M-system 27U Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7656-A Rev.3 P. 1 / 2

INSTRUCTION MANUAL

2-WIRE UNIVERSAL TEMPERATURE TRANSMITTER

(PC programmable) MODEL 27U

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

When using this product in potentially explosive atmos-

phere or hazardous (classiﬁed) location, you have to follow

the safety procedure to install it. Please refer to “SAFE IN-

STALLATION MANUAL” for each type of certiﬁcation.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The actual installation environments such as connected

devices and connected wires may affect the protection

level of this unit when it is integrated in a panel system.

The user may have to review the CE requirements in re-

gard to the whole system and employ additional protec-

tive measures to ensure the CE conformity.

■GENERAL PRECAUTIONS

• Before you remove the module, turn off the power supply

and input signal for safety.

■ENVIRONMENT

• When heavy dust or metal particles are present in the air,

install the module inside proper housing with sufﬁcient

ventilation.

• Do not install the module where it is subjected to con-

tinuous vibration. Do not subject the module to physical

impact.

• Environmental temperature must be within -40 to +85°C

(-40 to +185°F) with relative humidity within 0 to 95%

RH in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The module is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required

for satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Specifications

INSTALLATION unit : mm (inch)

This module is suitable for mounting inside a DIN type B

head.

33 (1.30)

2–M4 SCREW

The screws are to be provided by the customer.

27U

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7656-A Rev.3 P. 2 / 2

TERMINAL CONNECTIONS

Connect the module as in the diagram below.

■EXTERNAL DIMENSIONS unit : mm (inch)

44 (1.73) dia.

6.3

(.25)

33 (1.30) 6 (.24) dia.

16.5 (.65)

6–M3 SCREW

2–4.5 (.18) dia.

MTG HOLE

20.7 (.81)

19.5 (.77)

12.7 (.5)

–+

7.6 (.30) dia.

■CONNECTION DIAGRAM

–

LOAD

OUTPUT

24V DC

4 – 20mA DC

INPUT *1

*1. Input Connection Examples

■ DC MILLIVOLT

–

INPUT

■ THERMOCOUPLE

• Single input

–

comp. leadwire

■ RTD & RESISTANCE

• Two-wire

• Three-wire

• Dual input

–

comp. leadwire

+–

• Four-wire

SENSOR 2

SENSOR 1

*2. Limited to 250 – 500Ω when using the communication

to configure the module.

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Input: Check that the input signal is within 0 – 100% of

full-scale.

If the thermocouple / RTD or its extension wires are bro-

ken, the output goes over 100% (below 0% with down-

scale) due to the burnout function. Check leadwires in

such a case.

3) Output: Check that the load is within the permissible

limit including wiring resistance.

Load Resistance (Ω) = Supply Voltage (V) – 9 (V)

0.023 (A)

(including leadwire resistance)

ADJUSTMENT PROCEDURE

To calibrate the signal to match with a receiving instru-

ment or to change the factory-set conﬁgurations, use the PC

Conﬁgurator software installed on a Windows PC via the

Bell202 Modem (model COP-HU).

The PC Conﬁgurator software is downloadable at M-Sys-

tem’s web site: http://www.m-system.co.jp

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Andere M-system Sender Handbücher

M-system

M-system M5XREB Bedienungsanleitung

M-system

M-system M1EXS-2 Bedienungsanleitung

M-system

M-system M5PA-CA-R Bedienungsanleitung

M-system

M-system M6DVF Bedienungsanleitung

M-system

M-system W2CFG Bedienungsanleitung

M-system

M-system M2EXS Bedienungsanleitung

M-system

M-system M3LLC Bedienungsanleitung

M-system

M-system KAC Bedienungsanleitung

M-system

M-system M1EXS-2 Bedienungsanleitung

M-system

M-system W2XT Bedienungsanleitung

M-system

M-system W5PA Bedienungsanleitung

M-system

M-system CTS2 Bedienungsanleitung

M-system

M-system Mini-M M2XUM Bedienungsanleitung

M-system

M-system W2AC Bedienungsanleitung

M-system

M-system M2ADS Bedienungsanleitung

M-system

M-system MXV Bedienungsanleitung

M-system

M-system M2EXV Bedienungsanleitung

M-system

M-system Mini-M M2XU Bedienungsanleitung

M-system

M-system M5PA Bedienungsanleitung

M-system

M-system FSP Bedienungsanleitung

M-system

M-system 6AC Bedienungsanleitung

M-system

M-system M3LM Bedienungsanleitung

M-system

M-system Mini-M M2LCS Bedienungsanleitung

M-system

M-system M5XPA Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung