SeaBlaze Typhoon
THROUGH-HULL UNDERWATER LIGHT
1. Locate and mark the desired location of the light. For best performance, SeaBlaze
Typhoon should be mounted 6” to 16” below the waterline. Ideal mounting locations
include transoms, the side and back surfaces of engine brackets and the undersides of
dive platforms. Mounting on a running surface is not recommended.
When selecting a surface, ensure that the light will not interfere with operation of the
engines, trim tabs, rudders etc. and that there is enough room inside the hull for the
threaded housing with additional space to remove the light cartridge. A minimum of 7.5
inches of space from the inside hull surface is recommended. Ensure that the outside of
the hull is at for a minimum of a 4-inch diameter and is free from existing hardware or
holes.
2. Drill a 3-inch hole at the desired installation location. A carbide-tipped hole saw is
recommended to reduce gelcoat chipping. After drilling, clean the outside and inside
surfaces around the hole, removing any debris. For the best seal, the surface should be
smooth and dry.
3. Apply your preferred marine grade sealant to the outside hull surface as well as the
backside of the SeaBlaze Typhoon’s bezel. Extreme care should be taken to thoroughly
coat both surfaces. Dab additional sealant along the side wall of the hole.
4. Feed the wire through the hole and rmly press the SeaBlaze Typhoon into place. From
inside the hull, install the backing washer and then the threaded ring. Tighten the three
bolts provided (7/16” Size Hex, or 11mm) until the backing washer is pressing rmly
into the inside wall of the hull. When fully tightened, sealant should be forced from
all sides of the light on the outside of the hull. Clean off excess and allow the sealant
to cure thoroughly per manufacturer’s instructions prior to returning the vessel to the
water.
Voltage: 10-30vDC
12vDC Amps: 10A
24vDC Amps: 4.5A
Color Temperature: 6500K (White)
Installation Instructions
Limited Warranty
The product is warranted to be free from defects in workmanship and materials for a period of three years from the date of original purchase. Lumitec is not responsible for product
failure caused by abuse, neglect, improper installation, or failure in applications other than those for which it was designed, intended, and marketed. Note that some surface
corrosion is expected when bare metals are used in a marine environment. Corrosion of any metal will be especially aggressive if installation is improper, if bonding is improper or if
stray currents are active in the vicinity of the boat. Lumitec shall not be liable for defects related to such corrosion. Should your Lumitec product prove defective during the warranty
period, promptly notify Lumitec, and return product, freight prepaid. Lumitec will, at its option, repair or replace the product or defective portion without charge for parts or labor, or,
at Lumitec, Inc.’s option, refund purchase price. Products repaired or replaced under this warranty shall be warranted for the unexpired portion of the warranty applying to the original
product(s). No warranty or afrmation of fact, express or implied, other than as set forth in the limited warranty statement above is made or authorized by Lumitec, Inc. Any liability
for consequential and incidental damages is expressly disclaimed. Lumitec liability in all events is limited to, and shall not exceed, the purchase price paid.
Backing WasherHull
Bonding Lug Bolt (x3)
Threaded Ring
Light Operation:
Spectrum: Light will cycle through all available
colors (including white) within the rst 20
seconds. An abrupt OFF/ON toggle of your
standard (SPST) switch will allow the user to
select any discrete color during the cycle. After
20 seconds without interruption, the light will
repeat the full color cycle over a period of 3
minutes – discrete colors can still be chosen
during the 3-minute cycle. The 3-minute cycle
will repeat continuously if left un-interrupted.
You can reset the light at any time by switching
the power off for more than 3 seconds.
Dual-Color (White/Blue): An abrupt OFF/ON
toggle of your standard (SPST) switch allows
the SeaBlaze Typhoon to transition through
each light output mode. 1- Cross-Color Fade
– gently undulating color mix, 2- Blue Only,
3- White Only.
