M-system M6NPP Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7919 Rev.4 P. 1 / 3

INSTRUCTION MANUAL

PULSE ISOLATOR MODEL M6NPP

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•The equipment must be mounted inside a panel.

•The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

•Install lightning surge protectors for those wires connect-

ed to remote locations.

■POWER INPUT RATING & OPERATIONAL RANGE

•Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 1W

■GENERAL PRECAUTIONS

•Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -20 to +55°C

(-4 to +131°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Body

Front Cover

DIN Rail Adaptor

Specifications

■FRONT VIEW (with the cover open)

Power LED

Input Monitor LED

M6NPP

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7919 Rev.4 P. 2 / 3

INSTALLATION

Set the unit so that its DIN rail adapter is at the bottom. When the unit is installed to an Installation Base (model M6NBS),

refer to its instruction manual.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook at the rear side of unit on the DIN

rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

ADIN Rail

■REMOVING THE UNIT

A)Pull down the DIN rail adaptor using a minus screwdriv-

er.

B)Pull out the lower part of the unit.

C)Remove the upper part from the DIN rail.

DIN Rail Adaptor

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

102 (4.02)

7.5 (.30)

DIN RAIL HOOK

102 (4.02)

[1 (.04)]

8–M3

SCREW TERMINAL

WIRE INSERTION ANGLE

: approx. 35°

SCREWDRIVER

INSERTION ANGLE

: approx. 55°

SCREWDRIVER

INSERTION ANGLE

: approx. 40°

DIN RAIL

35mm wide

5678

1234

• When mounting, no extra space is needed between units.*Screwdriver stem diameter: 6 mm (.24”) or less

M6NPP

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7919 Rev.4 P. 3 / 3

■CONNECTION DIAGRAM

–

OUTPUT

POWER

INPUT

SENSOR EXCITATION

CONNECTOR

POWER

■Mechanical Contact or Open Collector

Input Connection Examples

■Voltage Pulse

+12V

■Open Collector

Output Connection Examples

–

■Voltage Pulse

–

PWR

–

PWR

–

■2-Wire Current Pulse

•External DC Supply

2-WIRE

PICK-UP

–

2-WIRE

PICK-UP

–

DC SUPPLY

–

•Built-in Excitation

200 Ω

+12V

5 kΩ

+12V

200 Ω

+12V

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL unit: mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Solderless terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.2 – 2.5 mm2

3.2 (.13) dia.

4 min.

(.16)

5.8 max.

(.23)

5.5 max.

(.22)

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal

7 – 8 with a multimeter.

3) Input: Check that the input frequency is 30 Hz or less

for relay contact, 100 kHz or less for other types of input.

Check also that input pulse is 10 msec. or wider for relay

contact, 5 µsec. or wider for other types of input.

4) Output: Check that the load resistance meets the de-

scribed speciﬁcations as shown below.

OUTPUT LOAD REQUIREMENTS

Open collector 50 V DC @ 100 mA max.

Voltage pulse 1.0 kΩ min. for 5 V

2.4 kΩ min. for 12 V

4.8 kΩ min. for 24 V

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Andere M-system Prüfgeräte Handbücher

M-system

M-system Mini-M M2TG-14-M2 Bedienungsanleitung

M-system

M-system Mini-M M2MLS Bedienungsanleitung

M-system

M-system Mini-M Series Bedienungsanleitung

M-system

M-system FDY2 Bedienungsanleitung

M-system

M-system AD2LC Bedienungsanleitung

M-system

M-system Mini-M M2PHS2 Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system Mini-M M2PP Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2RS Series Bedienungsanleitung

M-system

M-system M2PA Series Bedienungsanleitung

M-system

M-system FDU Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2MS Series Bedienungsanleitung

M-system

M-system Mini-M M2VV Bedienungsanleitung

M-system

M-system Mini-M M2CDS Bedienungsanleitung

M-system

M-system W2PP Bedienungsanleitung

M-system

M-system Mini-M M2CRS Bedienungsanleitung

M-system

M-system Mini-M M2MST Bedienungsanleitung

M-system

M-system Mini-M Series Bedienungsanleitung

M-system

M-system Mini-M M2PHS Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2VF2 Series Bedienungsanleitung

M-system

M-system Sentronic Mini-M M2XPA3 Series Bedienungsanleitung

M-system

M-system Mini-M M2LMS Bedienungsanleitung

M-system

M-system Mini-M M2AMS2 Bedienungsanleitung

M-system

M-system Sentronic M5DY Series Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung