M2I TOPRW Bedienungsanleitung
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
1 / 23
M2I Corporation
Industrial HMI Touch Panel
TOPRW
HW Installation Manual
Thank you for purchasing the industrial HMI touch panel series of M2I corporation.
Please read this manual carefully to know installing, wiring, operating this equipment for safe use of
this product.
Chapter1. Safety Precautions
Chapter2. Overview
Chapter3. General Specifications
Chapter4. Part Names and General Specifications
Chapter5. Interface
Chapter6. Installation
Chapter7. Wiring
Chapter8. Maintenance
Chapter9. Warning Label
Chapter10. Products Label
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
2 / 23
Contents
Chapter 1. Safety Precautions .......................................................................................................................................... 4
Before Using the Product ........................................................................................................................ 4
General Precautions.................................................................................................................................... 4
Design Precautions ..................................................................................................................................... 4
Wiring Precautions ...................................................................................................................................... 5
Installation Precautions ............................................................................................................................. 5
Disposal Precautions .................................................................................................................................. 5
Cell Type Battery Specifications and Exchange ............................................................................. 5
Chapter 2. Overview ............................................................................................................................................................. 6
2.1 Introduction of Products .......................................................................................................................... 6
2.2 Package Contents ........................................................................................................................................ 6
2.3 Explanation of Model Name .................................................................................................................. 7
Chapter 3. General Specifications .................................................................................................................................. 8
Chapter 4. Part Names and General Specifications ....................................................................................................... 9
4.1 TOPRW0500WD ............................................................................................................................................ 9
4.2 TOPRW0700WD .......................................................................................................................................... 11
4.3 TOPRW1000WD .......................................................................................................................................... 13
Chapter 5. External Device Interface ........................................................................................................................... 15
5.1 Serial Communication Specifications ................................................................................................ 15
5.1.1 RS-232C ...................................................................................................................................................... 15
5.1.2 RS-422/485 ............................................................................................................................................... 15
5.1.3 COM1 Connector Pin No. and Signal Name ............................................................................. 15
5.1.4 COM2 Connector Pin No. and Signal Name ............................................................................. 16
5.2. Ethernet Communication Specifications ........................................................................................ 16
5.2.1 Ethernet ...................................................................................................................................................... 16
5.2.2 RJ-45 Pin Layout ..................................................................................................................................... 16
5.3 USB Communication Specifications .................................................................................................. 17
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
3 / 23
5.3.1 USB Host .................................................................................................................................................... 17
5.3.2 USB OTG .................................................................................................................................................... 17
Chapter 6. Installation ....................................................................................................................................................... 17
6.1 Insatllation Requirements ...................................................................................................................... 17
6.2 Installation Procedure .............................................................................................................................. 18
Chapter 7. Wiring ................................................................................................................................................................ 19
7.1 Power Wiring ............................................................................................................................................... 19
7.2 Ground Wiring ............................................................................................................................................ 20
Chapter 8. Maintenance ................................................................................................................................................... 21
8.1 Cleaning the Display ................................................................................................................................ 21
8.2 Periodic Check Points .............................................................................................................................. 21
8.3 Problems with the Device ...................................................................................................................... 21
8.4 System Recovery Settings Switch ....................................................................................................... 22
Chapter 9. Products and Warning Label Location................................................................................................ 23
Chapter 10. Products Label ............................................................................................................................................. 23
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
4 / 23
Chapter 1. Safety Precautions
■ Before using the product
To use the product safely and effectively, please read the contents of this manual thoroughly before use. Please
keep to the safety precaution, for it is to prevent accidents and potential danger from occurring. Safety
precaution is classified into ‘Warning’ and ‘Caution’ and their meanings are as follows
.
Also the indicated
illustrations on the product and in the manual have the following meanings.
Violating the instruction may result in serious personal injury or death.
Violating the instruction may result in slight personal injury or product damage.
Be cautious, for danger may be present.
Be cautious, for there is a possibility of an electric shock.
■ General Precautions
Do not press the screen with a hard or sharp object (awl, screwdriver, pen) with too strong a force.
It may cause malfunction of touch due to damage of the front sheet.
Do not use or store in an environment with high vibration.
Do not allow foreign objects such as water, liquids, or metal powders to enter the product. This may cause
breakage or electric shock.
Do not allow foreign objects such as water, liquids, or metal powders to enter into the front(screen)
protective sheet. The screen may be invisible or may cause a malfunction of the touch.
Use the radio or mobile phone at least 30cm away from the main unit.
Two or fewer bright spots may appear on the LCD screen, and certain areas may appear brighter, but this is
not a defect in LCD characteristics.
Do not store or operate in direct sunlight. Direct sunlight can change the properties of the LCD.
■ Design Precautions
Install protection circuit on the outside of Products to protect the entire control system when external power
supply or Products have problems.
As the malfunction & incorrect result of Products could damage the stability of the entire systems
and human body, you must install damage preventing interlock circuit such as emergency stop,
Protective circuits, positioning upper and lower limit switch and interlock for forward/reverse
operation.
When computer or other controllers communicate and exchange data with products or change operation
mode of products, set up protective sequence program in PC or Controller for protecting system from
communication error.
The output signal or communication lines should be separated from the power line or high tension wire.
They should be installed 100mm (3.94 Inch) or more from each other.
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
5 / 23
■ Wiring Precautions
Be sure the wiring is done correctly by checking the product’s rated voltage and the terminal layout.
Incorrect wiring could result in fire, damage or malfunctions.
Tighten the terminal screw with the specified torque. If the screws of terminal are loose, It could result
in short circuit, fire, malfunctions. FG Terminal must be used a dedicated ground. Not doing so could
result in malfunctions.
a. Grounding should be the Class 3 grounding. The cable for grounding should be more than 4㎟
b. grounding point be closed to the products and make short the distance to the ground cable if possible.
Please see below.
■ Installation Precautions
Do not install the location which exceeds allowed temperature. Product can be damaged or shorten the life.
Especially Install environment as below should be avoided.
Do not Install product to the place which the ambient temperature is out of limits, from 0℃ to 50℃ or on the
surface of control board which high pressure equipment is installed..
Do not install to the place where strong shock or vibration continuously have impacted on product.
The space between back of product and back of control board must be more than 100mm for maintenance
and ventilation.
In order to improve water retention and ventilation, the space between the back of the main body and
the console box should be 100mm or more, and install the cooling fan when installed in an enclosed
space
■ Disposal Precautions
When you dispose of product and battery, please treat it as industrial waste. It can create poisonous substances
or explosion.
■ Cell Type Battery Specifications and Exchange
Mounted on mainboard Model MS920SE Battery is not replaced by the user. If the battery has run out of service,
please contact our Customer Support Center for replacement and inspection.
Item Content
Battery Voltag
e
DC 3
V
Battery Model MS920SE (lithium
/
Recharg
e
able )
Battery lifetim
e
Permanent (In case of ambient temperature 25℃)
Batter
y
Discharg
e
Last about
7
days After turn it off
* Depending on the model specifications are subject to change
.
■ All field-wiring connections to this unit shall be from Limited Voltage / Limited Current,
below 24 Vdc isolated secondary source with an output fuse, or Class 2
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
6 / 23
Chapter 2. Overview
2.1 Introduction of Products
This industrial HMI touch panel is an industrial control device required in industrial field. It is a device based
on RS-232C and RS-422/485, Ethernet which is used for the basic purpose of communication with another
device (PLC)
2.2 Package Contents
The components of the product are as follows.
Before using the product, please check that all of the following components are included.
Item Figure Quantity
Process Module
And
Manual
1
Clamp
4
Power Connector 1
Accessories
(Sold separate)
USB Memory
USB Cable
SD Card
Front Protect Sheet
User Options
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
7 / 23
2.3 Explanation of Model Name
TOPRW □□ □□ □ □
Series Display Size Option Resolution Power
05 : 5.0” 00 : Standard Q : QVGA (320*240) A: AC
07 : 7.0” 10 : Premium V : VGA (640*480) D: DC
10 : 10.2” S : SVGA (800*600)
X : XGA (1024*768)
W: WQVGA (480*272)
WVGA (800*480)
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
8 / 23
Chapter 3. General Specifications
3.1 Power Specifications
Power
Input Voltage DC24V
Input Voltage Range DC 20~28V
Consumption Power
TOPRW0500WD Under 12W
TOPRW0700WD Under 12W
TOPRW1000WD Under 15W
Voltage endurance DC 24V, Within 10 ㎳
Insulation Resistance 500V DC, 10 ㏁
3.2 Memory Specifications
Screen Memory 128MB
Backup Memory 512KB : System buffer(5K Word),
Including Alarm/Logging/Recipe
Backup Period Permanent
Real Time Clock Built in(by Battery))
3.3 Environment Specifications
Operation Temperature (℃) -10 ~ +50
Storage Temperature (℃) -20 ~ +60
Operation Humidity (%RH) 0 ~ 90 (No dew)
Atmosphere No corrosive gas
Vibration Endurance Amplitude: 10≤F＜25 ㎐(2G) X,Y,Z each direction(for 30 minutes)
Noise Immunity 1000Vp-p(Pulse width 1 ㎲)
Static Electricity Discharge Connective discharge from EN61000-4-2: ±4 ㎸
Shock Endurance 10G X,Y,Z each direction(for 3 times)
Surge Voltage 500V(Line-Line)
Ground Connection Class 3(Under 100Ω )
Protection Classification Conform to IP65
3.4 Structure Specifications
TOPRW05 TOPRW07 TOPRW10
Weight 0.4 0.72 1.7
Cooling System Natural Air Circulation
Case Material PC(Flameless)
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
9 / 23
Chapter 4. Part Names and General Specifications
4.1 TOPRW0500WD
4.1.1 External Dimension
Model F1(mm) F2(mm) S1 (mm) S2 (mm) R1(mm) R2(mm)
TOPRW0500WD 150 114 41.8 35.8 135 99
4.1.2 Front Part Names and Specifications
M2I Corporation Industrial HMI Touch Panel HW Installation Manual
M2I Corporation
M2I Bldg, 35-11, Jeonpa-ro 24beon-gil, Manan-gu, Anyang-si, Gyeonggi-do, 430-857, Korea. Tel :+82-70-465-3366,Fax:+82-31-465-3355 www.m2i.co.kr
10 / 23
No. Part Description
① LCD TFT 16M Color LCD
② Touch Panel Analog Touch
③ Front Sheeet Front Cover Sheet for Damp Proof and Dust Proof
4.1.3 Rear Part Names and Specifications
No. Part Form Description
① Rubber Packing - Silicone Gasket for Impact Buffering and IP Securing
for Wall Mounting
② Status LED 3 Status of Power, Communication and CPU
③ COM1 Connector DSUB9 RS-232C Serial Comm. with PLC
④ COM2 Connector DSUB9 RS-232C/422/485 Serial Comm. with PLC
(Switchable the Comm. Via Software)
⑤ ETHERNET Connector RJ45 10BASE-T/100BASE-TX, Auto-MDIX
⑥ Power Input Terminal TB 5mm 3P Power Supply of Main Unit(DC 24V)
⑦ USB Connector
MINI USB Type AB
USB Connectors for Storage Options
⑧ SD Card Slot SD Card Slot SD Card Insert Connector
⑨ Mode Switch DIP Switch 2Digit Set Up System Switch
⑩ Reset Switch Tact Switch System Reset Switch
⑪ Diagnose Connector 2mm 4P Diagnose System (Manufacturer Only)
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere M2I Touchscreen Handbücher
Beliebte Touchscreen Handbücher anderer Marken
IBASE Technology
IBASE Technology ASTUT-152-RE1S Bedienungsanleitung
YASKAWA
YASKAWA TP 610C Bedienungsanleitung
B&R
B&R Power Panel C Series Bedienungsanleitung
Beijer Electronics
Beijer Electronics X2 control Bedienungsanleitung
AXIOMTEK
AXIOMTEK GOT321W-521 Bedienungsanleitung
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Bedienungsanleitung
