M2 Antenna Systems 248CP22A Bedienungsanleitung

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.00

Model .........................................248CP22A

Frequency Range.......................235 To 260 mHz

*Gain ..........................................13.8 dBi

Front to back ..............................20 dB Typical

Beamwidth ...............................E=36° H=40°

Feed type ...................................“T” Match

Feed Impedance........................50 Ohms Unbalanced

Maximum VSWR........................1.5:1 Typical

Input Connector..........................“N” Female

Power Handling..........................1 kW

Boom Length / Dia......................139-1/2” / 1”

Maximum Element Length..........25”

Turning Radius:..........................84”

Stacking Distance.......................68” High & 71” Wide

Mast Size....................................1-1/2” to 2” Nom.

Wind area / Survival...................0.93 Sq. Ft. / 100 MPH

Weight / Ship Wt.........................5 Lbs. / 8 Lbs.

M2 Antenna Systems, Inc.

Model No: 248CP22A

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

FEATURES:

The 248CP22A is high performance circular polarized antenna with a remarkably clean pattern. The pattern is

important in order to match the antenna’s noise temperature with modern low noise preamps. This antenna is ideal for

satellite work but is also excellent for terrestrial uses like ATV, repeater operation, and long haul tropo DX.

The CNC machined driven element module is O-ring sealed and weather tight for low maintenance and long-term

peak performance. Internal connections are encapsulated in a space-age silicone gel that seals out moisture and im-

proves power handling. The 3/16” 6061-T6 rod elements are centered to minimize interaction and maintain good elliptici-

ty. Insulators are UV stabilized and locked in place with stainless keepers. Rugged construction, uncompromising perfor-

mance for the boom length: that’s the M2248CP22A!

248CP22A DIMENSION SHEET

248CP22A ASSEMBLY MANUAL

TOOL REQUIRED FOR ASSEMBLY: screwdriver, 11/32 nut driver or wrench, 7/16” and 1/2” socket or end

wrenches, measuring tape.

1. Assemble the boom using 8-32 X 1-1/4 screws and locknuts to join sections. (SEE DIMENSION SHEET).

ASSEMBLING THE HORIZONTAL ELEMENTS

2. Lay out the elements by “Horizontal” length and position as shown the DIMENSION SHEET. Start with the

reflector (longest) element. Balance it on your finger to find rough center and push on a black button

insulator to about 1/2” off center. Push the element through the holes 1.937” from the rear of the boom and

install the second button, snugging it up into boom. DO NOT BOTHER CENTERING the element at this time

and DO NOT INSTALL the stainless steel shaft retainers yet. It is easier to do it after all the horizontal

elements are installed in the boom.

3. Install the 3/16” rod DRIVEN ELEMENT as you did the reflector. Then continue with the installation of the

DIRECTORS. Note: the Director Elements do not consistently diminish in length from rear to front, so pay

close attention to length and position.

4. Now begin centering the elements. Use a tape measure to EQUALIZE the amount the element sticking out

on each side of the boom. Once you have all the elements centered, sight down the element tips from the

rear comparing each side. Look for any obvious discrepancies and correct if found.

5. Stainless steel SHAFT RETAINERS lock the

elements in place. They should always be

used for permanent and long term antenna

installations. For portable or temporary use,

the button insulators are adequate for holding

the elements and the retainers may be left

off. To install the stainless steel SHAFT

RETAINERS, use thumb and forefinger to

hold the retainer over the end of the PUSH

TUBE ( 3/8" x 3" tube, supplied in the kit),

internal fingers on retainer dished into tube.

HOLD THE ELEMENT FIRMLY TO

PREVENT IT FROM SLIDING OFF CENTER

and press the retainer onto the element end

and continue until retainer butts on insulator

button. Locking pliers, lightly clamped up against opposite button insulator will help maintain center

reference (if you push the first retainer too far, remove element from boom, push retainer completely off the

element, and start over). Install another retainer to the opposite side of the element. Continue installing

retainers until all elements are secured.

6. Mount the HORIZONTAL P.S. DRIVEN ELEMENT ASSEMBLY to the TOP of the boom using a single

8-32 X 1-1/4" screw (SEE PICTURE).

7. Install the 8-32 x 1/4” set screws (internal Allen head - tool supplied) into the SHORTING BARS. Slide the

bars onto the 1/4" Driven Element Block Rods and the 3/16" driven element rod. Position the Shorting Bars

as shown on dimension sheet.

248CP22A ASSEMBLY MANUAL

ASSEMBLING THE VERTICAL ELEMENTS

Note: The vertical element set is shifted forward on the boom by 1/4 wave lengths. This increases isolation

between element planes, improving circularity and ease of phasing / matching the two element sets.

8. Repeat steps #2 through #5 for the Vertical elements, using the Dimension Sheet as your guide to lengths and

spacing.

INSTALLATION OF THE VERTICAL DRIVEN ELEMENT BLOCK DETERMINES THE CIRCULARITY OF

THIS ANTENNA. THE ORIENTATION OF THE BLOCK FOR RHC - RIGHT HAND CIRCULARITY, IS

SHOWN ON THE DIMENSION SHEET.

9. Viewed from the rear of the boom (rearmost Reflector HORIZONTAL), the VERTICAL Driven Element Block

mounts to the LEFT hand side of the boom with the two Balun connectors oriented to the FRONT. Secure with

8-32 x 1-1/4” screw. Install the Shorting Bars as in step #7.

10. Before installing the Baluns and Matching / Phasing Harness, thread 3/8” SEAL NUTS fully onto all

connectors, with the black Neoprene face of the nuts facing out. Attach Baluns and Phasing lines to the

Driven Element Blocks and Junction Block as shown on the picture below. Tighten the connectors gently

using a 7/16" end wrench. Once the connectors are tight, back the Seal Nuts out and finger-tighten firmly up

against the face of the connectors (or tighten gently with 1/2” end wrench). A lot of torque is unnecessary.

Depending on model and polarity, the Vertical balun may loop around another element. This is normal. Form

balun coax until it is close to the boom and secure with a nylon cable tie. Also secure the other balun and the

matching / phasing harness coax with cable ties. Ties should be snug but not crushing or kinking the coax.

11. Use good quality coax and “N” connector for your feedline (see Installation Tips). Secure feed coax near

connector on Junction Block, to provide stress relief. Allow about 60” of coax to hang in a loop between the

rear end of the boom and the reattachment point (at least 12” beyond element tips) on the mast or crossboom.

Do not route feedline thru boom to mast plate as exiting antenna here will adversely affect circular

field.

12. The boom to mast plate is normally mounted to the boom at the balance point (SEE DIMENSION SHEET).

Since the feed line represents significant weight it is best to have it attached and fastened to the boom with

cable ties before final mounting the plate. Use two 1" U-bolts and the stainless nuts and lock washers

provided. DO NOT OVER TIGHTEN. 2” U-bolts (and stainless steel nuts / lock washers) are provided for

mounting the antenna to your NON-CONDUCTIVE mast or crossboom. Other size u-bolts and cradles are

available upon request.

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

248CP22A D.E. & PHASING LINE DETAIL

D.E. BALUN

PHASE LINE

1/4 WAVE

PHASE LINE

3/4 WAVE SCREW

8-32 X 1-1/4”

P.S. BLOCK JUNCTION

BLOCK

D.E. BALUN

D.E. BLOCK

2.75

1.625

248CP22A BOOM TO MAST

DESCRIPTION QTY.

Boom section #1, 1 x .058 x 55" SOE ................................1

Boom section #2, 1 x .058 x 60" SOE .................................1

Boom section #3, 1 x .058 x 23”...........................................1

Boom extension tube, 1” x 0.058 x 10-1/2”...........................1

Elements, 3/16" alum. rod x (see dimension sheet) ............22

Driven Element Block Assembly...........................................1

Polarity Switch Block Assembly............................................1

Junction Block Assembly (SADE0065) ................................1

Balun, RG-6U X 20”, halfwave length...................................2

Phasing Line, RG6-U X 11”, quarterwave length ................1

Phasing Line, RG6-U X 31”, three quarterwave length........1

Shorting Bars, 0.75 x 1.532 x .250" (M2ASB0090) ..............4

Boom to Mast Plate, 3 x 4 x .125" (M2APT0019).................1

Assembly instructions ..........................................................1

HARDWARE BAG #1

U-bolt and cradle, 2".............................................................2

U-bolt, 1" no cradle ..............................................................2

Nut, 5/16-18 ss.....................................................................4

Lockwasher, 5/16" ss ...........................................................4

Nuts, 1/4-20 ss .....................................................................4

Lockwasher, 1/4-20 ss .........................................................4

IN HARDWARE BAG #2

Button insulators, 3/16" black ..............................................44

Shaft Retainers, 3/16" ss......................................................44

Screw, 8-32 x 1-1/4" pan head,ss .......................................7

Set screw, 8-32 x 1/4" ss .....................................................8

Locknut, 8-32 ss...................................................................4

Seal nuts, 3/8-32 gold zinc...................................................8

Allen wrench, 5/64" ..............................................................1

Push tube, 3/8 x 3" (for retainer installation) ........................1

Nylon cable ties, 8"...............................................................4

M2ANTENNA SYSTEMS, INC.

4402 N. Selland Ave.

Fresno, CA 93722

(559) 432-8873 Fax: 432-3059

www.m2inc.com Email: [email protected]

248CP22A PARTS & HARDWARE

Inhaltsverzeichnis

Andere M2 Antenna Systems Antenne Handbücher

M2 Antenna Systems

M2 Antenna Systems 440-6SX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2MXP20 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 23CM22EZB Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M7JHVHD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-460-11HD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems FG170-230-5 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 902-14WLC Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 12M4DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems FGSD-2.4DH Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 17M5DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 8-30LP9 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems EB-144/RK2M Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-18X Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6-30LP11 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M-3SS Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 400-800-8 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 436CP16 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 215-470LP16 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 450-800-12 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 146CP8 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 418CP30 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M3 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 11M5DX Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung