Magenta Research MultiView XRTx Bedienungsanleitung

MultiView

XRTx

Transmitter

Quick Reference

Setup Guide

Magenta Research

128 Litchfield Road, New Milford, CT 06776 USA

(860) 210-0546 FAX (860) 210-1758

www.magenta-research.com

Connect with Confidence

MAGENTA MULTIVIEW™ SERIES

Magenta Research

128 Litchfield Road

New Milford, CT 06776 USA

This document and the Magenta Research products to which it relates, and the copyright

in each, is the property of Magenta Research. Neither the document nor the products may

be reproduced by any means, in whole or in part, without the prior written permission of

Magenta Research. Magenta Research makes no warranty or representation, either express

or implied, with respect to this software or documentation, including their quality,

performance, merchantability, or fitness for a particular purpose. As a result, this software

or documentation are licensed "as is" and you, the licensee, are assuming the entire risk as

to their quality and performance.

In no event will Magenta Research be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use of or inability to use the software or

documentation.

Magenta Research and the Magenta Research logo are trademarks of Magenta Research.

All other brands, product names, and trademarks are the property of their respective

owners.

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy, and if

not installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested

and found to comply with the limits for a Class A computing device in accordance

with the specifications in Subpart B of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when the equipment is

operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct

the interference.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission

from digital apparatus set out in the Radio Interference Regulation of Industry

Canada.

EUROPEAN UNION DECLARATION OF CONFORMITY

The manufacturer declares that this product meets the requirements of

EU Directive 2004/108//EC.

This Magenta Research LTD product is Underwriters Laboratories I.T.E. listed when

installed accordingly to this guide.

FCC/IC RFI STATEMENTS, EU DECLARATION OF CONFORMITY

MAGENTA MULTIVIEW™ SERIES

Contents

Chapter Page

1. Specifications...................................................................................................3

2. Introduction ........................................…..........................................................4

2.1 Overview.....................................................................................................4

2.2 Equipment You May Also Need..........................................................…....4

2.3 Compatible Cabling ........................................................................…...….4

3. Setup and Installation..........................................… ......................................….5

3.1 Data Mode Configuration..............................................................................5

3.2 Cabling Considerations................................................................................5

3.3 Making the Connections................................…............................................5

3.3.1 Connections and Setup in General .......................................……......5

3.3.2 Connections on the Single-Port VGA/Audio……..............………..…..6

3.3.3 Connections on the Single-Port VGA/RS-232………………....………7

3.3.4 Connections on the T4 VGA/Audio Transmitter

T4 VGA/RS-232 Transmitter...............................................…..……....8

3.3.5 Connections on the single port SA/SAP series………………....……...9

4. Troubleshooting..................................................................................................10

4.1 Common Problems ......................................................................................10

Appendix A. Cabling Pinouts.........................................…......................................12

Appendix B. Setting Sync Signal Output Termination.....…....................................14

Appendix C. DC Restore for AC coupled Signals…........…....................................15

Appendix D. XRTX Configuration Settings.………….............................................16

Appendix E. Serial Daughterboard SDB Setting ……………………......................18

Appendix F. Mounting Options…….......................................................................20

Appendix G. Pollable Serial Mode..........................................................................21

Appendix H. DDC Modes……..…..........................................................................25

Appendix I. Setting Sync Mode…..........................................................................25

1.Specifications

Cable Required: Category 5, 5e, 6 shielded or unshielded twisted pair

Compliance: CE; FCC Class A, IC Class/class A, UL listed I.T.E Device

Video Support: VGA, SVGA, XGA, XGA-2, RGBHV, RGB, Composite, S-Video,

Component Video modes

Resolution and

Refresh Rate: Up to 2048 x 1536 at up to 72 Hz (receiver dependent)

Required Source

Impedance: Video OUT: 75 ohms;

Audio models: Audio OUT (if any): 600 ohms maximum

SPDIF audio models: 75 Ohm.

Required Destination

Impedance: Video IN: 75 ohms;

Audio models: Audio IN (if any): 600 ohms minimum

SPDIF audio models: 75 Ohm.

Audio

Characteristics: Channels: Right/Left summed;

Line Level 600 Ohm Unbalanced

SA/SAP versions are full stereo audio

Serial

Characteristics: Protocol: Asynchronous; transparent to data format;

transparent to data rates up to 19.2 kbps full duplex;

data rates to 115 kbps simplex, half-duplex modes.

SA/SAP versions are 3 wire, fixed baud rate of 9600.

Connectors: XRTx: (1) 4 position phoenix, (1) RJ-45, (2) HD15 F;

XRTx 232: (1) DB9 F , (1) RJ-45, (2) HD15 F;

XRTx SA/SAP: (1) 4 position phoenix, (1) DB9 F,

(1) RJ-45, (2) HD15 F;

Temperature

Tolerance: Operating: 32 to 104°F (0 to 40°C);

Storage: -4 to +140°F (-20 to +60°C)

Humidity

Tolerance: Up to 80% noncondensing

Enclosure: Steel

Power: +5 V ;

Consumption: 5 watts maximum

Size: 1.2"H x 4.2"W x 4.3"D (3.1 x 10.4 x 10.9 cm)

Weight: 1.0 lb. (0.45 kg)

MTBF: 100,000 hours

CHAPTER 1: Specifications

MAGENTA MULTIVIEW™ SERIES

2. Introduction

2.1 Overview

The Magenta MultiView™ Series extends VGA and video signals over ordinary

Category 5 cable.

This manual covers Magenta MultiView™ XRTx Universal Transmitters. These units

are field configurable for various video, audio and serial options. See Appendix D for

configuration settings.

The XRTx features the ability to report DDC information to the video source computer.

This allows for better control in choosing desired resolution and refresh rates which are

not always available if a valid DDC signal is not detected. See Appendix H for details.

SA series feature video, stereo audio and RS-232 signals on a single Cat5 and SAP

series units are similar to the above but have additional features for pollable serial.

For information on the respective receiver unit, please refer to the appropriate manual

included with the receiver.

2.2 Equipment You May Also Need

• Audio cable with RCA jacks or a 1.8” stereo plug.

• Video cable with HD15 connectors.

• Serial cable with DB9 connectors.

• CAT5 cable.

2.2 Compatible Cabling

Magenta Research products are compatible with Cat5/5e/6 data cabling as well as skew free

CAT5/5e cabling manufactured for video applications. Note that some skew free Cat5 is specific to

a particular vendor and is not compatible with our products. Please ensure any skew free CAT5

cable is non-proprietary prior to purchase/installation.

CAT6 cable, due to the manufacture method, can exhibit much greater skew than standard

CAT5/5e and may require skew compensation beyond what the standard product offers. Please

contact Magenta Research for assistance.

CAT5/5e/6 cabling for the Magenta MultiView™ Series must be pinned to the TIA-EIA T568B

wiring specification (see appendix A) We also highly recommend that all CAT5 cables be pre-

terminated and tested. Cables terminated on-site or in an existing infrastructure should be tested

before use to ensure compliance with the TIA-EIA T568B specification. Using incorrectly

terminated CAT5 cables can damage the Magenta MultiView™ Series.

The Cat5/5e/6 cable should be suitably rated Listed cable ( DUZX ) communication cables, TYPE

CMP, CMR, CMG or CM as designated in the NEC. Cables are to be installed in accordance with

the NEC and local building and electrical codes. This is the responsibility of the end user/installer

of this product.

WARNING

This equipment is not intended for, nor does it support,

distribution through an Ethernet network. Do not connect these

devices to any sort of networking or telecommunications

equipment!

Use only Magenta Research LTD approved MultiView power

adapters. Failure to do so, may damage this device and will void

warranty.

.CHAPTER 3: SETUP & INSTALLATION

3. Setup and Installation

3.1 Data Mode Configuration (RS232 and SA versions)

XRTx 232 serial transmitters are configured in full modem bidirectional serial modes. If

you are using the daisy chain receivers or a multi-output transmitter (T4,T5) a

MultiView™ CAT5 matrix switch or MultiView™ CAT5 distribution amp, this mode must

be changed to uni-directional broadcast . To do this, configure the internal Serial

Daughterboard (SDB) to change the transmitters & receivers serial mode operation

(See Appendix E). This configuration should be done before making any cable

connections and applying power.

Alternatively, remove the internal daughterboard and use the XRTx transmitters built in

simplex serial option with the appropriate jumper changes.

SA series offer RS232 serial in addition to stereo audio. The serial signal is 3 wire TX,

RX, Gnd and does not support full modem signals. Baud rates for the SA series are

fixed at 9600. Simplex modes are supported without jumper or other changes by simply

using the TX signal only. SA units require no configuration.

SAP series offer pollable RS232 serial in addition to stereo audio. The serial signal is 3

wire TX, RX, Gnd and does not support full modem signals. Baud rates for the SAP

series are fixed at 9600. Simplex modes are supported without jumper or other changes

by simply using the TX signal only. See Appendix G on configuration and using SAP

Series

3.2 Cabling Considerations

• We recommend mounting and connecting all cabling to the Magenta MultiView™

Series components before applying power.

• Makes sure that the CAT5 cable you intend to use has been tested to comply

with the TIA/EIA 568B wiring specification (See Appendix A).

3.3 Making the Connections

3.3.1 CONNECTIONS AND SETUP IN GENERAL

This section contains figures showing connections with the specific Magenta

MultiView™ Series models. In general, however, the connection and setup procedure at

both transmitter and receiver ends is as follows:

NOTE: all units must be the same type for all supported features to function correctly.

For example, an XRTx 232 must be connected to an AK600 232 for the serial signals to

function. You cannot use the serial option with an XRTX 232 and an AK600 that is

configured for simplex serial. Similarly, an XRTX SA cannot be used with an AK600A.

Video modes may function normally, but 4th pair options will not.

At the transmitter end :

1. Connect the source video to the Magenta MultiView™ Series transmitter video input

port, which is an HD15 connector labeled VIDEO IN.

2. If desired, attach a local monitor via the local monitor port to LOCAL OUT.

3. Make your audio or serial connections via the phoenix AUX I/O connector or DB9

IOIO connector as appropriate.

MAGENTA MULTIVIEW™ SERIES

4. Connect the CAT5 cable to the transmitter.

5. Apply power on the transmitter. The LED should light and, if there’s a local

monitor attached, a video image should appear on the monitor’s screen.

At the receiver end (refer to the appropriate receiver manual):

1. Connect the VIDEO OUTPUT HD15 connector to the display unit, and attach

any audio (AUX I/O) and/or serial connections (IOIO) depending on the model of

MultiView™ CAT5 Video System.

2. Connect the CAT5 cable to the LINK INPUT connection. If daisy chaining units,

connect the output CAT5 cable to the LINK OUTPUT connection.

3. Apply power. The LED should light and video should appear on the display

(make sure display is powered ON).

4. Adjust video levels and skew compensation per appropriate receiver manual.

3.3.2 CONNECTIONS ON THE SINGLE-PORT VGA/AUDIO

The single-port units with audio support video and audio signals over CAT5 cable. The

audio signal is line-level audio, and powered speakers are required. Note that there’s a

single connection for audio input. You can also use the transmitters and receivers to

make video-only connections without mono audio. Figure 3-1 shows the Single-Port

MultiView™ CAT5 Video System with Audio Transmitter connections, and Figure 3-2

shows the typical receiver connections.

Figure 3-1. Connections on the XRTx Universal Transmitter.

.CHAPTER 3: Setup and Installation

Figure 3-2. Connections on the AK600 with audio.

3.3.3 CONNECTIONS ON THE SINGLE-PORT VGA/RS-232

The Single-Port MultiView™ CAT5 Video System with RS-232 supports video and full-

modem serial (RS-232) signals over CAT5 cable. You can also use the transmitters and

receivers to make video-only connections without serial communications. Figure 3-3

shows the Single-Port MultiView™ CAT5 Video System with RS-232 Transmitter

connections, and Figure 3-4 shows typical receiver connections.

NOTE

Even though both transmitter and receiver units contain audio jacks,

audio is not supported on the RS-232 version. Plugging in audio cables

may interfere with the RS-232 serial communications.

Figure 3-3. Transmitter connections on the XRTx 232 Universal Transmitter.

MAGENTA MULTIVIEW™ SERIES

Figure 3-4. Receiver connections on the AK600 232

3.3.4 CONNECTIONS ON THE VGA/AUDIO T4/T5 TRANSMITTERS

The T4 four-port transmitter is used when the same signal is distributed

to multiple display devices. You set it up and cable it the same as you would with

the single-port transmitter. Figure 3-5 shows how connections are made on the

audio version, and Figure 3-6 shows how connections are made on the serial RS-232

T4S version.

NOTE

Serial communication mode is unidirectionally broadcast when using T4, T5

transmitters and daisy-chained receivers. In this mode, all other devices must be

of the simplex serial type. For more information, contact Technical Support.

Figure 3-5. T4 transmitter

connections with audio Figure 3-6. T4 transmitter

connections with serial

Inhaltsverzeichnis

Andere Magenta Research Sender Handbücher

Magenta Research

Magenta Research Voyager Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung