Lunos e2 neo Bedienungsanleitung
2/65 Ellice Road, Wairau Valley, Auckland 0629
Ph. 09-443 6996
Installaon Instrucons
Installation Instructions
e² 60 Decentralized Ventilation System with Heat Recovery
Safety instructions
Beware: Any assembly work to the ventilation device may only be carried out after disconnecting all phases of supply voltage. The
ventilation device is fitted with protective insulation according to Protection Class II.
Attention: The electric connection may only be made by authorised qualified personnel and according to the applicable version of
VDE 0100.
Attention: This device may not be operated by children and persons (filter replacement/ cleaning) who are not able to operate the
device safely due to their psychical, sensory or mental abilities or their inexperience or lack of knowledge. Children should be supervised
to ensure that they do not play with the device.
Supply Voltage: 230VAC 50Hz
Device Voltage: 12V DC SELV
Protection Rating: IP22
Volume Flow: min. 5m³/h – max. 60m³/h
Sound Power Level: 10 dB - 48 dB
Wiring: KAT6, KAT5e or KNX cables (For SIPS panel house – KAT 6 ISZH, CAT5e ISZH or KNX ISZH)
THE HEATING COMPANY
2
*** Please check for any visual damages for prior installing.
Transformer
24 mm
48 mm
50 mm
48 mm deep
Diameter - 70 mm
Flush Box
52 mm
90 mm
18 W Transformer
60 W Transformer
85 mm
85 mm
Smart Comfort Controller
THE HEATING COMPANY
3
Installation Position:
Lunos e² only functions in pairs in bi-directional operation. The device operates 50 seconds in supply air operation,
the other 50 seconds in exhaust air operation at the set air flow volume. This ensures that the total of the supply air
volume is equal to the exhaust air volume. If a device pair operating in bi-directional operation is installed in two
different rooms of the dwelling, a sufficient interconnection between the air movements must be provided. Undercut
of doors minimum 12mm. In summer the e2 units cycle every hour.
Shipping parts:
Exterior grilles
160mm PVC tube
Heat exchanger
Interior grille
Heat exchanger unit & interior grille
4
THE HEATING COMPANY
Assembly:
Step 1 - Make the wall openings for the assembly tubes (Ø160 mm) by using hole saw bit Ø162 mm. When installing
in timber frame, fix to timber and seal with Proclima grommet (which is supplied) to building wrap or like. Tube to
have slight 3 mm fall to outside. If necessary, shorten the pipe to the required installation length (min. 190mm). Take
care that the tube overlaps on the outside of the cladding as its sits around 5 to 10 mm inside the external
aluminium grilles. The PVC tubes sits flush with the inside of the GIB. (The PVC tube to have a slit cut out on the
inside, to allow cable entry - image on next page).
Electrical Installation, electrical Connection & safety instruction:
Step 2
Transformer can be localized (18W transformer) near the flush box for smart comfort controller (5/SC-FT) or
installed it in the switch board (60W transformer). Install 240 V power cabling to the transformer and then run CAT6
cabling to Controller +ve and -ve. Then run CAT6 cables to each e2 unit (S1, +ve, -ve or S2, +ve, -ve) as below diagram.
Note: Use KAT 6 ISZH, KAT 5e ISZH or KNX ISZH cables for SIPS panel houses.
Make sure that the supply voltages of all circuits are disconnected.
Each electrical circuit of this ventilation system must be fitted with a residual current protection (RCD).
Electrical connections are to be completed only by a qualified electrician.
e2 device 1
e2 device 2
5
THE HEATING COMPANY
Step 3 - connection
For CAT6 cable entry to e2 device
the slit, as per image below, to be minimum 26mm long and 4mm wide. This can be anywhere on the front face as e2
unit can rotate in tube.
Connect cables to plugs, insert pin and socket connectors into the recess of the heat exchanger casing.
NOTE: The violet (purple) wire is always the signal (S1 or S2) connection
Cut out 4 mm
26 mm
Front face flush with GIB
THE HEATING COMPANY
6
Step 4
Interior grilles
or
Rotate inner grill 180° to snap into position. Fit round filter.
9/IBE – Standard interior grille
9/IBS – Sound absorbing interior grille
Interior grille
Press fit into PVC tube
THE HEATING COMPANY
7
Filter Replacement/Cleaning:
Indication by the Event LED illuminating permanently when the filter requires replacing/cleaning. Remove internal
grille, remove filter, insert new or cleaned filter (the filter can be cleaned with dishwashing detergent) re-attach
internal grille.
To reset the filter replacement LED, press and hold the Event button for 3 seconds.
Event LED/
button
NOTES:
THE HEATING COMPANY
7
Filter Replacement/Cleaning
A red LED illuminating permanently when the filter requires replacing/cleaning. Remove internal grille, remove
filter, insert new or cleaned filter (the filter can be cleaned with dishwashing detergent) re-attach internal grille.
To reset the filter replacement LED, rocker the W1 (left switch) one time within 3 seconds. If it is successful the
LEDlights up in RED 3 times to confirm the reset.
NOTES:
Venlaon
Under Tile Heang
In-Concrete Heang
Infrared Ceiling Heang
Panel Heaters
Mirror Demisters
Controllers
Self Levelling Compound
Insulate Mat
www.theheangcompany.co.nz
0800HEATING (432 846)
2/65 Ellice Road, Wairau Valley, Auckland 0629
Ph. 09-443 6996
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Lunos Lüfter Handbücher
Lunos
Lunos Silvento EC Bedienungsanleitung
Lunos
Lunos fgo Bedienungsanleitung
Lunos
Lunos 9/WDS Bedienungsanleitung
Lunos
Lunos Silvento EC Bedienungsanleitung
Lunos
Lunos 9/WDS ABL Bedienungsanleitung
Lunos
Lunos RA 15-60 Bedienungsanleitung
Lunos
Lunos e2 60 Bedienungsanleitung
Lunos
Lunos e2 mini Bedienungsanleitung
Lunos
Lunos Silvento V AC Bedienungsanleitung
Lunos
Lunos AB 30/60 Bedienungsanleitung
Lunos
Lunos RA 15-60 Bedienungsanleitung
Lunos
Lunos Ne t Series Bedienungsanleitung
Lunos
Lunos Silvento EC Bedienungsanleitung
Lunos
Lunos eGO Bedienungsanleitung
Lunos
Lunos ALD Handbuch
Lunos
Lunos AB 30/60 Bedienungsanleitung
Lunos
Lunos 3/UP-BR Handbuch
Lunos
Lunos e2 Series Bedienungsanleitung
Lunos
Lunos Silvento ec Bedienungsanleitung
Lunos
Lunos e2 mini Bedienungsanleitung
