Lutron Electronics Sivoia QED Roller 64 Bedienungsanleitung

Sivoia QED™

Roller 64™

Pocket Mount

Installation

Instructions

Sivoia QEDTM |Roller 64TM Pocket Mount

Installation Instructions

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions

Tools Required:

Tape Measure 1/4” Hex-Head Driver

Wire Cutter/Stripper Level

Pliers Power Drill

#2 Phillips Screwdriver

Sivoia QED™Roller 64

Shade Brackets with Retaining Screws

(5) Mounting Screws

(#8x1-3/4" (#8x44mm)

Hex Head Screws)

(1) 7 Pin Terminal Block

(1) Programming Stylus

(1) Screwdriver

(1) Pocket

(1) Flap

(2) 4” (102mm) Cable Ties

Notes:

1) Complete wiring and programming information can be found in the Sivoia QED Wire and

Programming Guide, P/N 045-038 or at www.lutron.com.

2) The Electronic Drive Unit (EDU) will need to be powered to complete installation.

Box Contents:

(2) Bracket Leveling Spacer (2) Cable Tie Anchor

(2) Pocket Endcaps (if applicable)

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions 2

Warning: Incorrect installation can lead to severe injury, follow all installation instructions.

Notes:

• The Sivoia QED Roller 64 must be used only with window systems approved by Lutron.

• There must be a clearance of at least 1.3 feet (0.4 meters) between the fully lowered system

and any permanent object.

• Installation shall be executed by a qualified electrician according to national wiring rules.

• Before shade installation, remove any unnecessary cords and disable any equipment not

needed for powered operation. The Sivoia QED Roller 64 has a maximum rated operating

time of 8 min.

• The Sivoia QED Roller 64 must be used only with window systems approved by Lutron,

and should not be taken appart from the window system.

• Codes: Install in accordance with all local and national electrical codes.

• Environment: Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing.

Indoor use only.

Sivoia QEDTM |Roller 64TM Pocket Mount

Installation Instructions (continued)

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions

1Confirm System Dimensions

1.1

System Width System Height

Compare system dimensions on

the package label with the window

dimensions to verify appropriate

window/shade combination.

1.1

Package Label

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions 4

2Install Pocket Endcaps (if applicable)

Slide the 2 tabs of the pocket endcap into the pocket until it is flush with the outside.

2.1

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions 5

3Mount Pocket

Pre-drill pocket to allow clearance for the wires without interfering with the bracket. Follow figure below for suggested

hole locations.

Note: Hole should be large enough to allow adjustment during install without pinching the wire.

Note: Cable should exit from EDU side of the system.

3.1

DANGER - Locate and lock breaker to the shade power supply in the OFF position or

unplug the power plug-in transformer before doing any wiring.

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions 6

3Mount Pocket

Verify mounting surface is level/plumb before attaching pocket.

Note: Pocket may rub fabric if installed with an improper tilt or may cause flap to fall.

Orient the pocket. For regular roller shades, install pocket with flap hanging feature on the opposite side

of the glass. For reverse roller shades, flap hanging feature is on glass side.

3.3

3.2

Flap Hanging

Feature

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions 7

3Mount Pocket (continued)

Mount the pocket using appropriate fasteners (make sure it is level).

Note: Screws must be at least 1.5” (38mm) from system end to avoid interfering with mounting of

shade brackets.

Note: Be sure to pull cable from wall through the hole in pocket while mounting.

Note: The pocket should be mounted to support at least 300 lbs (136 kg). The fasteners provided may

not be appropriate for use in all applications.

Note: Blocks (Not Provided) may be required to prevent fabric from rubbing against trim, window, top

treatment, etc.

3.4

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions 8

4Position the Mounting Brackets

Mark the location of the mounting brackets so they are centered over the window.

Note: Bracket to Bracket Distance = Fabric Width + 1.5” (38mm) = System Width.

4.1

SIVOIA QEDTM Roller 64 Pocket Mount Installation

Instructions 9

5Install the Mounting Brackets

Install the first mounting bracket between the aligning ribs in the pocket.

Aligning Ribs

5.1

Install the second mounting bracket between the aligning ribs in the pocket at the other end of

the system.

Note: Put a screw in the center of each slot. Use slots as needed to ensure brackets are level and

plumb as positioned.

5.2

Andere Handbücher für Sivoia QED Roller 64

Inhaltsverzeichnis

Andere Lutron Electronics Jalousie Handbücher

Lutron Electronics

Lutron Electronics Sivoia QED Betriebsanleitung

Beliebte Jalousie Handbücher anderer Marken

Jysk

Jysk ROGEN Bedienungsanleitung

SOMFY

SOMFY 1241752 Bedienungsanleitung

Rollos

Rollos S-Nanorollo V2 Planungshandbuch

Teptron

Teptron Move Bedienungsanleitung

Renson

Renson Outdoor Loggia Sicherheitsleitfaden

Project Source

Project Source CDLF2342W Bedienungsanleitung

Domondo

Domondo PureNight Installationsanleitung

rollease acmeda

rollease acmeda Easy Spring Air Einrichtungshandbuch

IKEA

IKEA KADRILJ Bedienungsanleitung

Hallis Hudson

Hallis Hudson Rolls Super glide Bedienungsanleitung

Benthin

Benthin P1614 Bedienungsanleitung

MV LINE

MV LINE CLARA 015 Bedienungsanleitung

Current

Current E-WAND Leitfaden

weinor

weinor VertiTex ZipR Handbuch

Roto

Roto ZAR M R4/R7 Bedienungsanleitung

SOMFY

SOMFY Movelite WT Series Bedienungsanleitung

Acmeda

Acmeda RF400 Series Bedienungsanleitung

Motura

Motura Pli_353/3 Bedienungsanleitung