MAGICO Q7 Handbuch

Assembly Procedure

1 | P a g e

Locate the Q7-10 Base Plate. Note that

the side with the beveled edge will be

the back/rear of the cabinet. It may be a

good idea to label this side as “rear.”

Remember any fasteners that go into

this base plate will be 2” ¼-20

fasteners with washers and red Loctite.

Locate the (2x) Q7-06 Braces. You will

fasten each of these down to the Q7-10

plate. Notice the orientation of the

braces. The small window cut out of the

top of the brace and the (2) through

holes at the top. The bottom side, which

has (3) through holes is the side that will

mount to the Base Plate.

Fasten these braces down with (x3) 2” ¼-

20 fasteners with washers and red

Loctite.

2 | P a g e

Locate the Q7-65 Short

Rails (Blue). You should

have 6 rails total, (4) of

these short rails are to be

kept as is. The remaining

(2) rails will need to have

their inner threaded

holes drilled out with an F

bit. The drilled out rail

will be mounted in the

“center” of these -06

braces. To start, attach

the -65 rails to the -06

braces as shown in the

images to the right.

These rails should be

fastened down with 7/8”

¼-20 fasteners with

washers and red Loctite.

Use (4) fasteners per rail

except for the center rail

in which you should use

(2).

Next install the Q7-03

Brace (Pink). This will

have to slide in sideways

and be inserted through

the (2) Q7-06s. Once

through, the cut-outs in

the -03 brace should line

up with the -06 braces.

3 | P a g e

Use the angled edge

on the end of this

brace to find the

braces orientation.

The longer edge (the

leading edge) should

be facing down, both

should be facing to

the rear of the

cabinet. Fasten the

Q7-03 down to the -

65s with 7/8” ¼-

20 fasteners with

washers and red

Loctite.

Locate the Q7-02

(Mint) Brace. Find

the side of it with

the

chamfered/beveled

edge. Slide this

brace. Slide this

brace in to the -06

braces and lay it

down flat on top of

the Q7-03. Do not

fasten this piece

down yet. For now,

simply leave this

brace here.

4 | P a g e

Locate the Q7-05 Brace (Yellow).

Slide it in through the -06 braces.

Instead of resting this brace on

top of the others, lift this brace

up and turn it sideways, allowing

it to rest on the inner ledges of

the -06 braces.

Check all braces to insure that

every brace has a beveled or

chamfered edge and that are

angled in the same direction.

Each brace should be angled like

so \

Now install the (2) drilled Q7-

65s (Red) at the midway point of

the -06 braces. The -65s can be

fastened with 7/8” ¼-20

fasteners with washers and red

Loctite.

5 | P a g e

Once both of the-65s are installed, bring

the Q7-02 up and mate it to the two -

65’s using 7/8” ¼-20 fasteners with

washers and red Loctite.

Install the last two undrilled Q7-65s

(Blue) to the -06s at the uppermost

mounting point. Fasten with 7/8” ¼-20

fasteners with washers and red Loctite.

Lift the Q7-05 up and fasten it to the

two undrilled Q7-65s. Fasten all

together with 7/8” ¼-20 fasteners with

washers and red Loctite.

Look at assembly from the side. Make

sure all chamfered edges line up. Make

sure the front side of the speaker has

each brace lining up flush to the front of

the baseplate. You can now lay this

assembly on its side (on a table).

6 | P a g e

Locate the Q7-04 (shown in orange). Place the

-04 in the skeleton assembly. Before fastening

down the -04 make sure all braces are flush

with the -04 and that everything lines up. The -

04 is a good indicator when a brace is not

flush, it will “stand out” amongst others. The

trick to fixing these braces will be to use a

power clamp.

Use the power clamp

to force a brace to

sit flush with the -04,

once flush, fasten

the -04 to the

skeleton assembly.

There is a chance

that the power

clamp will not be

effective. In these

cases, you will have

to loosen the

fasteners on the -65

braces and adjust

the questionable

brace.

Once this has been done, you will

flip the skeleton assembly up and

over and install an -04 on the

opposite side. Fasten the -04s to

the skeleton assembly with 7/8” ¼-

20 fasteners with washers and red

Loctite.

Fasten -04s to -10 plate with ¼-20

2” fasteners with washers and red

Loctite.

7 | P a g e

Grab the Q7-14 plate. Take note, this

plate has a large hole cut out of one

side, it should be on its chamfered

side. This indicates the rear/back side

of the cabinet.

Make this plate flush with the front of

the -04 braces before fastening down

tight with 2” ¼-20 fasteners with

washers and red Loctite. Fasteners

should come from the -04 up in to the -

14 plate and from the -06 up in the -14.

Don’t forget the ¼-20 2” fasteners

going up into the center of the plate.

You should be able to stand the

skeleton assembly up now. Check your

work against the model shown to the

right.

8 | P a g e

Unwrap and QC the Q7-17.

Check the rabbit, check

corners, and check every edge

for damage to the finish. If

everything passes and looks

good, you will put it down on a

clean table with foam and

paper, finished side down.

Locate the Q7-32 frame

batten. Install this frame

batten on the Q7-17.

Before fastening the

batten down, make sure

it is flush against the front

side of the cabinet, which

will be the non-angled

side. Fasten battens with

a 3/4” ¼-20 fastener with

washers and red Loctite.

Next up is the Q7-43

frame batten. This frame

batten should be installed

near the bottom of the -

17 plate. Positioning this

batten is a bit tricky, to

find its ideal location, use

a Q7-40, flush up against

the front/non-angled side

of the -17, and then

position the -43 batten

flush to the bottom side

of the-40. Fasten battens

with a 3/4” ¼-20 fastener

with washers and red

Loctite.

9 | P a g e

Andere Handbücher für Q7

Andere MAGICO Sprecher Handbücher

MAGICO

MAGICO Q3 Bedienungsanleitung

MAGICO

MAGICO Mini Bedienungsanleitung

MAGICO

MAGICO M6 Bedienungsanleitung

MAGICO

MAGICO S7 Bedienungsanleitung

MAGICO

MAGICO Q1 Bedienungsanleitung

MAGICO

MAGICO Q5 Bedienungsanleitung

MAGICO

MAGICO 5 Bedienungsanleitung

MAGICO

MAGICO V2 Bedienungsanleitung

MAGICO

MAGICO S3 MKII Bedienungsanleitung

MAGICO

MAGICO V3 Bedienungsanleitung

MAGICO

MAGICO Q7 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung