set wiring should be straight.

Customer Installation Instructions

Step 4A Business (4-pair) Wiring

You may choose to wire your business with 4-pair “business” wiring to be ready for

future communications systems.

You will need the following materials:

❑

screwdriver (flathead)

❑

scissors

❑

drill and bits appropriate for your walls

❑

You will also need the following kits, available from your AT&T representative.

WIRING INSTALLATION KIT

Wiring run labels

Jack panel box

(Number required depends on

number of telephones. You will

need one jack panel box per six

telephones.) Cable Installation tool

TELEPHONE

LOCATION

CABLE EXTENSION KIT

Telephone location stickers (one per telephone more than 10 feet

from the control unit)

WIRING TERMINATION KIT

(one per telephone)

100-or 200-foot length of cable

(Length depends on distance between

control unit and telephone).

Jumper cord

Modjack-to-modjack adapter

Modular connecting block

Cable clip

Customer Installation Instructions

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lucent Technologies Konferenzsystem Handbücher

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 7.0 Bedienungsanleitung

Lucent Technologies

Lucent Technologies PARTNER Endeavor 362 Kurzanleitung

Lucent Technologies

Lucent Technologies MERLIN Plus Release 2 Bedienungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 7.0 Service-Handbuch

Lucent Technologies

Lucent Technologies PARTNER Advanced Communications System Bedienungsanleitung

Lucent Technologies

Lucent Technologies PARTNER II Release 4.1 Kurzanleitung

Lucent Technologies

Lucent Technologies PARTNER Advanced Communications System Bedienungsanleitung

Lucent Technologies

Lucent Technologies PARTNER Advanced Communications System Release... Kurzanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Benutzerhandbuch

Lucent Technologies

Lucent Technologies PARTNER II Release 4.1 Bedienungsanleitung

Lucent Technologies

Lucent Technologies SPIRIT 2448 Bedienungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 6.1 Benutzerhandbuch

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 7.0 Betriebsanleitung

Lucent Technologies

Lucent Technologies PARTNER Advanced Communications System Release... Bedienungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 7.0 Benutzerhandbuch

Lucent Technologies

Lucent Technologies DEFINITY Guide Bedienungsanleitung

Lucent Technologies

Lucent Technologies Merlin 1030 Bedienungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 6.1 Technisches Handbuch

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 6.1 Montage- und Wartungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 7.0 Technisches Handbuch

Lucent Technologies

Lucent Technologies INDeX 20CC Turret Bedienungsanleitung

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 6.1 Service-Handbuch

Lucent Technologies

Lucent Technologies MERLIN Plus Release 2 Benutzerhandbuch

Lucent Technologies

Lucent Technologies MERLIN LEGEND Release 6.1 Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung