Magic Chef MCKC490B Bedienungsanleitung

4.9 CU.FT. BEER KEG COOLER

INSTRUCTION MANUAL

Model No.: MCKC490B

To ensure proper use o this appliance and your sa ety, please read the

ollowing instructions completely be ore operating this appliance.

TABLE OF CONTENTS

Names o the Parts _________________________________________________3

Important Sa ety Instructions ________________________________________ 4

Installation Instructions _____________________________________________ 4

Be ore Using Your Beer Dispenser ____________________________________ 4

Installation o Your Beer Dispenser ________________________________ 4 - 5

Electrical Connection _______________________________________________ 5

Installation Instructions or Beer Keg_______________________________ 6 - 9

Dispensing o Beer _________________________________________________ 9

Operating Your Beer Dispenser _____________________________________ 10

Setting the Temperature____________________________________________ 10

Automatic De rosting ______________________________________________ 10

Converting to an All Re rigerator ____________________________________ 10

Changing the Reversible Door_______________________________________ 11

Care and Maintenance _____________________________________________ 12

Troubleshooting Guide_____________________________________________ 12

Warranty ________________________________________________________ 13

NAMES OF THE PARTS

MODEL NO.: MCKC490B

1 Beer Tower

2 Plastic Gasket

3 Safety Guard Rail

4 Drip Tray

5 Adjusta le Thermostat

6 CO

Regulator

7 CO

Gas Cylinder

8 CO

Gas Cylinder Support

9 Evaporator

10 Reversi le Door

11 Beer Keg (not included)

12 Metal Plate

13 Metal Washers(2)

14 Castors with Lock (4)

IMPORTANT SAFETY INSTRUCTIONS







WARNING







To reduce the risk of fire, electrical shock,

or injury when using your Beer Dispenser,

follow these asic precautions:

• Read all instructions efore using the unit.

• WARNING: Risk of child entrapment.

• To avoid the possi ility of child entrapment, please take the following precautions

efore throwing out the appliance.

- Remove all doors from the unit.

- Leave the shelves in place so that children may not easily clim inside.

• Be ore you throw away your old unit: Take off the doors. Leave the shelves in

place so that children may not easily clim inside.

• Never allow children to operate, play with, or crawl inside the unit.

• Re rigerants: All refrigeration products contain refrigerants, which under the

guidelines of federal law must e removed efore disposal of product. It is the

consumer’s responsi ility to comply with federal and local regulations when

disposing of this product.

• Never clean unit parts with flamma le fluids. The fumes can create a fire hazard or

explosion.

• Do not store or use gasoline or any other flamma le vapors and liquids in the vicinity

of this or any other unit. The fumes can create a fire hazard or explosion.

-Save these instructions-

INSTALLATION INSTRUCTIONS

 Be ore Using Your Beer Dispenser

• Remove the exterior and interior packing.

• Check to e sure you have all of the following parts:

• 1 Safety Guard Rail

• 1 Drip Tray (2 Pieces)

• 1 CO

Cylinder Support

• 1 CO

Regulator (Box)

• 1 CO

Empty Cylinder(Box)

• 1 CO

Air Line Hose (Red)

• 1 Beer Keg Coupler (Box)

• 1 Beer Tower

• 1 Pull Handle (Beer Tower Faucet)

• 1 Metal Wrench

• 4 Plugs: For Guard Rail Holes

• 1 Metal Plate For Ca inet Bottom

• 2 Steel wire shelves

• 1 Steel Clamp for Red Hose

• 4 Castors with locks

• 2 Metal Washers

• Before plugging in the keg cooler, let it stand upright for approximately 2 hours. This will

reduce the possi ility of a malfunction in the cooling system from handling during

transportation.

• Clean the interior surface with lukewarm water using a soft cloth.

 Installation o Your Beer Dispenser

• This appliance is designed to e free standing only, and should not e recessed or uilt-in.

• Place your Beer Dispenser on a floor that is strong enough to support the Beer Dispenser

when it is fully loaded.

• Allow 3 inches of space etween the ack and sides of the Beer Dispenser, which allows the

proper air circulation to cool the compressor.

• Locate the Beer Dispenser away from direct sunlight and sources of heat (stove, heater,

radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase

electrical consumption. Extreme cold am ient temperatures may also cause the Beer

Dispenser not to perform properly. This unit is not designed for outside installation (ie

garages, porches, etc.)

• Avoid locating the Beer Dispenser in excessive humidity.

• Plug the Beer Dispenser into a dedicated, properly installed-grounded wall outlet. Do not

under any circumstances cut or remove the third (ground) prong from the power cord. Any

questions concerning power and or grounding should e directed toward a certified electrician

or an authorized service center.

• After plugging the appliance into a wall outlet, allow the unit to cool down for 2-3 hours efore

placing any contents in the Beer Dispenser compartment.

 Electrical Connection

This Beer Dispenser should e properly grounded for your safety. The power cord of this Beer

Dispenser is equipped with a three-prong plug which mates with standard three prong wall outlets to

minimize the possi ility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power cord supplied.

Use of extension cords is not recommended.

This Beer Dispenser requires a standard 115/120-volt, 60Hz electrical outlet with three-prong ground

receptacle. The cord should e secured ehind the Beer Dispenser and not left exposed or dangling

to prevent accidental injury.

Never unplug the Beer Dispenser y pulling the power cord. Always grip the plug firmly and pull

straight out from the receptacle.

WARNING

GAS CAN BE DANGEROUS

WARNING: CO

cylinders contain high-pressure compressed gas which can e hazardous if not

handled properly. Make sure you READ and UNDERSTAND the following procedures for CO

cylinders BEFORE INSTALLATION.

1. ALWAYS connect the CO

cylinder to a regulator. Failure to do so could result in explosion

with possi le injury when the cylinder valve is opened.

2. NEVER connect the CO

cylinder directly to the product container.

3. ALWAYS follow correct procedures when cylinders are changed.

4. ALWAYS secure the cylinder in an upright position.

5. NEVER drop or throw a CO

cylinder.

6. ALWAYS keep a CO

cylinder away from heat. Store extra cylinders in a cool place

(prefera ly 70°F). Securely fasten with a chain in an upright position when storing.

7. ALWAYS ventilate and leave the area immediately if CO

leakage has occurred.

8. ALWAYS check the D.O.T. test date on the cylinder neck efore installation. If over five (5)

years, do not use, return cylinder to gas supplier.

9. NEVER connect a product container unless there are two (2) safety’s in the pressure system:

a. One at or on the CO

regulator

. One at or on the product coupler or in the pressure gas line.







Warning







Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is

damaged, have it replaced y an authorized service center.

INSTALLATION INSTRUCTIONS FOR BEER KEG

Keg Installation Sketch

· Install the four castors with lock provided into the unit’s ottom (four screw holes pre-supplied)

The two metal gaskets are used for the front two Castors. Figure (1) efore installation. Figure (II)

is the final version.

(I) (II)

Metal Washers

Installation O CO

Cylinder Support

• Install the metal support provided onto the 4 studs located on the exterior ack wall. Align the

holes in the support with the studs and push down firmly. (See Figure 1)

Installation O CO

Cylinder

• The CO

Cylinder does not come filled. The cylinder must e filled with CO

prior to use.

• Install your fully charged cylinder into the support stand

Installation O CO

Regulator

• Attach the CO

regulator to the cylinder y turning the regulator nut onto cylinder valve, making

sure washer is securely inserted into connecting nut. Tighten snug using an adjusta le wrench

(not supplied) and assure there are no leaks. (See Figure 2)

Installation O CO

Air Line Outside Cabinet

• Remove plug located at the exterior ack (top left hand corner).

• Save it for later use if you decide to convert unit to a refrigerator.

• Insert the open end of the air line (red) line the ca inet through the uncovered hole.

(See Figure 4)

Installation O CO

Air Line Hose To Regulator

• Attach the open end of the red hose to the hose ar connection on the regulator

• Secure hose y using one clamp provided. Use pliers/screwdriver to tighten clamp to prevent

leaks. (See Figure 3)

Installation O The Beer Tower

• Remove the top plug y twisting and pulling out, saving it for later use if you decide to convert unit

to an all refrigerator unit.

• Unravel the eer line (clear hose) from the tower and insert the eer line and wing nut through the

uncovered hole on top.

• Lock the eer tower assem ly to the top and make sure to position the eer faucet so it is aligned

with the ca inet front (6 o’clock position). You accomplish this y aligning the ottom of the eer

tower to the 3 grooves on the top ca inet and tighten y hand clockwise to properly lock.

• The plastic gasket (# 2 in parts list), can e used to make the connection etween the tower and

the cooler tighter if needed. If Beer Tower will not turn to lock in place, try removing the plastic

gasket.

Installation O Protective Metal Plate

• This plate should always e installed when the keg is in place to protect against unnecessary

damage to the floor of the ca inet.

Fig. 1

Fig. 2

Fig. 3

Installation O The Beer Keg

• Position the eer keg directly in front of the open door. Using keg handles only, carefully lift the

eer keg. (See Figure 5)

• To place the eer keg inside the ca inet, race your knees ehind the eer keg. Lift the front of

the keg just enough so the front edge of the keg is resting on the front edge of the Beer Dispenser

ottom ca inet. (See Figure 6)

• Grasp the keg handles and slide it all the way into the ca inet.

Fig. 4 Fig. 5 Fig. 6

Installation O The Keg Coupler

• Insert the keg coupler provided into the locking neck of the eer keg and turn it clockwise to lock

into position, making sure the keg coupler is in the closed position. (See Figure 7)

Installation O The CO2 Air Line Hose

• Attach the end of the air line (red) hose provided to the hose connection on the keg coupler.

Connecting the beer tower to coupler

• Make sure the washer is properly inserted into the wing nut.

• Make sure the small round ead is in place (dropped down into the top of the coupler).

• Make sure the all retainer is in place on the coupler, with the ‘arms’ down into the coupler.

• Place wing nut into the top of the coupler turning until tight.

How to Tap a Keg o Beer

• Make sure that the CO

is turned off, and the Secondary valve on the regulator is in the ‘Closed’

position.

• Pull out and release the pressure release valve on the Coupler to purge any air pressure.

• Make sure the eer tower faucet is in the closed position.

• Pull tapping handle out and press downward until it locks into position. (See Figure 8) The keg is

now tapped.

Opening the CO

Cylinder Main Valve

• Make sure the secondary shut-off valve (shown in figure 9 in ‘Open’ position) is closed. To open

the main CO

cylinder valve, slowly turn the main valve counter-clockwise until fully open.

• Notice the needle on the regulator gauge start to clim .

Adjusting The CO

Regulator

The gauge monitors low internal keg pressure and should e adjusted to read etween 10-12 psi.

(See Figure 10). The pressure can e adjusted as needed.

•

Release adjustment lock nut marked 2.

•

Using a flat screwdriver, turn regulator screw marked 3.

To increase pressure, turn screw clockwise.

To decrease pressure, turn screw counter - clockwise.

•

Retighten lock nut marked 2.

•

Open secondary shut off valve to let CO

flow into the keg.

•

Allow several minutes for the keg to properly pressurize. Regulator gauge may drop while this

happens. (Note: Listen for hissing along all connections to identify if there are any leaks)

 Spanner Faucet Wrench

Spanner faucet wrench is provided for either removing or

tightening connection

 Plastic Faucet Lever

Attach the lack plastic lever (pull handle) to the top of the faucet y

tightening it y hand clockwise until the end, holding in the silver nut

underneath so it does not turn.

If there is still a small drip from the faucet, you may have tightened the

plastic lever too much and may need to unscrew silver snug counter-

clockwise (as shown) one turn.

DISPENSING OF BEER

• Keep eer keg refrigerated at all times.

• Never allow eer lines to dry out.

• Use clean eer glassware efore pouring.

• Hold glass at a 45° angle when 2/3 full, start to straighten glass as the glass fills.

• Always make sure the faucet handle is pushed all the way ack.

Note: Keg sizes that can e used in your eer dispenser

1/2 barrel 59 Liters 15.5 gals 1984 oz. 164/12-oz. Glass

1/4 barrel 30 Liters 7.8 gals. 992 oz. 82/12-oz. Glass

1/6 barrel 20 Liters 5.2 gals. 661 oz. 55/ 12-oz. Glass

1/8 barrel 15 Liters 4.0 gals. 496 oz. 41/ 12-oz. Glass

Note: Our Beer dispenser accepts standard kegs up to 16-1/8” in diameter, and up to 23-3/8” in

height. Check with your distri utor to make sure keg is correct size.

OPERATING YOUR BEER DISPENSER

 Setting The Temperature

To start, turn the temperature control kno to the maximum setting (6). Allow

the unit to run for 24 hours for the unit to cool properly. You may then adjust the

temperature to the desired setting.

In average room conditions of 70°F (21 ºC), set thermostat kno position

etween “4” and “5.

To turn off the Beer Dispenser, rotate the control kno to the “OFF” position.

Note: To accurately measure the temperature of liquid in the unit, place a cup of water

In the front corner, and place a liquid thermometer in the water.

During the summer when temperatures are warmer, we recommend that you adjust the control to a

cooler setting.

The time it takes to reach your desired temperature depends on the eer keg size and the room

conditons where the eer keg cooler is located. Normally, on setting of 6, it takes no more than 36

hours for a 1/2 arrel keg to cool down if the am ient temperature is 60°F to 75°F.

The more eer there is, the longer it will take to cool down.

Automatic De rosting

There is no need to defrost the Beer Dispenser. Defrost water collects and passes thru the drain

outlet in the rear wall into a tray located a ove the compressor, where it evaporates.

 Converting To An “All Re rigerator”

1. Turn off the control kno to the “OFF” position.

2. Close the main valve on the CO

cylinder.

3. Close the secondary shut-off valve on the regulator pipe.

4. Close the connection etween the eer keg and the keg coupler.

5. Drain any remaining eer from the lines.

6. Disconnect the eer line and CO

air line from the keg coupler

7. Remove the eer keg.

8. Remove the keg coupler.

9. Disconnect the air line from the CO

cylinder.

10. Remove the CO

air line from ca inet plug

11. Replace the air line rear ca inet plug

12. Remove the eer tower. Also pull the eer line thru the top of the ca inet

13. Replace the top ca inet plug

14. Adjust temperature as desired.

NOTE:

If the unit is unplugged, power lost, or turned off; you must wait 3 to 5

minutes efore restarting the unit. If you attempt to restart efore this time delay,

the Beer Dispenser may not start.

Andere Magic Chef Kühlschrank Handbücher

Magic Chef

Magic Chef RB17CA-1A Bedienungsanleitung

Magic Chef

Magic Chef MCBR360B Bedienungsanleitung

Magic Chef

Magic Chef MCBR460S Bedienungsanleitung

Magic Chef

Magic Chef HVDR430WE Bedienungsanleitung

Magic Chef

Magic Chef MCBR170B Bedienungsanleitung

Magic Chef

Magic Chef MCBM920W1 Bedienungsanleitung

Magic Chef

Magic Chef MCBR170BF Bedienungsanleitung

Magic Chef

Magic Chef MCBM920W Bedienungsanleitung

Magic Chef

Magic Chef MCQR1500ST Bedienungsanleitung

Magic Chef

Magic Chef MCBR465S Bedienungsanleitung

Magic Chef

Magic Chef MCDR450WEF Bedienungsanleitung

Magic Chef

Magic Chef MCBR350W2 Bedienungsanleitung

Magic Chef

Magic Chef HMR330WE Bedienungsanleitung

Magic Chef

Magic Chef MCR1010WEF Bedienungsanleitung

Magic Chef

Magic Chef MCBR980W Bedienungsanleitung

Magic Chef

Magic Chef HMBR350WEF Bedienungsanleitung

Magic Chef

Magic Chef MCBR405B Bedienungsanleitung

Magic Chef

Magic Chef MCBR270B Bedienungsanleitung

Magic Chef

Magic Chef MCR32CHW Bedienungsanleitung

Magic Chef

Magic Chef 440YW-2 Bedienungsanleitung

Magic Chef

Magic Chef MCBM920S Bedienungsanleitung

Magic Chef

Magic Chef MCBR1020W Bedienungsanleitung

Magic Chef

Magic Chef MCBR350WEF Bedienungsanleitung

Magic Chef

Magic Chef HMAR265WE Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung