Luxul AMS-4424P Bedienungsanleitung
Simply Connected
Use the AMS-4424P to:
Optimize Streaming Media and HDMI
Over IP Performance
Offer Seamless Network Expansion
Up To 384 Ports
Connect up to 24 PoE-Enabled Devices
(Max Output 250 Watts)
Enhance Performance with Layer 2
and Layer 3 Functionality
Use the AMS-4424P to:
Quick Install Guide
AMS-4424P
AV Series 26-Port Gigabit Stackable
PoE+ L2/L3 Managed Switch
Quick Install Guide
AMS-4424P
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-AMS-4424P 036150505
2
Quick Install Guide
Model Number: AMS-4424P
AV Series 26-Port Gigabit Stackable PoE+ L2/L3 Managed Switch
© 2015 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes to
any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
DOCUMENT CONVENTIONS
These graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CONTACT LUXUL
Sales
P: 801-822-5450
Technical Support
P: 801-822-5450
E: suppor[email protected]
Simply Connected
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
3
PACKAGE CONTENTS
The following items are included in the box:
26-Port Gigabit Stackable PoE+ L2/L3 Managed Switch
Power Cord
Rack Mount Kit
Four rubber pads
Quick Installation Guide
If any of the listed items are missing or damaged, please contact the Distributor
from whom you purchased for return/replacement.
HARDWARE DESCRIPTION
Front Panel
The front panel of the AMS-4424P Switch includes dual colored Link/Activity LEDs
that can be switched from green to blue. In addition, the front panel has Link/
Activity and PoE mode indicators as well as System and Power LEDs.
AMS-4424P Front Panel View
Rear Panel
The rear panel of the AMS-4424P Switch includes 1 console port, 24 Gigabit RJ45
Ports and
2 optical expansion ports that accommodate both 1 Gigabit SFP and 10
Gigabit SFP+ modules (for stacking)
, as well as LED indicators for each port. Each
Gigabit port has one Link/Activity/PoE LED. A push button switch with an LED
indicator switches the display between Link/Activity and PoE.
AMS-4424P Rear Panel View
Quick Install Guide
AMS-4424P
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-AMS-4424P 036150505
4
LED Indicators
Each port has one Link/Activity/PoE LED. A push button switch with LED indicator
switches the display between Link/Activity and PoE.
LED Indicators
LED indicators show the working status of the switch. The following table de-
scribes the LED functionality:
Indicator
Name
Description
System Green Flashing Indicates that the AMS-4424P is running normally.
Green On Booting up or indicates a malfunction. Contact
technical support.
Off Indicates that the AMS-4424P is in startup and initialization
process or is not on.
Power Green On This LED indicates that there is power to the AMS-4424P
Off If LED is off, check the power connection on the back of
the unit.
Speed/PoE
Button
Speed On Port LED’s display Speed status
PoE On Port LED’s display PoE status
Speed Green The Link/Activity LED of the port will be on if there is a
1000Mbps device connected to the port.
Yellow The Link/Activity LED of the port will be on if there is a
10/100Mbps device connected to the port.
Flashing The Link/Activity LED fl ashes when a port is receiving
or transmitting data.
Off There is nothing connected to the port.
Simply Connected
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
5
PoE On Connected device is receiving PoE Power.
Off Connected device is not receiving PoE power.
Green Power being supplied within PD Specified limits
Yellow Power exceeds PD Specified limits
Yellow
Flashing
PoE Fault( i.e. problem with Ethernet cable or PoE device).
At startup, port LEDs will flash for 1 second as a self test.
Rear Panel
AMS-4424P Rear Panel View
Power Input: Please use the included power cable
PREPARING FOR INSTALLATION
System Requirements
Ethernet Cables to connect the AMS-4424P to Ethernet enabled devices
Computer equipped with a Web browser. Supported Web browser versions
include Microsoft I.E. 9.0, Firefox 3.6, Safari 5.0, Chrome 6.0, Opera 10.6 and up.
The Web browser is used to configure the AMS-4424P.
Power must be AC 100-240V~ 3.6A 50/60Hz.
Quick Install Guide
AMS-4424P
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-AMS-4424P 036150505
6
Before Connecting to the Network
The AMS-4424P can be rack-mounted or used as a desktop switch. Before connect-
ing to the network, please be aware of the following requirements:
Install the AMS-4424P in a stable/safe place to avoid any possible damage
Make sure there is space around the AMS-4424P for adequate ventilation and proper
heat dissipation. It is recommended to have at least 4-6 inches around all sides.
Do not place heavy articles on the AMS-4424P.
Power outlets should be within 5 feet of the AMS-4424P.
Verify the ground connection of the outlet is functioning properly.
Check the power cord to confirm a secure connection.
Avoid placement in direct sunlight.
When installing the AMS-4424P on a flat surface, attach the rubber feet to the
bottom of the device to avoid scratching the surface.
AMS-4424P INSTALLATION
Installing the AMS-4424P in a Rack
The AMS-4424P can easily be installed in a standard 19” rack. The AMS-4424P includes
two mounting ears for installing and stabilizing the switch. When attaching the
mounting ears and installing the switch within a rack, please refer to the following
illustration:
Simply Connected
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
7
Rack-Mounting the AMS-4424P
Using the included screws, attach the mounting ears to each side of the switch.
Mount the switch in the rack with the LEDs facing outwards. Be sure the switch is
level and properly secured within the rack.
Desktop Setup
For use as a desktop device, position and apply the included rubber feet to the
bottom of the AMS-4424P.
Quick Install Guide
AMS-4424P
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-AMS-4424P 036150505
8
Attaching the Rubber Feet to the AMS-4424P
Network Connections:
The AMS-4424P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/full-
duplex mode and 1000 Mbps full-duplex mode. All RJ-45 ports support Auto MDI/
MDIX and can be used as ordinary ports or as Uplink ports. Any RJ-45 port can be
used to connect the AMS-4424P to an Ethernet enabled device (including servers,
routers, and other switches) without a crossover cable.
For the RJ-45 ports, Category-5, super Category-5 or Category-6 unshielded twisted
pair (CAT5/CAT5e/CAT6 UTP) should be used.
NOTE: For best results, it is recommended that Category-6 shielded
twisted pair be used to ensure stable data transmission at 1000 Mbps.
The AMS-4424P also offers 2 optical expansion ports that accommodate both 1
Gigabit SFP and 10 Gigabit SFP+ modules (for stacking). Please see below for recom-
mended SFP module and cable options.
Stacking the AMS-4424P
The AMS-4424P support stacking of up to 16 Switches (total of 384 Ports) enabling
you to Manage the stacked Switches in one easy to use interface. Stacking in the
AMS-4424P is Enabled by default and requires an SFP+ (10Gbps) link to be con-
nected between Switches. When connecting more than two Switches there will
be a Master Switch that feeds the other Switches. Stacked Switches automatically
connect to the IP Address of the Master, facilitating Seamless management of the
entire Stack
Simply Connected
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners
9
NOTE: While the AMS-4424P support SFP and SFP+ Adapters only SFP+
Adapters will operate with the Stacking function of the Switch.
Standard SFP (1Gbps) Adapters will result in a normal
switched connection.
Stacking
Stacking the AMS-4424P
One Management Interface for the AMS-4424P
Quick Install Guide
AMS-4424P
14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-AMS-4424P 036150505
10
SFP Cable
Due to the typical mounting proximity of Stacked Switches, Luxul recommends
using an SFP+ Copper Twinax Cable. SFP+ Fiber adapters can also be used and
Luxul recommends Multimode Fiber combined with Multimode capable Fiber
SFP+ adapters for Stacking Switches at distances greater than those supported by
Twinax Cables. Single Mode SFP+ Adapters can be used but must be selected to
conform to the Single Mode Fiber Lines used for interlink and due to the number
of possible options, Luxul has no standard recommendation. We recommend
contacting the Fiber Manufacturer for specifications to obtain the correct Single
Mode adapters requried. The Switch does support SFP Multi Mode and SFP Single
Mode adapters but will not take advantage of the Stacking function when these
modules are used.
Default IP Address
The AMS-4424P default IP address is 192.168.0.4. This address can be changed.
However, for hassle free installation of other plug and play Luxul devices, it is
recommended that the default IP value be maintained.
Login
The AMS-4424P is not equipped with internal DHCP server. However, if your switch
is connected to a Luxul Router, configuration will be automatic. Otherwise, the
IP address of the computer for login and configuration will need to be manually
configured. The table below lists the default parameters of the AMS-4424P.
Parameter: Default Value
Default IP address: 192.168.0.4
Default user name: admin
Default password: admin
Andere Handbücher für AMS-4424P
2
Inhaltsverzeichnis
Andere Luxul Schalten Handbücher
Luxul
Luxul Xen XGS-1008 Bedienungsanleitung
Luxul
Luxul SW-510-48P-F Bedienungsanleitung
Luxul
Luxul XMS-2624P Bedienungsanleitung
Luxul
Luxul AMS-1208P Bedienungsanleitung
Luxul
Luxul XMS-1008P Bedienungsanleitung
Luxul
Luxul XGS-1008P Bedienungsanleitung
Luxul
Luxul AGS-1008M Bedienungsanleitung
Luxul
Luxul XMS-1208P Bedienungsanleitung
Luxul
Luxul XVS-F5 Bedienungsanleitung
Luxul
Luxul XFS-1816P Bedienungsanleitung
Luxul
Luxul Xen XGS-1008 Bedienungsanleitung
Luxul
Luxul Xen XGS-1008 Bedienungsanleitung
Luxul
Luxul AMS-1208P Bedienungsanleitung
Luxul
Luxul AMS-2600 Bedienungsanleitung
Luxul
Luxul AGS-1024 Bedienungsanleitung
Luxul
Luxul AMS-4424P Bedienungsanleitung
Luxul
Luxul XMS-2624P Bedienungsanleitung
Luxul
Luxul XFS-1084P Bedienungsanleitung
Luxul
Luxul XGS-1005 Bedienungsanleitung
Luxul
Luxul XMS-1010P-E Bedienungsanleitung
