Lutron Electronics Grafik Eye GRX-4000 Series Bedienungsanleitung

Installation, Operation, and Maintenance Manual

DIMMING

PANEL

4000

SERIES

CONTROLS

Overview

GRX-4000 Series Control Unit

GRAFIK Eye GP Lighting Control Panel

HEAT SINK BASE

DIMMERS

FILTER CHOKES

TOP COVER SHIPPED IN BOTTOM OF CRATE –

PUNCH AS NEEDED

CIRCUIT BREAKERS

OUTPUT TERMINAL BLOCKS, NEUTRAL BUS,

AND GROUND (EARTH) BAR

MOUNTING SCREWS

BEZEL

FACEPLATE

FEED

LOAD

AIR VENTS

CONTROL WIRING ENTRY

CIRCUIT SELECTOR

AIR VENTS

Load Wiring Page

Fluorescent Wiring Information ..........................34,35

Neon Application Information ............................36,37

Troubleshooting Guide

Troubleshooting Guide ........................................38

Maintenance

Maintenance ............................................................40

Glossary of Terms

Glossary of Terms....................................................41

Set Up System Page

Save options ............................................................25

16 and 24 zone GRX Control Units .........................26

Control Directory ....................................................27

Circuit Selector Functions, Address,

2Link

™

options ........................................................28

Look Inside a Panel ............................................................Page

GP3 and 4................................................................32

GP8, 12, 16, 20, and 24 ..........................................33

Table of Contents

Install System Page

STEP 1: Mount Wallboxes ..........................................................2

STEP 2: Mount Panels.............................................................2-4

STEP 3: Control Wiring ...........................................................5-7

STEP 4: Feed and Load Wiring ................................................8,9

STEP 5: Set Address Switches ..................................................10

STEP 6: Set Function Switches .................................................11

STEP 7: Install Wallstation ........................................................12

Start Up System

STEP 8: Activate Loads in Bypass.............................................12

STEP 9: Activate Control Units..................................................13

STEP 10: Assign Load Types.......................................................14

STEP 11: Address GRX-4000 Control Units................................15

STEP 12: Remove Bypass Jumpers.............................................16

STEP 13: Check System..............................................................16

Set Up System Page

STEP 14: Assign Primary Zones ......................................................17

STEP 15: Set Up Non Dim Zones ....................................................18

STEP 16: Set Low or High End (optional) ........................................19

STEP 17: Set Normal/Emergency Switch..........................................20

STEP 18: Set Up Scenes on the GRX-4000......................................21

STEP 19: Set Up Wallstation

and Control Interfaces ..................................................22

Reference Sheets

GP8 24

GP3,4

Step-by-Step Instructions

Bel

iev

eit

orn

ot,t

hisi

ssu

ppos

edto

loo

kli

kea

dic

tio

nar

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95.

Bel

iev

eit

orn

ot,t

hisi

ssu

ppos

edto

loo

kli

kea

dic

tio

nar

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95,

und

the

dire

ctio

nof

Dere

kR.

Tho

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95.

Bel

iev

eit

orn

ot,t

hisi

ssu

ppos

edto

loo

kli

kea

dic

tio

nar

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95.

Bel

iev

eit

orn

ot,t

hisi

ssu

ppos

edto

loo

kli

kea

dic

tio

nar

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95.

Bel

iev

eit

orn

ot,t

hisi

ssu

ppos

edto

loo

kli

kea

dic

tio

nar

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95.

und

the

dire

ctio

nof

Dere

kR.

Tho

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95.

Bel

iev

eit

orn

ot,t

hisi

ssu

ppos

edto

loo

kli

kea

dic

tio

nar

Thi

sic

was

cre

ated

byB

rent

Nye

,Jul

,19

95.

Table of Contents for GRAFIK Eye Dimming Panel

SELECTVALUE

VIEWVALUE

SELECTVALUE DISPLAYED

LoadType (See Instructions)

High-EndTrim

CircuitLevel

Low-EndTrim

ZoneAssignment w/ Circuit Schedule

ZoneAssignment w/

ZoneCapture

LinkA

LinkB

Address(Ad displayed)

SELECTCIRCUIT

Circuit

Common

24VFW

MUX

Drain

Sense

1234D5

Value

Comm

Drain

MUX

Link

Step by Step instructions for GRAFIK Eye Dimming Panel

3 5/8"

(92mm) 6 1/4"

(160mm)

1 5/8"

(41mm)

5 1/8"

(130mm)

9 5/8"

(244mm)

19 1/2"

(495mm)

21 1/8"

(537mm)

18"

(457mm)

11"

(279mm)

1 1/8" (29mm)

2 3/4"

(70mm)

1 1/8" (29mm)

2 3/4"

(70mm)

1 3/16" (81mm)

5 1/4"

(130mm)

2 3/4"

(70mm)

5 1/2"

(140mm)

1 1/2"

(38mm)

1 1/2"

(38mm)

STEP 2: Mount Panels

STEP 1: Mount Wallboxes

Use wallboxes with a minimum depth of 2-3/4" (70 mm) for

Wallstations and 3-1/2" (89 mm) for GRX-4000 Series Control

Units.

Multigang installations may require spacers between wallboxes.

Mount wallboxes flush to 1/8" (3 mm) below finished wall surface.

Finished wall should not have gaps around the wallbox of greater

than 1/8" (3 mm).

Mount Wallboxes

and Panels

For More Information . . .

See instructions packaged with each control.

See Installer's video GRX-V-INST, available from Lutron.

Caution! This equipment is air

cooled - vents must not be blocked

or you will void the warranty.

Top View

Bottom View

Left Side Front View Right Side

Suggested control wiring entry

Keyhole accepts a maximum of 1/4" (6mm)

mounting bolt. (#10 (m6) recommended)

Single knockouts are 7/8" (22 mm) dia. Dual

knockouts are 7/8" (22 mm) dia. and 1-1/8" (28 mm) dia.

GP3, 4

(Dimensions and Conduit Entry)

Control

GRX-CIR

GRX-4S-DW

Control Interface

EGRX Controls

GRXSLD

3,4 zone (3 gang)

6,8 zone (4 gang)

GRX-4100/4500

2 zone (2 gang)

3 zone (3 gang)

4-24 zone (4 gang)

All Others (1 gang)

Suggested feed

wiring entry

Suggested load

wiring entry

Control Units

Wallbox

none – use mounting ring (provided)

Lutron # 241-399 (provided)

1900 Box (4"x4" box) or Lutron #241-496

UK Wallbox or Lutron #241-683 (1gang)

Lutron # 241-519 3-1/2" (89 mm) deep

(1 gang each, gangable) or

2-3/4" (70 mm), 3-1/2" (89mm) deep US Wallbox or

Lutron #241-400 2-3/4" (70 mm) deep

(4 gang) or

Lutron #241-703 2-3/4" (70 mm) deep

(4 gang, old work box)

33"

(838mm)

13"

(330mm)

12"

(304mm)

12"

(304mm) 2"

(51mm)

35"

(889mm)

28"

(711mm)

(100mm)

(50mm) 2"

(50mm)

Step by Step Instructions for GRAFIK Eye Dimming Panel 3

STEP 2: Mount Panels (continued)

For More Information . . .

Look inside a GP3 and 4 ..................................32

Look inside a GP8 through 24..........................33

Caution!This equipment is air cooled - vents must not

be blocked or you will void the warranty.

Note: GP8 through 24 must have its top cover punched for Feed

and Load Circuit wiring.

Mount Panels

Top View

Front View

Right SideLeft Side

Bottom View

Keyhole accepts a maximum of 5/16" (8 mm)

mounting bolt (1/4" (m8) recommended).

Class 2/PELV entry knockout is 7/8" dia

. (22 mm)

Suggested feed

wiring entry

Removable top cover is shipped in the same

box as the panel.

Required control

wiring entry

GP8, 12, 16, 20, or 24

Suggested load

wiring entry

GP8 24

GP3,4

For More Information . . .

Look inside a GP3 and 4. ................................32

Look inside a GP8 through 24. ........................33

Step by Step instructions for GRAFIK Eye Dimming Panel

Mount Wallboxes

and Panels

STEP 2: Mount Panels (continued)

GP3, 4

(Suggested Mounting)

Front View Side View Front View Side View

GP8 through 24

(Suggested Mounting)

12" (305 mm)

Minimum

Clearance

to Any

Obstruction

12" (305 mm)

MIN.

Ceiling

Wiring Raceway

Feed

Wiring Load Wiring

Air

Flow

12" (305 mm)

Minimum

Clearance

to Any

Obstruction

Wall Wall

Air

Flow

Notes:

■Panel generates heat. Mount only where ambient temperature will

be 0 °C-40 °C (32 °F-104 °F).

■Reinforce wall structure as required for weight and local codes.

■Panel clearances are 12" (305 mm) above and below and 0" to

each side. (allow room for Class 2/PELV clearance).

■Indoor Use Only. NEMA, Type 1 enclosure, IP2O.

■Relative Humidity < 90% non-condensing.

■GP Panels must be mounted within 7° of true vertical.

Ceiling

Weight w/o Packaging

30 lbs (14kg)

115 lbs (52kg)

130 lbs (59kg)

145 lbs (66kg)

160 lbs (73kg)

175 lbs (80kg)

Panel

GP3,4

GP8

GP12

GP16

GP20

GP24

Max BTUs/Hr.

685

1365

2045

2725

3405

4085

Wiring Raceway

Load

Wiring Feed Wiring

Class 2/PELV wiring

to controls

Class 2/PELV

wiring to controls

Warning! CE marked panels with 10A circuit breakers

are intended for industrial or commercial installations.

Caution! Dimming Panels will hum slightly and

internal relays will click while in operation. Mount where

audible noise is acceptable.

Caution! Mount panel so line (mains) voltage wiring

will be at least 6 feet (1.8 m) from sound or electronic

equipment and its wiring.

Caution! This equipment is air-cooled. Vents must not

be blocked or you will void the warranty.

Air

Flow

Air

Flow

GP8 24

GP3,4

12" (305 mm)

MIN.

Step by Step Instructions for GRAFIK Eye Dimming Panel 5

Wire System

Incorrect: Branch or Home Run not acceptable

PANEL

To other panels, GRX-4000 Series Control Units,

Wallstations, or Control Interfaces.

Control

Interface

GRX-4000

Wallstation

STEP 3: Control Wiring

Control Link Specifications

Questions on wiring?

Lutron may be able to help with charts of Wallstations

versus distance.

Total length of Control Link may be no more than 2,000 feet. This

distance is based on proper shielding on the twisted shielded pair,

and on #12 AWG wire on the wires to terminal 1 and terminal 2 of

the Control Link. If unapproved cable or smaller wire is used, this

limit is affected:

Total number of Wallstations, Control Units, Control Interfaces or

Circuit Selectors = 33 maximum.

Total number of Control Unit addresses = 8 maximum

Note: GRX-4116/4516 has 2 addresses

GRX-4124/4524 has 3 addresses

Total number of Wallstation or Control Interface addresses = 16

maximum.

Notes:

■Make wire connections inside the wallbox and GP panel or in a

junction box (by others) within 8 ft. (2.4 m) of the terminal.

■All control wiring is Class 2/PELV. Do not place any of these

wires in with line voltage (mains voltage) wiring.

■The order of controls within the control wiring is not important.

450 m (1500 ft.)

2000 ft (600 m) maximum

Correct: Daisychain OK

Terminal 1 & 2

Wires Sizes

#12 AWG

#14 AWG

#16 AWG

#18 AWG

Terminal 1 & 2

Wires Sizes

#12 AWG

2.5 mm2

1.0 mm2

GRX-4000

Control

Interface

Wallstation

Max. Control

Link Length

2000 ft. (600 m)

1400 ft. (425 m)

900 ft. (275 m)

600 ft. (180 m)

Max. Control

Link Length

600 m (2000 ft.)

450 m (1500 ft.)

200 m (650 ft.)

Step by Step instructions for GRAFIK Eye Dimming Panel

SELECT CIRCUIT

Circuit

Data A OK Power

1234 5D

Common

24VFW

MUX

Drain

Sense

1234D5

Data B OK

Comm

Drain

MUX

Link

Circuit Selector in the GP Panel

3434

OUT IN

SSA

SSARET

Notes:

■Use the wire connector required by local code (those shown are

common in the USA).

■Connect the Drain/Shield to terminal ‘D’, if this terminal is

available. The Drain is a bare wire – care must be taken so that it

does not touch ground (earth) or wallstation circuitry.

Link A 1-to-1 Wiring (1 to 1, 2 to 2, 3 to 3, . . . )

To additional Control Units, Wallstations,

Panels, or Control Interfaces

GP Panel

STEP 3: Control Wiring (continued)

Control Wiring

To additional Single

Scene Activators

2 # 12 AWG (2.5 mm2)

from terminals 1 to 1,

and 2 to 2

2 # 18 AWG (1.0 mm2) twisted, shielded pair

from terminals 3 to 3, and 4 to 4–Belden

#9461 or Alpha #2211 are recommended

All four wires are available in one cable from Liberty

Cable at 1-800-530-8998. Liberty P/N is Lucom

12/22-RBL

Wallstation GRX-4000 Series Control Unit

SSA Control

(NTGRX-1S)

1 #18 AWG

(1.0 mm2)1 #18 AWG

(1.0 mm2) 5 to

5 (sense for

panel to panel)

1 #18 AWG (1.0 mm

)

1 #18 AWG (1.0 mm2)

Wallstation

Drain/Shield–

Keep short and isolated

2 #12 AWG (2.5 mm2)

1234 5D

Common

24VFW

MUX

Sense

Link A Terminals Drain/Shield

Step by Step Instructions for GRAFIK Eye Dimming Panel 7

SELECT CIRCUIT

Circuit

Data A OK Power

1234 5D

Common

24VFW

MUX

Drain

Sense

1234D5

Data B OK

Comm

Drain

MUX

Link

–2

STAGEBOARD

RECEPTACLE

STEP 3: Control Wiring (continued)

Control Wiring for

DMX

3434

OUT IN

SSA

SSARET

STAGEBOARD

RECEPTACLE

All five wires are available in one cable from Lutron

(P/N GRX-CBL-46L).

To additional Control Units,

Wallstations, Panels, or Control

Interfaces

To panels where Link B

controls circuits. A Lutron

LT1 (Link Terminator)

should be used to terminate

Link B at the last panel. DMX512 Stageboard on Link B

Cable recommended by Stageboard

manufacturer or from Lutron as GRX-CBL-

DMX-250/500.

GRX-4000 Series Control Unit

GP Panel

Circuit Selector in the GP Panel

To next panel

Typical Wiring: DMX to Link B (2Link™only)

Wires must be daisychained and capped off at

both ends of Link B.

DMX Cable Type

Belden 9729/89729:

Lutron GRX-CBL-DMX-250/500:

Common (Pin 1)

DMX+ (Pin 3) DMX– (Pin 2)

Link B as DMX-512

NT-DMJ-IN-WH

Wire

(2) drain/shield

white

black

red

drain/shield

white

black

green

red

From

Circuit Selector

–

No Connect

–

No Connect

DMX Cable Wiring Table

To DMX Jack

(Pin #)

C (1)

+ (3)*

– (2)*

– (4)

+ (5)

C (1)

+ (3)*

– (2)*

– (4)

+ (5)

* Wire in daisy-chain configuration as follows: Cto C, +to +, and –to –.

Link B Wiring (C to C, + to +, – to –)

LT1

8Step by Step instructions for GRAFIK Eye Dimming Panel

Feed and Load Wiring

Temporary Lighting

You do not need to install a temporary distribution panel. Place load

wires into the appropriate terminal blocks.

Each Input Breaker can supply power to a load while the bypass

jumper protects the dimmer from load faults.

Caution!GP panels require entry of wires as specified.

Improper entry will block serviceable parts, and impede

air flow through the panel.

Caution!

Common Neutrals are not permitted.

Run separate Neutrals for each load circuit.

DH HSH

Input circuit breaker

Bypass jumper protects

the dimmer from load

faults.

STEP 4: Feed and Load Wiring (continued)

Feed Wiring (Mains Voltage Wiring)

IMPORTANT!

Panel

GP3 (277 V)

GP3 (120 V, 230 V)

GP4

GP8 through 24 Main Lugs

GP 8 through 24 Main Breaker

Load Circuit Wiring

Panel

GP3, 4

GP8 through 24

Wire Size

1 or 2 #10 AWG - #14 AWG

#6 AWG (10 mm2) - #14 AWG (1.0 mm2)

#10 AWG (4 mm2) - #14 AWG (1.0 mm2)

#2/0 AWG (50 mm2) - #14 AWG (1.0 mm2)

see rating on breaker

Wire Size

#10 AWG (4mm2) - #14 AWG (1.0mm2)

Where to Enter Panel

Bottom Right of Panel (Bottom or Side Entry)

Bottom Right of Panel (Bottom or Side Entry

Top left of Panel (Top entry only)

Where to Enter Panel

Bottom Left of Panel (Bottom or Side Entry)

Top Right of Panel (Top Entry Only)

Andere Handbücher für Grafik Eye GRX-4000 Series

Inhaltsverzeichnis

Andere Lutron Electronics Steuereinheit Handbücher

Lutron Electronics

Lutron Electronics PowPak RMJ-5R-DV-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJ-CCO1-24-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRN-6PCE Betriebsanleitung

Lutron Electronics

Lutron Electronics PPS-9312 Bedienungsanleitung

Lutron Electronics

Lutron Electronics AuroRA ARMC-5T Gebrauchs- und Pflegehandbuch

Lutron Electronics

Lutron Electronics TriPak Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QS with EcoSystem Betriebsanleitung

Lutron Electronics

Lutron Electronics Vive PowPak Bedienungsanleitung

Lutron Electronics

Lutron Electronics Vive DFCSJ-OEM-OCC Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSGRK-3PCE Betriebsanleitung

Lutron Electronics

Lutron Electronics RadioRA RAMC-5W Bedienungsanleitung

Lutron Electronics

Lutron Electronics LQR-WPM-6D Betriebsanleitung

Lutron Electronics

Lutron Electronics QS Timeclock Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-8E Montage- und Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak Energi TriPak Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak FC-SENSOR Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMK-CCO1-24-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJS-16R-DV-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Vive Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless Pico Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics QS Timeclock Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye Architrave GRX-4SLB-DW Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung