M-system B5RS Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1518 Rev.4 P. 1 / 2

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

• Install lightning surge protectors for those wires connect-

ed to remote locations.

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -40 to +80°C

(-40 to +176°F) with relative humidity within 0 to 90%

RH in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Span Adj.

Power LED

Zero Adj.

Body

Specifications

INSTALLATION

Set the unit so that its DIN rail adapter is at the bottom.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook at the rear side of unit on the DIN

rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

DIN Rail

■REMOVING THE UNIT

A)Push down the DIN rail adaptor using a minus screw-

driver.

B)Pull out the lower part of the unit.

C)Remove the upper part from the DIN rail.

Spring Loaded

DIN Rail Adaptor

RTD TRANSMITTER MODEL B5RS

B5RS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1518 Rev.4 P. 2 / 2

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the

connection diagram on the front of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

7 8

5 6

3 4

1 2

94 (3.70)

25 (.98) 41 (1.61) [3.3 (.13)]

• When mounting, no extra space is needed between units.

DIN RAIL

35mm wide

8–M3.5 SCREW

7.3 (.29)

3 (.12)

■CONNECTION DIAGRAM

–

MONITOR

–

LOAD

OUTPUT

24V DC

4 – 20mA DC

*DC ammeter’s internal resistance 10 ohms max.

RTD

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Input: Check voltage across the terminal 4 – 3 with a

sensitive voltmeter (With 20°C or 68°F, approx. 70mV

with Pt 100, approx. 35mV with Pt 50Ω).

If RTD wires are broken, the output goes over 100% (be-

low 0% with downscale) due to burnout function. Check

leadwires in such a case.

3) Output: Check that the load is within the permissible

limit including wiring resistance.

Load Resistance (Ω) = Supply Voltage (V) – 12 (V)

0.02 (A)

(including leadwire resistance)

4) When you check the output signal, connect an ammeter

of which the internal resistance is of 10Ω max. to the

monitor terminals.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Andere M-system Sender Handbücher

M-system

M-system Mini-M M2AC Bedienungsanleitung

M-system

M-system W2RS1 Bedienungsanleitung

M-system

M-system M1EXS-2 Bedienungsanleitung

M-system

M-system M5CT-5AM Bedienungsanleitung

M-system

M-system W2XT Bedienungsanleitung

M-system

M-system 10JM Bedienungsanleitung

M-system

M-system W2AC Bedienungsanleitung

M-system

M-system M3SXT Bedienungsanleitung

M-system

M-system M5VS Series Bedienungsanleitung

M-system

M-system Mini-M M2VF Bedienungsanleitung

M-system

M-system 10JFT Bedienungsanleitung

M-system

M-system W5 Series Bedienungsanleitung

M-system

M-system 27TS Bedienungsanleitung

M-system

M-system M3LLC Bedienungsanleitung

M-system

M-system M3LU2 Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system M6SXU Bedienungsanleitung

M-system

M-system SENTRONIC M2SES Bedienungsanleitung

M-system

M-system M2ADS Bedienungsanleitung

M-system

M-system Mini-M M2E Series Bedienungsanleitung

M-system

M-system F2SP Bedienungsanleitung

M-system

M-system 27U Bedienungsanleitung

M-system

M-system M5XWTU Bedienungsanleitung

M-system

M-system Mini-M M2TG Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung