Lutron Electronics RadioRA RA-SBT-CHR Bedienungs- und Sicherheitshinweise

A Step-by-Step Guide for Installion, Programming, and Operation

Note: Please leave this manual with homeowner.

RA-SBT-CHR, RB-SBT-CHR

Setup and Installation Guide For a RadioRA®

ChronosTM System Bridge and Timeclock

READ FIRST

Setup Guide for the RadioRA Chronos System Bridge2

1. It is recommended that only one GRAFIK Eye®Control Unit be wired to each GRAFIK Eye Interface. Multiple GRAFIK Eye

Control Units may be wired (linked) to the same GRAFIK Eye Interface, however, all GRAFIK Eye Control Units on that

link will respond in unison to the commands from the GRAFIK Eye Interface. ALL GRAFIK Eye Control Units wired to the

same Interface will carry out ALL commands from the GRAFIK Eye Interface (i.e. go to GRAFIK Eye scene 3, Turn OFF,

etc...). Interface commands cannot be sent to one individual GRAFIK Eye Control Unit on a link of multiple GRAFIK Eye

Control Units.

• This application may be desired if multiple GRAFIK Eye Control Units are in the same room and it is intended that

the same scene be selected on each GRAFIK Eye Control Unit simultaneously.

• Lutron does not recommend using one GRAFIK Eye Interface to linked GRAFIK Eye Control Units located in more

than one room.

2. Scene 1 on a GRAFIK Eye Control Unit is the default scene for ALL ON, SECURITY, and FLASH MODES. It is recom-

mended that Scene 1 on GRAFIK Eye Control Units be set to full intensity with a fade time of zero seconds.

3. Setting the light levels for GRAFIK Eye scenes should be done prior to any operations in this Setup Guide.

4. A GRAFIK Eye scene may be added to any RadioRA®Master Control button which has been previously programmed

without altering that buttons existing programming.

5. See RadioRA Application Note No.48 (P/N 366-730) for steps to activate GRAFIK Eye scenes 5-16 from a RadioRA

Master Control.

6. For information on integrating your RadioRA system with a photocell, telephone interface, shade motor control, etc... see

the RadioRA Application Notes on our web page at www.lutron.com/applicationnotes/index.html.

7. RadioRA lighting control systems use radio frequency technology for communication. Currently, RadioRA lighting control

systems are available in two frequencies. To determine the frequency of a RadioRA product, examine the model number

on the product’s unit label. The labels are located on the side of all “wallbox” products, and on the bottom of all “tabletop”

products.

The second letter in all RadioRA model numbers indicates the product’s frequency. For example: RA-6D is an “A” fre-

quency product, whereas RB-6D is a “B” frequency product.

Note: Do not mix RadioRA “A” and “B” frequency products within the same system. Products with different frequencies

are not compatible.

If you have any questions concerning the installation or operation of this product, please call the Lutron Technical

Support Center at 1-800-523-9466.

Important Application Notes

System Operation Notes

This guide replaces the Setup Guide (P/N 044-001) included with a system Repeater.

The installer should be aware of the following:

1. In order to install the ChronosTM System Bridge as the Main Repeater in an existing system, all devices in the system must

be returned to their factory defaults prior to installation of the Chronos System Bridge.

2. When using a Whole-home Button on a Master Control, there will be a delay between when the Whole-home Button is

pressed and when the scene activates. The delay will typically be approximately 2 seconds. This applies for scenes that

contain zones of lighting in one system or in both systems. The delay does not apply when the button is activated via

RS-232.

3. For Whole-home Buttons that contain lighting in both System 1 and System 2, the scene will activate one system at a

time, with a delay in between. The delay is typically 3 seconds. The system that the Master Control is in determines which

half of the scene activates first.

4. Only unprogrammed Master Control buttons can be used as Whole-home Buttons. All local programming must be erased

from a Master Control button before it can be assigned as a Whole-home Button.

5. When using Cordless Tabletop Master Controls, the Master Control LEDs will not update when the Master Control is first

awakened from a “sleep” state.

6. When using Master Controls with Raise/Lower buttons with the Chronos System Bridge, the Raise/Lower buttons will not

work on Whole-home scenes.

Setup Guide for the RadioRA Chronos System Bridge 3

FCC Information

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the seperation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment.

This symbol is intended to alert the user to the presence of important installation and operating instructions.

Consumer Information

Danger

This RadioRA®system must not be used to control equipment, other than lighting, which is not visible from every mas-

ter or local control location. It also must not be used to control equipment which could create hazardous situations

such as entrapment if operated accidentally. Examples of equipment which must not be controlled by this RadioRA

system include (but are not limited to) motorized gates, garage doors, industrial doors, and microwave ovens, heating

pads, etc. It is the installer's responsibility to ensure that the equipment, other than lighting, being controlled is visible

from every master or local control location and that only suitable equipment is connected to this RadioRA system.

Using the ChronosTM System Bridge with Older RadioRA®Lighting Zone Controls

On RadioRA Dimmers, Switches, and GRAFIK Eye®Interfaces shipped prior to January 1, 2001, the Legacy setting for fade

times must be used. Raise/Lower functions from Master Controls and the Level Capture feature are also not supported by

these devices shipped prior to January 1, 2001.

Using the Chronos System Bridge with Older RadioRA Master Controls and Interfaces

The Chronos System Bridge Whole-home scenes will not work with Master Controls shipped prior to January 1, 2001. The

buttons on these Master Controls do not send programming necessary to activate the Chronos System Bridge scenes. Also,

this feature was not supported in RA-RS232 and RA-IR Interfaces shipped prior to September 1, 2001. For this reason,

these older devices cannot be used to activate Whole-home scenes.

Using the RA-SCI Switch Closure Interface

The Switch Closure Interface cannot be used to activate Whole-home scenes. The security mode inputs on the Switch

Closure Interface will not work across systems. If a security system is connected to the RA-SCI security inputs, it should be

moved to the security input on the Chronos System Bridge. Refer to Section 6 for instructions on setting up the Chronos

System Bridge contact closure inputs.

Using the RAMC-MFE-WH Security Mode Inputs

The security mode input on the RAMC-MFE-WH will not work across systems. If a security system is connected to the

RAMC-MFE-WH security input, it should be moved to the security input on the Chronos System Bridge. Refer to Section 6

for instructions on setting up the Chronos System Bridge contact closure inputs.

Using Security mode from a RA-RS232 Interface

Security mode activated from an RA-RS232 Interface will not work across systems. If a third-party system is connected to an

existing RA-RS232 Interface, it should be moved to the RS-232 port on the Chronos System Bridge. Refer to Section 5 for

instructions on setting up the Chronos System Bridge RS-232 port.

Compatibility Information

Setup Guide for the RadioRA Chronos System Bridge4

Using This Guide

This guide is divided into sections. Each section deals with a particular feature or set of features of the

ChronosTM System Bridge. Depending on the design of the RadioRA®system and the intended use for the

Chronos System Bridge, some sections may not apply. The figure below shows the sections containing critical

information for each listed feature, in the order that the sections should be read.

Section 1

Getting Started

Section 1

Getting Started

Section 1

Getting Started

Section 1

Getting Started

Section 4

Time Clock

Programming

Section 2

System

Activation

Section 3

Button

Programming

Section 6

Contact Closure

Programming

Section 3

Button

Programming

Section 5

RS-232

Programming

Time Clock

Bridge / Main

Repeater RS-232 Contact Closures

/ Security

Setup Guide for the RadioRA Chronos System Bridge 5

Table of Contents

Section 1 - Getting Started

System Overview

RadioRA System Components ........................................................................................................................7

Chronos System Bridge Features ..................................................................................................................8

System Layout ..................................................................................................................................................9

Chronos System Bridge Hardware Identification..........................................................................................11

Installing the Chronos

Installation ........................................................................................................................................................12

Using the LCD and Buttons ............................................................................................................................15

Using the Keyboard Port..................................................................................................................................16

System Configuration

System Configuration and Features ..............................................................................................................17

Initial Chronos System Bridge Configuration

Setting the Initial Chronos System Bridge Configuration............................................................................18

Section 2 - System Activation

Activating the System

Activate Auxiliary Repeaters............................................................................................................................20

Activate Controls ..............................................................................................................................................22

Section 3 - Button Programming

Button Programming Overview

Local Button Programming Overview ............................................................................................................25

ROOMS and SCENES Overview......................................................................................................................26

Local Buttons, Phantom Buttons, and Whole-home Buttons......................................................................27

Local Button Programming

Assigning a Column of Buttons as ROOMS or SCENES..............................................................................28

Assigning Lighting Zone Controls to Buttons ..............................................................................................30

Setting Light Levels/GRAFIK Eye and GRAFIK RA Scene Selection for Buttons......................................32

Programming the ALL ON and ALL OFF Buttons..........................................................................................34

Advanced Local Programming

Copying Local Button Programming..............................................................................................................36

Erasing Local Button Programming ..............................................................................................................38

Whole-home/Phantom Button Programming

Set Phantom Button Names ............................................................................................................................40

Set Phantom Button Types (ROOM or SCENE) ............................................................................................41

Assigning Lighting Zone Controls to Phantom Buttons ..............................................................................42

Setting Light Levels/GRAFIK Eye Scene Selection for Phantom Buttons..................................................44

Setting Button Properties for Phantom Buttons ..........................................................................................46

Assigning Phantom Buttons to Master Controls ..........................................................................................47

Testing Phantom Button Programming..........................................................................................................48

Erasing Phantom Button Programming ........................................................................................................48

Using the Button Copy Feature

Copying Existing Chronos Programming ......................................................................................................49

Copying Programming from Master Controls to the Chronos System Bridge ..........................................50

Section 4 - Time Clock Programming

Astronomical Time Clock Programming

Setting the Chronos System Bridge Date and Time ....................................................................................52

Creating Time Clock Scenes............................................................................................................................55

Testing Time Clock Scenes..............................................................................................................................59

Erasing Time Clock Scenes ............................................................................................................................60

Setup Guide for the RadioRA Chronos System Bridge6

Table of Contents - Continued

Astronomical Time Clock Programming - Continued

Creating Time Clock Events ............................................................................................................................61

Viewing and Modifying Time Clock Events....................................................................................................63

Deleting a Time Clock Event............................................................................................................................64

Setting the Time Clock Home / Away Mode ..................................................................................................65

Section 5 - RS-232 Programming

RS-232 Port Programming

Overview ............................................................................................................................................................66

Configuring the RS-232 Serial Port ................................................................................................................67

Assigning Zone Numbers ................................................................................................................................68

Assigning Master Control Numbers................................................................................................................70

Phantom Button Programming........................................................................................................................72

Section 6 - Contact Closure Programming

Contact Closure Programming

Setting Up a General Purpose Contact Closure Input for Scene Control ..................................................73

Setting Up a General Purpose Contact Closure Input for Time Clock Mode Control................................76

Setting Up the Security Contact Closure Input..............................................................................................77

Testing Contact Closure Inputs ......................................................................................................................79

Section 7 - User Preferences

Dimmer Locked Presets

Enable Dimmer Locked Presets ......................................................................................................................80

Disable Dimmer Locked Presets ....................................................................................................................82

Asymmetric Fade Rates

Changing Asymmetric Fade Rates..................................................................................................................83

Section 8 - Additional Information

Diagnostic Tools

Viewing the Address Usage and Detecting Missing Devices ......................................................................84

Viewing Device Information ............................................................................................................................86

Using FLASH Mode ..........................................................................................................................................87

Using BEEP Mode ............................................................................................................................................89

Using System BEEP Mode ..............................................................................................................................91

Adding a Switch Closure Input, RS-232, or IR Interface

Activating a Switch Closure Input Interface, RS-232 Interface, or Infrared (IR) Interface ........................92

Returning Components to Default Factory Settings

Master Controls ................................................................................................................................................94

Dimmers ............................................................................................................................................................95

Switches ............................................................................................................................................................96

GRAFIK Eye Interface ......................................................................................................................................97

Repeaters ..........................................................................................................................................................98

Switch Closure Interface..................................................................................................................................99

RS-232 Interface................................................................................................................................................100

IR Interface ........................................................................................................................................................101

Chronos System Bridge ..................................................................................................................................102

Using RadioRA Master Controls with Raise/Lower

Using RadioRA Master Controls with Raise/Lower ......................................................................................103

Glossary

Definitions of Common Terms ........................................................................................................................104

Troubleshooting Guide

Troubleshooting................................................................................................................................................105

Section 1 - Getting Started

Setup Guide for the RadioRA Chronos System Bridge 7

System Overview

RadioRA®System Components

Lighting Zone Controls:

Replace existing switches with

RadioRA Dimmers, Switches, and

GRAFIK Eye®Preset Lighting Controls.

Master Controls:

Master Controls provide control of any

or all RadioRA Lighting Zone Controls.

Dimmer Switch Lamp

Dimmer GRAFIK Eye Preset

Lighting Control

Wall-mounted Master Controls Multi-function Entry Master

Control and Visor Control

Transmitter

Tabletop Master Controls System Interface Master

Controls—RS-232, Switch

Closures, and Infrared (IR)

RF Signal Repeater:

Repeaters provide system setup and

diagnostic functions, and provide an

additional path for communications

between system devices.

Repeater

ChronosTM System Bridge and

Timeclock:

The Chronos System Bridge provides

timeclock capability, RS-232 and

contact closure input interfacing, the

ability to bridge two RadioRA systems,

and acts as a system’s Main Repeater.

Chronos System Bridge

and Timeclock

Setup Guide for the RadioRA Chronos System Bridge8

Section 2 - System Activation

Section 1 - Getting Started

ChronosTM System Bridge Features

System Overview

System Bridge

The Chronos System Bridge bridges two RadioRA®systems for a total of 64 Lighting Zone

Controls and 24 Master Controls.

17 Whole-home Scenes

The Chronos System Bridge provides 17 whole-home scenes which can be accessed via any

button on a Master Control or via the RS-232 connection.

Astronomic Time Clock

The time clock provides an additional 13 whole-home scenes that can be activated by up to

100 programmable time clock events. These events can be scheduled relative to sunrise /

sunset or time of day.

Contact Closure Inputs

One security and two general-purpose contact closure inputs allow interfacing to security and

other third-party systems.

LCD User Interface

The interactive LCD interface guides the user through setting up whole-home scenes, time

clock events, RS-232 device mapping, and other system settings.

Advanced Diagnostics

The Chronos System Bridge provides advanced diagnostics through the LCD, simplifying sys-

tem setup and troubleshooting.

Main Repeater

When bridging two systems, the Chronos System Bridge always acts as the Main Repeater in

both systems. The Chronos System Bridge may also act as the Main Repeater in a single

system.

RS-232 Interface

The RS-232 interface allows for integration with third-party systems.

Setup Guide for the RadioRA Chronos System Bridge 9

Section 1 - Getting Started

System Overview

System Layout

Step 1 Determine if Bridging is Required

Bridging is required if:

• More than 32 Lighting Zone Controls exist, or

• More than 12 Master Controls exist

Step 2 For Bridging Two Systems

For optimal light response time, devices in System 1 and System 2 should not

be used in the same room. Splitting the two systems, as shown below, is

recommended.

Determine location of System 1 and System 2.

Examples:

a. System 1: 1st Floor (see illustration below)

System 2: 2nd Floor

b. System 1: East Wing

System 2: West Wing

c. System 1: Interior

System 2: Exterior

Setup Guide for the RadioRA Chronos System Bridge10

Section 1 - Getting Started

Step 3 Repeater, ChronosTM System Bridge, Lighting Zone Controls,

and Master Control Placement

Place the Chronos System Bridge and Repeaters to provide appropriate RF coverage within

each system.

Repeaters

• Place System 1 Repeaters within 60 feet (18 m) of each other

• Place System 2 Repeaters within 60 feet (18 m) of each other

Chronos System Bridge

• Place the Chronos System Bridge within 60 feet (18 m) of a Repeater in each system

Lighting Zone Controls and Master Controls

• Place System 1 Controls within 30 feet (9 m) of System 1 Repeaters or Chronos System

Bridge

• Place System 2 Controls within 30 feet (9 m) of System 2 Repeaters or Chronos System

Bridge

System Overview

1st Floor View—System 1

60 ft. (18 m)

maximum

30 ft. (9 m) 30 ft. (9 m)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lutron Electronics Steuereinheit Handbücher

Lutron Electronics

Lutron Electronics PowPak RMJ-5R-DV-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless Pico Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Betriebsanleitung

Lutron Electronics

Lutron Electronics RadioRA RAMC-5W Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSGRK-3PCE Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-8E Montage- und Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics QS Timeclock Betriebsanleitung

Lutron Electronics

Lutron Electronics LQR-WPM-6D Betriebsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Montageanleitung

Lutron Electronics

Lutron Electronics GFS-5E Bedienungsanleitung

Lutron Electronics

Lutron Electronics seeTouch guestroom solutions Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK 6000 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Vive PowPak Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Betriebsanleitung

Lutron Electronics

Lutron Electronics QSGRK-6D Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye Architrave GRX-4SLB-DW Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSN-2DALUNV-S Bedienungsanleitung

Lutron Electronics

Lutron Electronics AYFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics PPS-9312 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Stanza SZ-2B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Vive DFCSJ-OEM-OCC Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QS with EcoSystem Betriebsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung