M-system MFS2 Bedienungsanleitung
MFS2
P. 1 / 3EM-1383
SPLIT-RANGE TRANSMITTER
(isolated four outputs) MODEL MFS2
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■ PACKAGE INCLUDES:
Signal conditioner (body + base socket + input resistor)
..... (1)
Input resistor is provided only with current input type.
■ MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
This unit is factory adjusted and calibrated according to the
Ordering Information included in the product package.
The MFS2 is programmable using the PC Configurator
Software. For detailed information on the PC configuration,
refer to the MFS2CFG users manual. The MFS2CFG PC
Configurator Software is downloadable at M-System’s web
site: http://www.m-system.co.jp.
POINTS OF CAUTION
■ POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
85 – 264V AC rating: 85 – 264V, 47 – 66 Hz, approx. 3 – 4VA
24V DC rating: Rating ±10%, approx. 2W
110V DC rating: 85 – 150V, approx. 2W
■ UNPLUGGING THE UNIT
• Before you remove the unit from its base socket or mount
it, turn off the power supply and input signal for safety.
■ ENVIRONMENT
• Indoor use
• When heavy dust or metal particles are present in the air,
install the unit inside proper housing with sufficient ven-
tilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within 0 to 50°C
(32 to 122°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■ WIRING
• Do not install cables (power supply, input and output)
close to noise sources (relay drive cable, high frequency
line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■ AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
COMPONENT IDENTIFICATION
■ HOW TO OPEN THE FRONT COVER
Position your finger on the hook at the top of front cover
and pull.
■ FRONT VIEW
Body Base Socket
Connection Diagram
Front Cover
Specifications
The shape of base socket may be different
for some models.
Input Resistor
PC Configurator Jack
Power LED
MFS2
P. 2 / 3EM-1383
INSTALLATION
Detach the yellow clamps located at the top and bottom of
the unit to separate the body from the base socket.
■ DIN RAIL MOUNTING
Set the base socket so that its
DIN rail adaptor is at the bot-
tom. Position the upper hook
at the rear side of base socket
on the DIN rail and push in
the lower. When removing
the socket, push down the
DIN rail adaptor utilizing a
minus screwdriver and pull.
■ WALL MOUNTING
Refer to “EXTERNAL DI-
MENSIONS.”
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the con-
nection diagram on the side of the module.
When an input resistor is provided with the module, attach
it together with input wiring to the input screw terminals.
Clamp
(top & bottom)
DIN Rail
35mm wide
Spring Loaded
DIN Rail Adaptor
Shape and size of the base socket
are slightly different with various
socket types.
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Power input voltage: Check voltage across the terminal
7 – 14 with a multimeter.
3) Input: Check that the input signal is within 0 – 100% of
the full-scale.
4) Output: Check that the load resistance meets the de-
scribed specifications.
5) Split-range setting: Confirm that the transmitter out-
puts are provided as intended.
MAINTENANCE
Regular calibration procedure is explained below:
■ CALIBRATION
Warm up the unit for at least 10 minutes. Apply 0%, 25%,
50%, 75% and 100% input signal. Check that the output
signal for the respective input signal remains within accu-
racy described in the data sheet. When the output is out of
tolerance, recalibrate the unit using the PC Configurator
Software (moodel: MFS2CFG).
*Input shunt resistor attached for current input.
CONFIGURATOR JACK +
–
OUTPUT 3
9
15
+
–
OUTPUT 2
10
1
+
–
OUTPUT 1
11
2
+
–
OUTPUT 4
8
3
U(+)
V(–)
POWER
7
14
+
–
*
ANALOG INPUT
4
R
12
5
6
CONTACT INPUT
MFS2
P. 3 / 3EM-1383
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
80 (3.15)
72 (2.83) 109 (4.29)
139 (5.47) [3.3 (.13)]
20
(.79)
35.4 (1.39)
CLAMP
(top & bottom)
DIN RAIL
35mm wide
80 (3.15)
60 (2.36)
72 (2.83)
7.8 (.31)
2–4.5 (.18) dia.
MTG HOLE
25 (.98) deep
14–M3.5
SCREW
• When mounting, no extra space is needed between units.
• Input shunt resistor attached for current input.
56
14
11
1
1015
3
2
7
9
8
12 (.47)
INPUT RESISTOR
(model: REM)
12
4
Andere M-system Sender Handbücher
M-system
M-system W5MS Bedienungsanleitung
M-system
M-system M3SXR Bedienungsanleitung
M-system
M-system KCEC Bedienungsanleitung
M-system
M-system M6SVS Bedienungsanleitung
M-system
M-system 10JM Bedienungsanleitung
M-system
M-system W2XR Bedienungsanleitung
M-system
M-system M3LT Bedienungsanleitung
M-system
M-system W2TS Bedienungsanleitung
M-system
M-system M5PT Bedienungsanleitung
M-system
M-system 10VF Bedienungsanleitung
M-system
M-system Mini-M M2REB Bedienungsanleitung
M-system
M-system Mini-M M2XRP2 Bedienungsanleitung
M-system
M-system W5 Series Bedienungsanleitung
M-system
M-system Mini-M M2XU Bedienungsanleitung
M-system
M-system BVS Bedienungsanleitung
M-system
M-system M2XPA2 Bedienungsanleitung
M-system
M-system W2VABS Bedienungsanleitung
M-system
M-system MFS2 Bedienungsanleitung
M-system
M-system M3SXV Bedienungsanleitung
M-system
M-system 6BLC Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
