Lutron Electronics VIMCO Sivoia SV-CCI-GRP Bedienungsanleitung

SV-CCI-GRP

Contact Closure Interface

24V~, Class 2/PELV

MDU TERMINAL BLOCK

1 2 3 4 5 6 7 8

1 - Momentary Raise

2 - Open

3 - Momentary Lower

4 - Close

5 - Preset 1

6 - Preset 2

7 - Preset 3

8 - Preset 4

9 - Common

MDU Pin 1

(Cntrl 1)

MDU Pin 2

(Cntrl 2)

24VAC

Dry Contact

Closure Interface

Class 2

SV-CCI-GRP

Coopersburg, PA USA

Control Wire:

2 conductor

22–24 AWG

Comm

Link

Power

Supply

Motor Drive Unit (MDU)

OUTPUT

INPUT

AC 1

E GND

AC 2

MUX

COM

MUX

CNTRL 2

CNTRL1

Figure A

Description

The Sivoia®Contact Closure Interface (SV-CCI-GRP) con-

trols a user selectable GROUP of shades. This interface

control can be used with devices that have momentary

relay type DRY contact closure outputs. The SV-CCI-GRP

cannot be used with devices providing open collector tran-

sistor outputs. For open collector transistor output devices,

use the SV-GRXI. One SV-CCI-GRP is required for each

GROUP of shades that is to be controlled together. Shade

GROUPS are configured on each Motor Drive Unit (MDU).

One DRY contact closure is required for each control func-

tion (for example: OPEN is one function, CLOSE is another

function). To program the PRESETS, maintain the appropri-

ate closure for a minimum of 4 seconds.

Important Notes

1. Install in accordance with all applicable regulations.

2. Do not connect high voltage power to device.

Improper wiring can result in personal injury or damage

to the device or to other equipment.

3. The SV-CCI-GRP interface is wired to any single MDU

in the group it is controlling.

4. Up to 9 keypads and/or interfaces can be parallel wired

to 1 MDU.

5. Do not connect a contact closure input to more than one

SV-CCI-GRP.

6. The SV-CCI-GRP requires an input closure duration

between 0.1–2 seconds.

Installation

1. Mount the SV-CCI-GRP interface to any indoor surface

using the supplied screws. Mount in a clean, dry location

where temperature will remain between 0°C and 40°C.

Do not mount in an area of excessive moisture.

2. Run the control wire (2 conductor, 22–24AWG) from the

MDU to the SV-CCI-GRP interface. See Figure A.

3. Strip insulation 3/8" from wires.

Note: Closing any contact closure while the shade(s)

are moving will stop the shade(s).

Operation

When a contact closure is selected, the SV-CCI-GRP will

activate the corresponding control function.

Easy Preset Programming

1. Adjust shade(s) to desired position.

2. Close and hold the contact closure for a minimum of 4

seconds. “Pr”will be displayed on all MDU's in that

group indicating the contact closure was programmed.

Note: The Open and Close contact closures can also

be reprogrammed as presets.

Operating Instructions

Please Leave for Occupant

Motorized Shade Systems

shading solutions byVIMCOTM

4. Connect Cntrl 1 on the SV-CCI-GRP to CNTRL1 on the

MDU and Cntrl 2 on the SV-CCI-GRP to CNTRL2 on

the MDU using the 2 conductor control wire

5. Connect each contact closure input with respect to com-

mon as shown below in the wiring diagram.

Problem Causes Remedies

Sivoia®Motor Drive Unit power is OFF.

The SV-CCI-GRP may be wired incorrectly

to the Sivoia Motor Drive Unit.

The closure for the desired PRESET was

held for less than 4 seconds.

The SV-CCI-GRP may be wired incorrectly

to the Sivoia Motor Drive Unit.

Sivoia Motor Drive Unit(s) has its presets

locked out.

The SV-CCI-GRP wires are reversed.

Contact closures inputs do

not operate shade(s).

Presets are not being saved.

Open and Raise closures

close or lower the shade:

Close and Lower closures

open or raise the shade.

Restore power.

Ensure SV-CCI-GRP is wired correctly to the Sivoia

Motor Drive Unit as per the wiring diagram above.

Apply and maintain the contact closure of the desired

PRESET for at least 4 seconds.

Ensure SV-CCI-GRP is wired correctly to the Sivoia

Motor Drive Unit as per the wiring diagram above.

Refer to the Sivoia Motor Drive Unit installation sheet.

Ensure SV-CCI-GRP is wired correctly to the Sivoia

Motor Drive Unit as per the wiring diagram above.

Troubleshooting

VIMCO

11520 Sun Shade Lane

Ashland, VA 23005

Made and printed in the U.S.A. 3/03 P/N 040-165 Rev. C

Technical Assistance

If you need assistance, call the toll-free VIMCO Technical Support

Center. Please provide exact model number when calling.

(800) 446-1503 (U.S.A., Canada, and the Caribbean)

Other countries call (804) 752-3300

Fax (804) 752-3366

Visit our web site at www.vimco.com

Limited Warranty

VIMCO will, at its option, repair or replace any unit that is defective in materials or manufacture

within one year after purchase. For warranty service, return unit to place of purchase or mail to

VIMCO at 11520 Sun Shade Lane, Ashland, VA 23005, postage prepaid.

THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED

WARRANTY OF MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS

WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL, OR REINSTAL-

LATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE RESULTING

FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCI-

DENTAL OR CONSEQUENTIAL DAMAGES. VIMCO'S LIABILITY ON ANY CLAIM FOR DAM-

AGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTAL-

LATION, DELIVERY, USE, REPAIR, OR REPLACEMENT OF THE SHADING SYSTEM SHALL

NEVER EXCEED THE PRICE PAID FOR THE SYSTEM.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state. Some states do not allow the exclusion or limitation of incidental or consequential

damages or limitations on how long an implied warranty may last, so the above limitations may

not apply to you.

This product may be covered under one or more of the following U.S. patents: 5,671,387;

5,848,634; 6,100,659; 6,201,364; 6,313,588; 6,346,781; and corresponding foreign patents. U.S.

and foreign patents pending.

Lutron, Sivoia and the Sunburst logo are registered trademarks of Lutron Electronics Co., Inc.

VIMCO, and shading solutions by VIMCO are trademarks of Virginia Iron & Metal Company, Inc.

shading solutions byVIMCOTM

Andere Lutron Electronics Aufnahmegeräte Handbücher

Lutron Electronics

Lutron Electronics RadioRA RA-NET-120 Handbuch

Lutron Electronics

Lutron Electronics Grafik Eye PB Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioRA RA-RC-3 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GBO-RS232 Bedienungsanleitung

Lutron Electronics

Lutron Electronics CASETA WIRELESS ELK-M1XSLC Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSE-CI-DMX Bedienungsanleitung

Lutron Electronics

Lutron Electronics PAV6M-120 Bedienungsanleitung

Lutron Electronics

Lutron Electronics radioRA GRAFIK Eye RA-GRXI Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSE-CI-DMX Bedienungsanleitung

Lutron Electronics

Lutron Electronics LUT-ELI-3PH Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioTouch RTA-RS232 Bedienungs- und Sicherheitshinweise

Lutron Electronics

Lutron Electronics Grafik Eye GRX-TVI Bedienungsanleitung

Lutron Electronics

Lutron Electronics EcoSystem Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioTouch RTA-RS232 Bedienungs- und Sicherheitshinweise

Lutron Electronics

Lutron Electronics DFC-OEM-DBI Leitfaden

Lutron Electronics

Lutron Electronics Grafik Eye GRX-CI-PRG Bedienungsanleitung

Lutron Electronics

Lutron Electronics ODMX-512 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-TVI Bedienungsanleitung

Lutron Electronics

Lutron Electronics Stanza SZ-CI-PRG Bedienungsanleitung

Lutron Electronics

Lutron Electronics LUT-ELI-3PH Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSE-CI-NWK-E Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioRA RA-RS232 Bedienungs- und Sicherheitshinweise

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch