Lyman All-American 8 Handbuch

Instruction Guide

for

All-American 8TM Turret Press

VictoryTM Single Stage Press

IdealTM C-Frame Press

BrassSmithTM Powder Measure

All-American 8TM Turret Press

Brass Smith All-American 8 Reloading Press

Overview

Congratulations on your purchase of the Lyman All- American 8 Reloading Press. Please read

over all instructions prior to use.

Parts Diagram

1 Body ................... 7990510

2 Toggle .................. 7726225

3 Link, Straight ............ 7991470

4 Link Pin................. 7726215

5 Link Pin Clip............7726220P

6 Turret ................... 7726160

7 Turret Bushing ........... 7991452

8 Turret Bolt Washer ........ 7991451

9 Turret Bolt ............... 7991450

10 Turret Ball Detent ......... 2990730

11 Turret Ball Detent Spring ... 2990738

12 Turret Handle ............ 7991465

13 Ram .................... 7726230

14 Shell-Holder Clip ......... 7726109

15 Ram Pin................. 7726232

16 Set Screw................ 7726464

17 Handle .................. 7726114

18 Handle Jam Nut........... 7726218

19 Primer Catcher ........... 7726219

Unpacking and Assembly

1. Remove press from packaging, ensure all parts are present.

• Assembled All- American 8 Press (1)

• Handle with knob and jam nut (1)

• Primer Catcher (1)

• Primer Feed body (1)

• 10-32 mounting screws (3)

• Large Brass Primer Tuber with Cotter Pin (1)

• Small Brass Primer Tube with Cotter Pin (1)

• Small Primer Sleeve/Punch with spring.

This is installed in primer feed body from the factory

• Large Primer Sleeve/Punch with spring (1)

• Steel Blast Shield (1)

• 5/32nd Hex wrench (1)

• 1/16th Hex Wrench (1)

• Instruction Manual (1)

• Turret Handle (1)

2. Place press on reloading bench or other flat surface to make assembly easier.

3. Thread handle in toggle and tighten jam nut.

Press set up and use

1. Bolt press firmly to bench.

2. Insert shell holder into the slot at the top of the ram. It will snap into place.

3. Die set up; Follow your die manufacturers set up instructions for your particular die set.

4. To remove turret use a 7/8th socket or insert a screwdriver through hole in turret bolt.

Straight Line Primer Feed set up Instructions

1. Locate Primer Feed Body and three mounting screws. (photo 1)

2. The primer feed body comes with the small primer punch

installed at the factory. If you wish to install the large primer

punch prior to mounting the primer feed body to the press, you

have to unthread the knurled knob, remove spring and pull the

priming arm out of housing. Loosen the small set screw at the

bottom of the punch and remove small primer punch and install

the large primer punch.

3. Reinstall arm through the primer feed body, slide on spring and thread on knurled knob.

4. Place primer feed onto the press body and install the three mounting screws.

5. To load primers into the large or small brass primer tubes follow these steps; all primers to be

loaded into tube must be positioned with the anvil side down and smooth side up.

6. Making sure the cotter pin is installed into the brass primer tube. Take the split end of the

primer tube and place it over a primer and gently push down, the primer will snap into the tube

and hold there. Continue to press primers into the tube until full, approxi-

mately 50 primers.

7. Place the silver collared end of the tube into the primer feed body and

press firmly into housing to seat tube. (photo 2)

8. Remove cotter pin and primers will be ready to feed. Place blast shield

over brass tube and seat into primer feed body. (photo 3)

9. Place spent primer catcher onto press (photo 4)

Using the Straight Line Primer Feed

1. Before you can prime the first case, you will need to load a primer into the

primer punch/cup. Pull back on the knurled knob approximately 3/16ths

of an inch, this will drop a primer into the cup.

2. Lower the press ram until the slot in the ram (just below the shell holder)

is directly in front of the priming arm. Push the priming arm forward and

into the slot. Hold it in this position.

3. Push handle up to lower the ram and seat the primer, then release priming

arm and remove primed shell.

4. You will need to pull the knurled knob back approximately 3/16ths of an

inch each time in order to drop a primer into the primer punch/cup.

NOTE: The priming arm can be used either with the spring assist or without

it.

Maintenance and Troubleshooting

Your Lyman All-American 8 Press has been designed to give you years of trouble free service,

but some preventive maintenance is required.

Before using your press, apply a light film of powdered graphite to the bearing surfaces of all

moving parts. Pay particular attention to the sides of the ram. Thin oil can also be used for this

purpose but powdered graphite is recommended.

To clean your press, use a lightly dampened cloth and wipe the press free of dirt, and contamina-

tion from the press after every use.

Check tightness of turret bolt prior to starting a reloading session, and periodically check during

the reloading session.

Trouble Shooting

Here are some simple troubleshooting tips.

Shell holder loose or falling out.

Make sure shell holder clip is installed on ram.

Handle loose

Make sure handle is threaded completely into toggle and silver jam nut is tight against toggle.

Sticky or Tight Ram

Make sure ram is free of dirt. Use damp cloth to wipe ram, then dry ram and add a thin film

of powdered graphite to the ram.

Inspect ram to insure no spent primers are jammed between ram and press body or linkage.

Remove any spent primers from linkage.

VictoryTM Single Stage Press

Brass Smith Victory Reloading Press

Overview

Congratulations on your purchase of the Lyman Victory Reloading Press. Please read over all

instructions prior to use.

Parts Diagram

1 Body ................... 7726200

2 Toggle .................. 7726225

3 Link, Straight ............ 7991470

4 Link Pin................. 7726215

5 Link Pin Clip............7726220P

6 Ram .................... 7726230

7 Shell-Holder Clip ......... 7726109

8 Ram Pin................. 7726232

9 Set Screw................ 7726464

10 Handle .................. 7726114

11 Handle Jam Nut........... 7726218

12 Primer Catcher ........... 7726219

Unpacking and Assembly

1. Remove press from packaging, ensure all parts are present.

• Assembled Victory Press (1)

• Handle with knob and jam nut (1)

• Primer Catcher (1)

• Primer Feed body (1)

• 10-32 mounting screws (3)

• Large Brass Primer Tube with Cotter Pin (1)

• Small Brass Primer Tube with Cotter Pin (1)

• Steel Blast Shield (1)

• Small Primer Sleeve/Punch with spring.

This is installed in primer feed body from the factory (1)

• Large Primer Sleeve/Punch with spring (1)

• 5/32nd Hex wrench (1)

• 1/16th Hex Wrench (1)

• Instruction Manual (1)

2. Place press on reloading bench or other flat surface to make assembly easier.

3. Thread handle in toggle and tighten jam nut.

Press set up and use

1. Bolt press firmly to bench.

2. Insert shell holder into the slot at the top of the ram. It will snap into place.

3. Die set up; Follow your die manufacturers set up instructions for your particular die set.

Straight Line Primer Feed set up Instructions

1. Locate Primer Feed Body and three mounting screws. (photo 1)

2. The primer feed body comes with the small primer punch

installed at the factory. If you wish to install the large primer

punch prior to mounting the primer feed body to the press, you

have to unthread the knurled knob, remove spring and pull the

priming arm out of housing. Loosen the small set screw at the

bottom of the punch and remove small primer punch and install

the large primer punch.

3. Reinstall arm through the primer feed body, slide on spring and

thread on knurled knob.

4. Place primer feed onto the press body and install the three mounting screws.

5. To load primers into the large or small brass primer tubes follow these steps; all primers to be

loaded into tube must be positioned with the anvil side down and smooth side up.

6. Making sure the cotter pin is installed into the brass primer tube. Take the split end of the

primer tube and place it over a primer and gently push down, the primer will snap into the tube

and hold there. Continue to press primers into the tube until full, approximately 50 primers.

7. Place the silver collared end of the tube into the primer feed body and

press firmly into housing to seat tube. (photo 2)

8. Remove cotter pin and primers will be ready to feed. Place blast shield

over brass tube and seat into primer feed body. (photo 3)

9. Place spent primer catcher onto press (photo 4)

Using the Straight Line Primer Feed

1. Before you can prime the first case, you will need to load a primer into

the primer punch/cup. Pull back on the knurled knob approximately

3/16ths of an inch, this will drop a primer into the cup.

2. Lower the press ram until the slot in the ram (just below the shell holder)

is directly in front of the priming arm. Push the priming arm forward and

into the slot. Hold it in this position.

3. Push the press handle forward to lower the ram and seat the primer, then

raise the ram slightly and release the priming arm. Remove primed shell.

4. You will need to pull the knurled knob back approximately 3/16ths of an

inch each time in order to drop a primer into the primer punch/cup.

NOTE: The priming arm can be used either with the spring assist or without

it.

Maintenance and Troubleshooting

Your Lyman Victory Press has been designed to give you years of trouble

free service, but some preventive maintenance is required.

Before using your press, apply a light film of powdered graphite to the bearing surfaces of all

moving parts. Pay particular attention to the sides of the ram. Thin oil can also be used for this

purpose but powdered graphite is recommended.

To clean your press, use a lightly dampened cloth and wipe the press free of dirt, and contamina-

tion from the press after every use.

Trouble Shooting

Here are some simple troubleshooting tips.

Shell holder loose or falling out.

Make sure shell holder clip is installed on ram.

Handle loose

Make sure handle is threaded completely into toggle and silver jam nut is tight against toggle.

Sticky or Tight Ram

Make sure ram is free of dirt. Use damp cloth to wipe ram, then dry ram and add a thin film

of powdered graphite to the ram.

Inspect ram to insure no spent primers are jammed between ram and press body or linkage.

Remove any spent primers from linkage.

Brass Smith Primer Feed

Parts Diagram

1 Primer Feed Body ......... 7726135

2 Primer Feed Arm.......... 7726139

3 Arm Return Spring ........ 7726141

4 Arm Push Knob........... 7726140

5 Punch Sleeve Spring ....... 7992920

6 Large Punch Sleeve........ 7992918

7 Large Primer Punch ....... 7726130

8 Small Punch Sleeve........ 7992919

9 Small Primer Punch ....... 7726131

10 Punch Set Screw .......... 7726148

11 Mounting Screw .......... 7726147

12 Blast Shield .............. 7726138

13 Primer Tube, Small ........ 7726142

14 Primer Tube, Large ........ 7726143

15 Primer Tube Clip.......... 7726144

16 Blast Shield Adapter ....... 7726136

17 Adapter O-Ring........... 7726137

18 Primer Stop Plunger ....... 7726146

19 Plunger Spring............ 7726145

20 Plunger Set-Screw......... 7994418

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lyman Werkzeuge Handbücher

Lyman

Lyman AccuSight 7031287 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung