M-system R6-NP1 Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 1 / 4

INSTRUCTION MANUAL

PROFIBUS-DP INTERFACE MODULE

(for 62-point analog signals) MODEL R6-NP1

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Network interface module ..................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

■GSD FILE

GSD ﬁles are downloadable at M-System’s web site: http://

www.m-system.co.jp

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT INSERTION/REMOVAL OF MODULES

• It is possible to replace the module with the power is sup-

plied. Be sure to replace it when the module is not com-

municating with a host, as it is possible to affect the sys-

tem. However, replacing multiple modules at once may

greatly change line voltage levels. We recommend that

you replace them one by one.

■GENERAL PRECAUTIONS

• Do not set the DIP switch on the side panel while the

power is supplied. The DIP switch is selectable for main-

tenance without the power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

R6-NP1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 2 / 4

INSTALLATION

Use the Base Model R6x-BSA or R6x-BSB.

Before mounting the Network Interface Module onto the Base, be sure to conﬁgure the module as explained below.

■Station No.

See “COMPONENT IDENTIFICATION.”

Station No. is selectable from 00 to 7D via the front rotary

switches. It is programmed to 7D if a larger number is set

on the switches.

■NETWORK SLOTS ON THE BASE

Mount the Network Module to the dedicated slot on the

base.

• R6x-BSA

The I/O and the power (model: R6x-PF1) modules can be

positioned freely on whichever among the slots 1 through 8.

Set a module address to each I/O module.

123 ・・・ 8

Network

Module

I/O & Power Supply

Modules

• R6x-BSB

The power module (model: R6-PSM) should be located on

the extreme left, the I/O modules can be positioned freely

on whichever among the slots 1 through 8. Set a module

address to each I/O module.

Power Supply

Module

I/O Modules

23 ・・・8

Network

Module

R6-NP1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 3 / 4

COMPONENT IDENTIFICATION

ERR Indicator LED

Configuration Jack

Station No. Setting

Rotary SW, lower digit

Network Connector

Station No. Setting

Rotary SW, upper digit

RUN Indicator LED

■PROFIBUS INTERFACE

PIN NO. SIGNAL SIGNIFICANCE

1 NC Not used

2 NC Not used

3 B_ine Network, B-line

4 RTS RTS signal

5 GND 0V

6 P5V 5V

7 NC Not used

8 A_line Network, A-line

9 NC Not used

■FRONT ROTARY SW

• Station No.: SA1, SA2

Station No. is set in Hexadecimal.

(Setpoint adjustment: 00 – 7D)

■INDICATOR LED

ID S TAT E EXPLANATION

RUN

Green ON Transmitting

Green blinking Data hold

OFF Communication error

Red ON Hardware error

ERR

OFF Normal operating

Transmitting

Green ON/

blinking I/O module error

Red ON No master

Red blinking Address error

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R6CON for detailed operation.

■INTERFACE MODULE SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Card map 1 to 31 1 to 31

R6-NP1

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7792 Rev.2 P. 4 / 4

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

90 (3.54) 5.6

(.22)

90 (3.54) LOCKING CLAMP

POSITIONING GUIDE

18 (.71)

■CONNECTION DIAGRAM

INTERNAL POWER

INTERNAL BUS

CONFIGURATION JACK

JACK

BUS CONNECTOR

PROFIBUS

D-SUB CONNECTOR

I/O DATA DESCRIPTIONS

• 16-bit Analog Data

0 to 100% of the selected I/O range is converted into 0 to 10000 (binary).

With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.

With °F temperature unit, the integer section of raw data is directly converted into the data. For example, 135.4°F is con-

verted into 135.

Negative values are represented in 2’s complements.

015

• Discrete Data

Input 1 (Output 1)

Input 2 (Output 2)

Input 3 (Output 3)

Input 4 (Output 4)

Not Used (Remains “0”)

0 : OFF

1 : ON

015

Andere M-system Steuereinheit Handbücher

M-system

M-system R7ML-EA16 Bedienungsanleitung

M-system

M-system R7C-YS2 Bedienungsanleitung

M-system

M-system R7C-EC8B/UL Bedienungsanleitung

M-system

M-system R7M-YV2-R Bedienungsanleitung

M-system

M-system R7L-RR8 Bedienungsanleitung

M-system

M-system R3-PS3 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7M-YS2 Bedienungsanleitung

M-system

M-system R8-SVT8 Bedienungsanleitung

M-system

M-system R30YS4 Bedienungsanleitung

M-system

M-system R7C-EA16/UL Bedienungsanleitung

M-system

M-system R7D-DA16 Bedienungsanleitung

M-system

M-system M8YC Bedienungsanleitung

M-system

M-system R1D-GH2 Bedienungsanleitung

M-system

M-system R7L-EC8A Bedienungsanleitung

M-system

M-system R7L-EC8A Bedienungsanleitung

M-system

M-system R3Y-SV16 Bedienungsanleitung

M-system

M-system R3-PA8 Bedienungsanleitung

M-system

M-system R7L-DA16 Bedienungsanleitung

M-system

M-system R5-TS Bedienungsanleitung

M-system

M-system M6NPS1 Bedienungsanleitung

M-system

M-system R7M-EC8C Bedienungsanleitung

M-system

M-system R30CT4E Bedienungsanleitung

M-system

M-system R7HL-TS4 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung