M2 Antenna Systems 8-30LP9 Bedienungsanleitung

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.00

Model .........................................8-30LP9

Frequency Range.......................8 To 30 MHz

*Gain ..........................................9.5 dBi @ 70’ OG

Front to back ..............................12 dB

Feed Impedance........................50 Ohms Unbalanced

Maximum VSWR........................1.9:1

Input Connector..........................SO-239, “N” Female avl.

Power Handling..........................3 Kw, Higher avl.

Boom Length / Dia......................48’ X 3” X 0.125 wall

Maximum Element Length..........50’

Turning Radius:..........................36’

Wind area / Survival...................18 Sq. Ft. / 125 MPH

Weight / Ship Wt.........................170 lbs. / 190 lbs.

M2 Antenna Systems, Inc.

Model No: 8-30LP9

FEATURES:

This special hybrid log periodic is a rugged versatile performer designed for years of trouble free service. Ma-

chined aluminum element to boom clamps and solid fiberglass rod center insulators are just a few of the

unique structural features in this remarkable antenna. The 8-30LP9 is a single antenna system that matches

up with today’s modern solid state equipment.

Maritime, Government, Commercial, MARS and Scientific users will find that the 8-30LP9 reliably fills a variety

of communication requirements. When properly installed at 65 feet or higher this nine element antenna is a

world wide, world-class performer. Solid electrical and structural design will maintain communications when

other antennas have long since faded into the noise.

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd* (OG = Over Ground)

BEFORE YOU BEGIN: Look over the DETAIL DRAWINGS, ELEMENT ASSEMBLY AND

DIMENSION SHEET, to get familiar with the various parts of the log periodic. Tools handy for

assembly process: Phillips screwdriver, 11/32, 7/16, 1/2, & 9/16” nut drivers, end wrenches and/or

sockets, measuring tape.

Two containers of zinc paste (Penetrox, Noalox, or equiv.) have been provided to enhance and

maintain the quality of all electrical junctions on this antenna. Apply a thin coat wherever two

pieces of aluminum come in contact or any other electrical connections are made. We also

recommend dabbing the end threads the bolts and screws with the zinc paste just before you

install them. This adds long term protection to the hardware, reduces friction and lets you get

each bolt or screw tighter on the first tightening.

1. ASSEMBLING ELEMENT #1, 2 & 3 MOUNTING PLATES. See the “DETAIL, ELEMENT #1,2

AND #3” drawing. The back three large elements will mount on the four inch boom. This requires

6” x 6” x 1/4” flat plates. 1-1/4” saddles hold the 1-1/4” diameter fiberglass rod center insulators

and the plates mount on the boom with 4” saddles. Element #1 and 2 have 3/4” vertical support

risers. Element #3 does not. The center insulator is 1-1/4” diameter. Push on two 1-1/4” poly rings

and center them at just over 6” apart. Set this assembly on the 1-1/4 aluminum saddles and add

the top saddles. Hardware for this whole assembly is shown on the drawing. Continue adding all

the parts shown on the drawing except the elements and the phasing line parts

The disc insulators are sometimes a very tight fit on the rods. If so, place them in hot water

a few moments before installation.

2. ELEMENT #4 MOUNTING PLATES. The two 3 x 6 x 1/2” plates milled with a .5” radius channel

are for ELEMENT #4. LOCATE THE 1’ diameter fiberglass rod and slide on two 1” poly rings and

center them just over 6” apart. Clamp this assembly between the two plates. Align the holes in the

fiberglass vertical and tighten the hardware. This element attaches to the boom with two 3”

saddles. Center the rod and tighten the hardware EVENLY, so the plates are parallel and the

same amount of threads are showing through all the locknuts.

8-30LP9 ASSEMBLY MANUAL

ELEMENT MOUNTS, #5 THROUGH 8

3. ELEMENT #5 MOUNTING PLATES. Element #5 uses two 2-1/2 x 4” plates and TWO SADDLES

to attach it to the boom. A 7/8” diameter fiberglass rod gets two 7/8” I.D. poly rings pushed on and

centered just over 4” apart. Align the holes vertical and tighten the hardware.

4. Elements #6 through #8 use a single 2-1/2 x 4 x 3/8” plate and a matching rectangular 1-1/2 x 4 x

1/4” clamp plate. The 7/8 x 29-3/4 inch long fiberglass rods each need 7/8“ poly rings installed and

centered just over 4“ apart. Clamp these assemblies between the plates, aligning the holes vertical

and tighten the hardware. (Elements #6, 7 and 8 each use a single 3” bottom cradle).

Note: Element #8 is the feed point and a BALUN BRACKET is added to the clamp plate assembly

5. Element #9, the front DIRECTOR element mounts differently, using two 3” machined cradles back

to back. It is grounded to the boom. A 7/8” x 30 “ sleeve couples the two 3/4” element halves together

with the same bolts that hold the bottom saddles. Assemble loosely at this time.

LOG PERIODIC ELEMENT ASSEMBLY

1. REFER TO “ELEMENT ASSEMBLY” SHEET

2. Start with the smallest elements. Elements #8, #7, #6 and #5 are similar. There are two halves to

each element. Do the following for both halves. Locate and install a 1” hole, ELEMENT CLAMP

BLOCK 1/4” from the butt end of a 1” x 48” section. Use an 8-32 x 1-1/2” screw and locknut. Orient

the clamp block so its upper hole is aligned with the hole in the butt of the tube. Locate a small

clamp plate and attach it loosely to the inside of the element clamp block using a 1/4-20 x 1” flat

head bolt and locknut. Now add the 3/4” section on element #8 and secure using 8-32 hardware

shown on the drawing. Finally, slide each element half over the center 7/8” fiberglass rod insulator

assembly and secure with 1/4-20 x 1-1/2” bolts and locknuts. When element #8 is complete, set it

aside and continue finalizing elements 7, 6, & 5.

8-30LP9 ASSEMBLY MANUAL

NOTE: THE FOLLOWING ELEMENTS HAVE SLEEVED SECTIONS. MOST ARE IN PLACE FROM

THE FACTORY BUT IF NOT, WIPE THE SLEEVE CAREFULLY AND LUBE LIGHTLY WITH OIL

OR W4-40 PRIOR TO INSERTION. IF THE SLEEVE STICKS OR BINDS AT ALL, STOP, STOP

STOP. DO NOT GO FURTHER, REMOVE CAREFULLY AND CLEAN AGAIN. IT MAY ALSO BE

NECESSARY TO PUSH A CLEAN CLOTH THROUGH THE ELEMENT BEFORE TRYING THE

INSERTION AGAIN. AT THE FACTORY, WE HAVE FOUND THAT WD-40 IS THE BEST AT

LOOSENING THE BIND BETWEEN TWO SECTIONS OF ALUMINUM TUBING.

3. Element #4 is next. Again place an element clamp block with a 1-1/4” hole at 1/4” from the butt of

the element. Align with element hole as before and secure using an 8-32 x 1-3/4 screw and

locknut. Add the small clamp block and 1/4-20 x 1” flat head bolt and locknut loosely. If it is not

already there, insert a 1-1/8 x 20” sleeve in the butt of the element and hold in place temporarily

with a 1/4-20 x 1-3/4” bolt and locknut but don’t tighten yet. Continue adding the 1”, 3/4 and 1/2”

sections securing with the 8-32 hardware listed on the drawing. Tighten each joint securely so no

wiggle is felt when moving the element. Finally, remove the 1/4-20 x 1-3/4 bolts and slide each

element half on the dual saddle center insulator assembly. Re-install the bolts and tighten.

8-30LP9 ASSEMBLY MANUAL

8-30LP9 DIMENSION SHEET

8-30LP9 ELEMENT ASSEMBLY

4. Element #3 is has 3 internal sleeves as noted on the ELEMENT ASSEMBLY drawing. Again start

at the butt and insert the 1-3/8 x 25” sleeve and hold in place with a 1/4-20 x 2” bolt and locknut

but don’t tighten. Next, install an element clamp block 1/4” in from the end. Secure with 8-32 x 2”

screw and locknut, align with the element hole and tighten. Add the small clamp block and secure

as before. Now insert ( if not already in) the 1-1/8” x 35” inner sleeve into the butt of the 1-1/4”

section and attach to the 1-1/2” section. Continue assembling the rest of the element. Tighten all

element hardware. Finally remove the 1/4-20 x 2” bolts and install the element halves on the

center insulator assembly. Re-install the bolts and tighten.

5. Element #2 has an outer 1-5/8 x 27” sleeve and an inner 1-3/8 x 85” sleeve. The inner sleeve

should already be in place from the factory. Slide on the outer sleeve and hold in place using

another 1/4-20 x 2” bolt and locknut but don’t tighten. Next slip on another ELEMENT CLAMP

BLOCK with a 1-1/2” hole. Note that the very end of the element is still 1-1/2” O.D. secure the

clamp at 1/4” from the butt end of the element and secure with 8-32 x 2” screw and locknut

aligning as before. Add the small clamp block and secure loosely with another 1/-20 x 1” flat head

bolt and locknut. As you insert the next 1-1/4” section, note that it goes in 5” instead of the normal

3”. This is so it can couple with the last inch or so of 1-3/8” sleeve inside the 1-1/2” section. This

overlap is extremely important to maintain the overall strength of the element in this joint. Continue

assembling the rest of the element. Tighten all element hardware. Finally, remove the bolts and

slip each element half on the center insulator assembly. Re-install the bolts and tighten.

Now install the two 1/4” eyebolts. Install a thimble or cable eye in each eyebolt and attach a 166”

length of HPTG-1200 and secure with two clips. Repeat for the other element half. Open the 5/16”

turnbuckles till just one thread shows inside the body of the turnbuckle. Add a thimble to each

turnbuckle eye and secure the cable at each turnbuckle with two clips.

6. Element #1 is last and requires the most attention. SEE LINEAR LOADED ELEMENT ASSEMBLY

drawing. This element is almost the same as #2 except for the linear loading. Prepare the element

as shown except for the linear loading (3/16” dia. Rods). Now place the element on a level surface

with the support post up. FROM THE ELEMENT BUTT SIDE, feed a 3/16” LINEAR LOADING

RODS through the flat, support insulator and into the LL ARMS until 1/2” extends beyond each

arm. Tighten the 8-32 x 1/4" set screws. Using the 3/8 x 3” “Push tube”, Install two SHAFT

RETAINERS, one at a time, onto this rod tip and snug up against each linear loading arm.

NOTE: to start the RETAINER, hold the 3/8 x 3" PUSH TUBE in your hand with one end between

your thumb and forefinger. Now center retainer on this end, “dish” into tube, and hold in place with

the same thumb and forefinger. Grasp the linear loading rod near the end with your other hand and

firmly push the retainer onto the rod.

Next, cut two 9 foot (108”) lengths of HPTG 1200 Philistran. Note that one of the two center

grooves in the pre-assembled LINEAR LOADING CLAMP assemblies is “on center”. Slip about 4”

of the HPTG 1200 through the center groove and back through the other so about 2” of cable is

there for the 1/8” cable clip. Now slide this assembly on the rods to the dimension shown. Tighten

the center screw enough to hold the assembly together. Align it so it is parallel with the ground and

tighten all screws. Double check you dimension to make sure nothing has slipped. Correct if

necessary. Repeat for the other element half.

Now attach the other end of the HPTG 1200 cables to center 5/16” turnbuckles. Open the

turnbuckle first and install a cable eye in each turnbuckle. Pull the lines tight and tighten the clips.

Final tensioning of the linear loading rods is done with the turnbuckles. Adjust until each element

droops 10 to 16 inches at the tip. NOTE: The element is most stable in wind with a small amount of

droop.

8-30LP9 ASSEMBLY MANUAL

LINEAR LOADED ELEMENT ASSEMBLY

7. BOOM ASSEMBLY

Wipe off any dirt or grit from the coupling rings on the end of the long 3” section. Also clean the

inside of the 4” x 20 foot section. Lubricate the inside of the 4” tube and the coupling rings lightly

with oil or zinc paste Gently insert the 3” section into the 4” boom section. Align the holes, install

the 13/8-16 x 4-1/2” bolts and locknuts and tighten. Clean the boom tip section and slip it into the

main section. Install the 1/4-20 x 3-1/2” bolts and locknuts.

Install the 3/8 EYEBOLTS to the outer ends of the boom, securing with

3/8-16 nuts and lock washers. Align the eyes parallel with the boom and tighten.

8. Orient the boom with the eyebolts "up”. Using a tape measure and a marking pen or masking tape,

place a mark 1/2” in from the rear of the boom. This will be where you position the back edge of

the clamp plate for element #1. Now measure forward 98” from that mark and make another mark

for element #2. Continue marking the locations of all the elements using the element spacing

figures given on the Dimension Sheet.

9. Attach Element #1, the linear loaded element, to the boom. For ease of element installation,

support the boom about 3’ above ground, eyebolts "up." Slip Element #1 over the rear of the boom,

placing the back edge of the rear plate on your first mark. ALIGN the elements horizontal

perpendicular to the eyebolts and tighten bolts EVENLY and firmly. Use element #1 as the element

alignment reference.

10. Mount element #2 and align and tighten as before. Note it is usually easier to begin installing the

phasing lines at this time between each new element mounted. Mount the next to the longest pair

as shown on the dimension sheet. Hold the spacer in place loosely around the boom with a large

nylon tie but don't tighten it yet. Adjust phasing lines so that their bends are even and the lines run

parallel to the boom.

ALSO ATTACH THE 13 TURN COIL ACROSS ELEMENT #1 Tighten only the clamps on Element #1

at this time. After installing element number #3, then install the longest set of phasing lines

between #2 and #3 and tighten the clamps at Element #2, and so on. Continue until you get to

element #8 where the 4:1 BALUN is attached. Add the two 3 turn COILS to the balun and attach

the other end of the coil leads to the bolts that tighten the rod clamps.

11. Now mount the DIRECTOR as shown on the DIMENSION SHEET. Align the completed elements

as required with the element #1 at the other end of the boom.

Attach the BOOM TO MAST PLATE using 4 more 4” machined saddles. Mount the plate at the end

of the 4” boom section. This should be close to the physical balance point as well. Reshape the

phasing lines as needed to clear the plate by at least 1/2”.

8-30LP9 ASSEMBLY MANUAL

12. OVERHEAD BOOM SUPPORT SYSTEM.

Install a temporary mast if possible to get the overhead system just right before installing the antenna.

Attach one end of the HPTG-4000 Philistran cable at the eyebolt at the REAR end of the boom.

Install a thimble or cable eye in the eyebolt. Secure the cable using two 1/4” cable clips. Repeat at

the other eyebolt. Attach the turnbuckle plate to the mast about 5 feet above the boom to mast

plate. Open the 3/8 forged JAW AND EYE turnbuckles till just one thread is showing inside the of

the turnbuckle. Attach the JAW end of each turnbuckle at the plate. Insert a thimble or cable eye

in each turnbuckle eye and then attach the two HPTG-4000 cable, tensioning the cables and

securing with two more clips on each. Do final boom straightening with the turnbuckles now or at

the time of installation on the tower.

13. Check ALL hardware for tightness. Check ALL element sections, especially tip sections, for correct

placement. Make any final adjustments to linear loading tension.

14. Attach feedline section to balun. Route from element #8, back to boom to mast plate. Secure at

regular intervals with tape or nylon ties.

15. When mounting this log periodic on a tower or mast with other antennas there may be interaction

with other nearby antennas, particularly if they are resonant in the 8 to 30 MHz band. In general

VHF and/or UHF antennas mounted for HORIZONTAL POLARITY should be at least 40 inches

above or below the log antenna. Use good quality 50 Ohm feed line to feed the log and be sure

your tower and rotator system can handle to wind area and weight of this antenna.

THIS COMPLETES ANTENNA ASSEMBLY

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

8-30LP9 ASSEMBLY MANUAL

Andere M2 Antenna Systems Antenne Handbücher

M2 Antenna Systems

M2 Antenna Systems 10M7DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 7-10-30LP8 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 400-800-8 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 40M2C Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 12M4DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 420-450-11HP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 40M3L Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 249CP24 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 11M5DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 436CP16 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 303CP26 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems Eggbeater EB-310 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 137CP14HD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 32 HO LOOP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 222-10EZ Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 406-6SX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems FGHM64 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M5XHP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 215-470LP16 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M HO LOOP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 420-50-11 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 23CM22EZB Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2M-440XPSS Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 80M2L Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung