Lutron Electronics ODMX-512 Bedienungsanleitung

ODMX-512

DMX512 Input Interface (Class 2 Device) 24 V-100 mA

For Lutron GRAFIK 5000T, GRAFIK 6000R, GRAFIK 7000T,

and LCP128TLighting Control Systems

Installation Instructions

Please Leave for Occupant

Description

The ODMX-512 Interface Control provides an

interface between a DMX512/1990 compatible stage

lighting console (provided by others) and a Lutron

lighting control system. The ODMX-512 will read up

to 32 consecutive DMX512 channel levels (select-

able by DIP switches). The ODMX-512 also contains

terminals that allow an external switch to be used as

an input to the lighting control system.

Important Notes:

1. Read all instructions carefully before starting

installation.

2. Install in accordance with all national and local

electrical codes.

3. Turn power OFF at the control panel BEFORE

installing controls. DO NOT connect high-voltage

power to low-voltage terminals. Improper wiring

can result in personal injury or damage to the

control and other equipment.

4. Check with your local electrical inspector for

compliance with local codes and wiring practices.

Installation

1. Prewiring: The Control Links require special wiring

considerations. Refer to your lighting control system

Installation Guide and/or Lutron job drawings for wir-

ing restrictions that may apply to your speciﬁc project.

2. Turn power OFF to the lighting control system.

!WARNING: Shock Hazard. Always turn off the

power to the control panel before doing any work.

Failure to do so can result in death or serious

personal injury and/or damage to the equipment.

3. Mount the ODMX-512 Interface to a junction box or to

a wall as shown. If the unit is not mounted to a metal

junction box, ensure proper grounding of the metal

casing by connecting a ground wire to the ground

screw. Unscrew and remove the front enclosure cover

to expose the terminal blocks, DIP Switch, and Output

Status LEDs. Insert wires through side knockouts only.

4. Assign Addresses: Address all controls on the

Control Link. Refer to Lutron job drawings for any

preassigned job-speciﬁc address for each control.

Each Control Link can support up to 32 devices. For

proper system operation, each control on a link must

have a unique address. Set DIP Switch SW1, switches

1-5 on each control to select the Link Address (see

Control Link Address Settings on back of sheet).

Record assignments for future reference.

5. Assign DMX 512 channels to read: Using the unit

label as a guide, set DIP Switch (SW2 DMX Zone

Select) on the unit to the desired group of 32 DMX512

channels to read.

6. Strip insulation from wires so 3/8 in. (9.5 mm) of bare

wire is exposed (terminals will accept up to two

#18 AWG (1.0 mm2) wires). If using larger wire, splice

an #18 AWG (1.0 mm2) to the larger wire to make the

connection.

7. Connect Control Link wiring as shown in Typical Control

Link Wiring Diagram. Conﬁrm all connections.

8. Connect external equipment to the DMX512 Input

terminals as shown in the Typical Interface Wiring

Diagram.

9. Replace front enclosure cover. Restore power to the

control panel AFTER the installation of the system is

complete.

MUX LINK

123456

1 2 3 4 5

LUTRON

LED1 LED 2

Output

Status

LEDs

OMX

Control Link

DIP Switch

Control Link

Address

Input from

DMX512

channels

Ground

Screw

CONTR OL LINK

LINK

COM

MU X

1 2 3 4

DMX 512 INPUT

CO M

1 2 3

5 6

EXT SW

DMX 512 INPUT

CO M

1 2 3

1 2 3 4 5

SW1 SW2

DIP Switch

DMX Zone

Select

To External Switch

(by others)

OMX-RS232

3/97 P/N 500-8521 Re vA

INTERFACE CONTROL

SELV (CLASS 2: USA)

COOPERSBURG, PA 18036

ODMX-512

1 2 3 4 5 1 2 3 4 5 1 2 3 4 5

1-32

17-48

33-64

49-80

65-96

81-112

97-128

113-144

129-160

145-176

161-192

177-208

193-224

209-240

225-256

241-272

257-288

273-304

289-320

305-336

321-352

337-368

353-384

369-400

385-416

401-432

417-448

433-464

449-480

465-496

481-512

497-512

1 2 3 4 5 1 2 3 4 5

SW 1 SW 2

Control Link Address

See Instr uction Sheet for Settings

DMX Zone Select

See Belo w

ODMX-512

4 in X 4 in

JUNCTION BOX

INSERT LOW-VOLTAGE

WIRES THROUGH

KNOCK OUTS

ODMX-512

Typical Control Link Wiring Diagram

Wiring Notes:

1. Connection of the control to the Control Link should be made inside the ODMX-512 or in a junction box (provided by

others) located no more than 8 ft (2.5 m) from control.

2. Control link wiring must not be run in the same raceway as line voltage power.

3. Total Control Link length is not to exceed 2000 ft (600 m) unless signal is boosted by a link booster (MX-RPTR).

4. Data cable shield must be maintained throughout the Control Link. DO NOT connect the shield to earth/ground.

5. Refer to your lighting control system Installation Guide and Lutron job drawings for power cable and data cable (Control

Link) wiring restrictions and limitations.

6. Control Link requires a LT-1 (Link Termination Assembly) at each end of the Control Link. Refer to LT-1 instruction sheet for

location and installation information.

• ODMX-512 is one unit load on the DMX512 link as per the

DMX512/1990 and EIA-485 standards.

• Proper DMX512 link wiring practices are required.

• Proper external DMX512 link termination

resistor is needed if the ODMX-512 is at the

end of the DMX512 link.

• Maintained switch closure must be dry or wet

contact closures with:

-On state saturation voltage less than 1.0 V-

-Off state leakage current less than 10 µA

Worldwide Technical and Sales Assistance

If you need assistance, call the toll-free Lutron Hotline:

800.523.9466 (USA, Canada, Caribbean)

Other countries, call 610.282.3800

Fax: 610.282.3090

Lutron will, at its option, repair or replace any unit that is defective in mate-

rials or manufacture within one year after purchase. For warranty service,

call the Lutron Hotline at 800.523.9466 and ask for ﬁeld service. Lutron

shall, at its option, arrange for repair or replacement of any defective unit.

This warranty is in lieu of all other warranties, express or implied,

and the implied warranty of merchantability is limited to one year

from purchase. This warranty does not cover the cost of installa-

tion, removal, or reinstallation, or damage resulting from misuse,

abuse, or damage resulting from improper wiring or installation.

This warranty gives you speciﬁc legal rights, and you may also have other

rights which vary from state to state. Some states do not allow the exclu-

sion or limitation of incidental or consequential damages or limitations on

how long an implied warranty may last, so the above limitations may not

apply to you.

Lutron, the Sunburst logo, and GRAFIK 6000 are registered trademarks and GRAFIK

5000, GRAFIK 7000, and LCP128 are trademarks of Lutron Electronics Co., Inc.

Typical Interface Wiring Diagram Control Link Address Settings

Warranty

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299 USA

Printed in the USA 2/2011 040-378 Rev. A

123456

1 2 3 4 5 6

1: WHITE/BLACK

2: RED

3: YELLOW

4: BLUE

1 Common

2+V

3 MUX

4 MUX

5 Shield

SHIELD

Control

Link

Power

Cable

Data

Cable

1 2 34

MUX LINK

123456

1 2 3 4 5

LUTRON

LED1 LED2

EXT SW

DMX 512 INPUT

COM

1 2 3-

1 2 3 4 5

SW1 SW2

OMX-RS232

3/97 P/N 500-8521 RevA

INTERFACE CONTROL

SELV (CLASS 2:USA)

COOPERSBURG,PA18036

ODMX-512

1 2 3 45 1 2 3 45 1 2 3 45

1-32

17-48

33-64

49-80

65-96

81-112

97-128

113-144

129-160

145-176

161-192

177-208

193-224

209-240

225-256

241-272

257-288

273-304

289-320

305-336

321-352

337-368

353-384

369-400

385-416

401-432

417-448

433-464

449-480

465-496

481-512

497-512

1 2 3 45 1 2 3 45

SW1 SW2

Control Link Address

See Instruction Sheetfor Settings

DMX Zone Select

See Below

Typical Control

(optional)

Control Panel

Control Link

Terminals

Typical ODMX-512 Control

To DMX512/1990

Link

To External Switch

Closure

Last Control on

Control Link

(32 maximum)

LT-1

(Note 6)

Notes 1 & 4 Notes 1 & 4 Notes 1 & 4

LT-1

(Note 6)

To DMX512/1990

Link

COM

+ DATA

– DATA

MUX LINK DMX512 INPUT

123456

To OMX

Control Link

EXT SW

To External

Switch Closure

123

1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5

SWITCH SETTING

DDRESS SWITCH SETTINGADDRESS SWITCH SETTINGADDRESS SWITCH SETTINGADDRESS

SWITCH

UP (ON)

SWITCH

DOWN (OFF)

DIP Switch SW1 settings (switches 1-5)

Inhaltsverzeichnis

Andere Lutron Electronics Aufnahmegeräte Handbücher

Lutron Electronics

Lutron Electronics RadioRA RA-NET-120 Handbuch

Lutron Electronics

Lutron Electronics Grafik Eye GRX-TVI Bedienungsanleitung

Lutron Electronics

Lutron Electronics PAV6M-120 Bedienungsanleitung

Lutron Electronics

Lutron Electronics EcoSystem Bedienungsanleitung

Lutron Electronics

Lutron Electronics VIMCO Sivoia SV-CCI-GRP Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GBO-RS232 Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioRA RA-RS232 Bedienungs- und Sicherheitshinweise

Lutron Electronics

Lutron Electronics RadioRA RA-RC-3 Bedienungsanleitung

Lutron Electronics

Lutron Electronics radioRA GRAFIK Eye RA-GRXI Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSE-CI-DMX Bedienungsanleitung

Lutron Electronics

Lutron Electronics Stanza SZ-CI-PRG Bedienungsanleitung

Lutron Electronics

Lutron Electronics CASETA WIRELESS ELK-M1XSLC Bedienungsanleitung

Lutron Electronics

Lutron Electronics LUT-ELI-3PH Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-CI-PRG Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioTouch RTA-RS232 Bedienungs- und Sicherheitshinweise

Lutron Electronics

Lutron Electronics QSE-CI-DMX Bedienungsanleitung

Lutron Electronics

Lutron Electronics LUT-ELI-3PH Bedienungsanleitung

Lutron Electronics

Lutron Electronics DFC-OEM-DBI Leitfaden

Lutron Electronics

Lutron Electronics RadioTouch RTA-RS232 Bedienungs- und Sicherheitshinweise

Lutron Electronics

Lutron Electronics Grafik Eye GRX-TVI Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSE-CI-NWK-E Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye PB Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch